Question about 1997 Mazda 626

1 Answer

I unplugged my battery and when i plugged it back in it would not start could it be a fuse that blew?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,533 Answers

Check the fuse for the ignition give these websites a try www.alldatadiy.com and www.autozone.com if all fails stop by your local library and get your hands on a Haynes auto repair manual for your car wish you the best of luck michigan Man.

Posted on Sep 12, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What would cause a fuse to blow out as soon as the battery is plugged in?


If problem on wiring circuit somewhere, replacing the parts won't fix it. If fuse 17--10 amp that fuse circuit is hot all the time. You have a short. Disconnect the wiring connector from generator, does the circuit still go to ground. Instead of blowing your fuses, use a test light across the fuse terminals, if the lite comes on, the circuit is still going to ground. Some don't like to use test lite for that test, but, anyway.
Could be problem with fuse box or the wire circuit from fuse to generator. Make sure generator wire connector doesn't show any signs of heating/melting or anything.
If you think the problem is the white wire with black tracer, you might leave a pigtail wire at both ends, hopefully the pigtails are good, then splice in a new wire for testing. If that fixes it, then make the new splices permanent and route the new wire properly.
generator 1-mgkxnf303xgr2hvssd3liypr-1-0.jpg

generator 2-mgkxnf303xgr2hvssd3liypr-1-2.jpg

May 06, 2017 | Ford Cars & Trucks

1 Answer

2005 ram 1500 wipr fuse keeps blowing with the motor plugged off....fuse #8


Shorted wiring in harness ? Unhook battery check resistance from fuse to ground should be open with motor unplugged and no battery hooked up.

Apr 25, 2017 | Cars & Trucks

1 Answer

My pcm came unplugged without the battery unhooked on a 96 gmc jimmy now wont start


I don't know what you mean by, "I plugged it back up". Did you mean that the harness unplugged or that a wire came out of the plug? Inspect the fuse-box. Look for a blown fuse. You can try disconnecting the battery for 30 seconds. If the stock stereo has the anti-theft feature, remember to disable it first. If a wire did in fact break away then you will need to do more than just push the wire back into place. Please write back with any questions or status, good luck.

Mar 27, 2014 | GMC Jimmy Cars & Trucks

1 Answer

1999 f150 keeps blowing cigarette lighter fuse


Does the fuse blow even if nothing is insterted into the light housing? May be a shorted woire , or possible the socket assy wires have contacted each other on the back side of the recepticle. On the back of the lighter housing are 2 spade or flat blade connectors. One spade is 12volt battery power which feeds the center of the socket and a spade on the outer of the socket which is a ground. I would start by removing the lighter recepticle and make sure both terminals are in the correct positioned and have not fallen off and made contact with each other. Also once remoced you can unplug and check for battery power and ground at terminal. If you remove the sockjet and unplug and the fuse still blows when you install it there is a short in ther wiring.

Sep 24, 2012 | Ford F-150 Cars & Trucks

1 Answer

I started my 7.3 let it run about 20 mins. went to leave it die.I found glow plug fuse blown replaced and blew again.


Hi, generally it is the fuel heater inside the fuel bowl. You can unplug the fuel heater on the back side of filter housing on drivers side and install the new thirty amp fuse.It should start, and keep you going. If it's cold where you are you should replace the fuel heater element. I hope this helps!

Nov 28, 2010 | 1997 Ford F350 Crew Cab

2 Answers

How to find a short in my wiring harness for a 1989 honda prelude? The fuse blew and now my tach,gas gauge,clock and blinkers don't work I put a higher amp fuse in and it lasted about 5 days and blew...


at least you know were to start,key on the fuse that blew.and everything controlled by it.i'm assuming that every time you replace the fuse now,it blows .think back before the short,was there any electricial problems,or devices that didnt work.,wires are melted together,or motors are shorted out.putting a bigger fuse in probably burnt a wire open(meaning got too hot and broke)whatever blew the fuse to start with,is most likley where the meltdown is ,start unplugging the things on that fuse,one at a time,remove tail lightbulbs,inspect thre sockets,look up under the dash at the wiring ,your clock,tach.and gas gauge ,are there,observation is almost 90%of trouble shooting anything .fixing it is easy pop the hood spend some time just looking at every thing follow wires make sure they arent melted together ,and are plugged in,just unplugging something and plugging it back in will show problems,things will fall apart.clips will break and hopefully you will see something obvious,shorts are never fun,do you have any electrical background?and know how to use a multimeter .if you do reply ,

Sep 14, 2009 | 1989 Honda Prelude

2 Answers

My car cranks but dont start


you need to make sure its gettin spark and fuel and compression start from thare also plug a scan tool into it so see if all the sensors are working possibley ecu could be fried

Jun 01, 2009 | 1997 Honda Civic

1 Answer

2005 ford mustang


chances are you blew the fuse... look in the engine compartment fuse panel near the battery....

Apr 09, 2009 | 2005 Ford Mustang

Not finding what you are looking for?
1997 Mazda 626 Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...