Question about 1986 Pontiac Fiero

Open Question

Remove starter motor from 6cyl 1986 fiero - 1986 Pontiac Fiero

Posted by on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 3600 Answers

SOURCE: how do I remove the starter motor in my 1986

The other bolt is straight across from the one you pulled out you will need a 6 inch 3/8 drive extension and a wobble socket or a 3/8's swivel to get it out with. be sure to disconnect the positive battery cable at the battery before removing or trying to remove the opposite bolt or it will short and could cause the battery to explode. Rate if this was helpful. here is a picture of the starter so you can see it this is advance auto. 5841283_wrw_16884_thmb.jpg Worldwide Starter Part No. 16884
Reman; with Automatic Transmission; See Test Chart Page # S-4
Warranty LIMITED LIFETIME REPLACEMENT
$79.99
Core Charge $10.00 ?

Posted on Sep 21, 2009

Ad
vortexfuel
  • 1250 Answers

SOURCE: Car: 1986 Pontiac Fiero SE 2.8L v6 The radiator

have a look to this.

http://captfiero.com/fierofiles/Wiring%20PDF%20Files/1986GTSchematics.pdf
I think the cooling senor temp. give the ground to the relay
hope it helps

Posted on Oct 02, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove 1952 Ford 6cyl starter


I think one bolt is on the block side and the other bolt is on the bell housing side against the firewall.

Sep 11, 2014 | Cars & Trucks

1 Answer

Car: 1986 Pontiac Fiero SE 2.8L v6 The radiator


have a look to this.

http://captfiero.com/fierofiles/Wiring%20PDF%20Files/1986GTSchematics.pdf
I think the cooling senor temp. give the ground to the relay
hope it helps

Oct 02, 2013 | Pontiac Fiero Cars & Trucks

1 Answer

Replace window regulator and motor


To replace the window regulator and motor, you will need to remove the door panel, locate the rivets holding the regulator & motor and then drill or grind then off.

A good source for parts is fierostore .com

Hope this helps.

Nov 26, 2010 | 1986 Pontiac Fiero

1 Answer

How do you replace alternator on 1986 fiero gt


Remove negative battery cable. Jack up rear of car. Remove passenger side rear wheel. Loosen A/C compressor tension bolt. Remove A/C belt. Disconnect 2 wire plug and single wire bolted to back of alternator. Loosen alternator tension bolt. Remove alternator pivot bolt from up top of bracket. Wiggle out through bottom.

Reverse for install.

Good luck,

Rebel Faggioli

Oct 07, 2010 | 1986 Pontiac Fiero

2 Answers

1986 Pontiac Fiero V6 2.8L rebuilt..I started it up, within 45 seconds the exhaust manifolds turn bright red and start burning up. I triple checked the timing, it is idling a bit higher than normal still....


That is usually from a clogged catalytic convertor and/or the pre-cat or collector that sits in between the manifold and the cat. If you left the pre-cat on, remove it and see what the result is.

Jun 03, 2010 | 1986 Pontiac Fiero

1 Answer

How to change struts on 86 pontiac fiero


Jack up car.
Remove tires on back.
Remove Nut on top of each strut, located inside engine hatch.
Remove lower bolts from spindle.
Remove strut.
Use spring compressor to remove springs.
Reverse procedure to replace.

Apr 30, 2010 | 1986 Pontiac Fiero

1 Answer

Where is the starter wire connected to?


It runs between the starter and the junction on the engine wall next to the battery (the junction has a bunch of red wires and other wires connected to black connectors with lots of wires and a couple metal bolts that secure some connections together)

Apr 16, 2010 | 1986 Pontiac Fiero

1 Answer

Bouncing RPMs


My car would do the same thing turned ot to be a loose wire at the coil/distributor. there is a plug connector with tow wires one wass loose I crimped the wire no works great

May 04, 2009 | 1985 Pontiac Fiero

1 Answer

Pontiac fiero 2 8 what should i check thats making a knocking sound


If it is coming from your motor...you should be looking for a new motor or a good garage to have that motor rebuilt.

Mar 05, 2009 | 1986 Pontiac Fiero

1 Answer

Fuse blowing


I agree. I would start by inspecting from the tail lights wiring and move up. You will have to remove interior pannels to see the harness.

Dec 11, 2008 | 1986 Pontiac Fiero

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

246 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8560 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...