Question about 1998 Chevrolet Suburban

1 Answer

How to remove steering wheel on 1999 chevy suburban

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 4,336 Answers

This takes a couple of special tools, one for the anti theft and a puller to pull the wheel.

Posted on Sep 12, 2010

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

jimmy nutron
  • 132 Answers

SOURCE: I am looking for the schematics for the steering column on a 1999 chevy suburban

ok there are 2 bolts under the dash 4 on the floor and the yoke your going to have to take off the plastics around the the collum ther are 4 screws and it comes off. there are two sets of electrical clips you will have to take apart you will see a little push clip and pull apart after that it will be free and slide right out. for the steering wheel there are 2 screws behind it that will take off the air bag and un plug it then one bolt and you will need a puller to take it off thats only if you want it.

Posted on Jun 01, 2009

  • 126 Answers

SOURCE: 1999 bmw steering wheel removal

once you get the airbag removed, the wheel is secured to the shaft with a nut. can't remember what size it is, but i remember i didn't have to go out and buy a special socket for it.

Posted on Jan 18, 2009

  • 341 Answers

SOURCE: steering wheel removal

remove cover remomove nut in center then you will need steering wheel puller i think autozone has one on ther loan a tool sheet. just leave deposit bring back your cost $0

Posted on Oct 22, 2008

CaptainKeyz
  • 202 Answers

SOURCE: remove a power steering pump out of a 97 chevy suburban

For step by step instruction, you best pick up the auto repair guide.
Steering pumps, in general, are not very difficult to replace. Pay careful attention to how you take it apart. Use a camera to help you remember how things go.
You will need to remove the drive belt...it rotates all the accessory pulleys, including the steering pump.
The pump should only have two or three bolts holding it on. Make sure you have a hose clamp, or something clean, to catch the steering fluid when you remove the hose.
Make sure not to over or under tighten the hose clamps when reinstalling it. Start snug...then check for leaks, and tighten if needed.
Good Luck.

Posted on Jan 25, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you replace u-joint in steering column of 1999 Chevrolet Suburban


Go to your local after market or dealer and purchase an intermediate steering shaft, be sure to lock your steering wheel before you disassemble.

Mar 24, 2014 | 1999 Chevrolet Suburban

1 Answer

1999 chevy suburban shakes when slowing down to stop and shakes when your at a speed of 55 or more


Have your tires checked out it sounds like there at around. Or possibly you through a counterweight off. Only other thing that I can think of would be the rotors being bad. However the shaking would only happen when you apply the brakes and you could feel it in your steering wheel.

Aug 26, 2013 | 1996 Chevrolet Suburban

1 Answer

1999 chevy suburban horn, does not work, Fuse is good and relay is good. Where is the ground located?


The ground to the horns is the metel bracket on the horn itself that bolt to the frame of the car , also check the contacts for rust or corrosion , also worse case it might be the clock sping behind the steering wheel try pressing the horn while turning the wheel hope this helps good luck

Jan 29, 2013 | 1999 Chevrolet Suburban

1 Answer

HOW DO I CHANGE THE POWER STEERING HOSE. IT IS WET ALL OVER AND LOOKS TO BE LEAKING BY THE RUBBER HOSE AND SILVER CONNECTION 1999 CHEVY SUBURBAN 5.7


You'll need to disconnect that line from the pump, (some metric wrenches will be needed) and disconnect the line at the steering gear box. It may help removing the A/C compressor and the power steering pump and bracket from the motor to get to the line where it attaches to the pump.

Feb 21, 2010 | 1999 Chevrolet Suburban

1 Answer

1999 Chevy Suburban 1500 stuck in 4 wheel drive.


Check the wire harness on the transfer case to make sure it's still plugged in. Check the selector switch in the dash. Check the hub sensor wire harnesses on the front wheels.
Check for error codes through OBD-II connector under the dash.
Good luck.

Feb 14, 2010 | 1999 Chevrolet Suburban

1 Answer

I am looking for the schematics for the steering column on a 1999 chevy suburban


ok there are 2 bolts under the dash 4 on the floor and the yoke your going to have to take off the plastics around the the collum ther are 4 screws and it comes off. there are two sets of electrical clips you will have to take apart you will see a little push clip and pull apart after that it will be free and slide right out. for the steering wheel there are 2 screws behind it that will take off the air bag and un plug it then one bolt and you will need a puller to take it off thats only if you want it.

Jun 01, 2009 | 1999 Chevrolet Suburban

1 Answer

How do I remove the ignition switch on a 1999 chevy suburban?


Ok, start by disconnecting you negative battery cable. From there, wait at least 1 minute to disable your airbag system. You will have to remove the airbag from the steering wheel, it's retained by a couple bolts on the back of the steering wheel. Once you get the airbag out, disconnect the wires to it, and set it aside. Remove the clip that is above the lock nut for the steering wheel, then remove the lock nut. You need a steering wheel puller to pull the steering wheel off. After you remove the steering wheel, you should have access to the turn signal switch.

May 24, 2009 | Chevrolet Suburban 1500 Cars & Trucks

Not finding what you are looking for?
1998 Chevrolet Suburban Logo

960 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8202 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...