Question about GMC Jimmy

Open Question

How do I disable the alarm on my 1996 gmc Jimmy ?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 109 Answers

SOURCE: Freeze Plug Leak on my 1996 GMC Jimmy

It is usually a simple and inexpensive repair.

Posted on Nov 17, 2008

emissionwiz
  • 75235 Answers

SOURCE: 1996 gmc jimmy

MOST LIKELY THE FUEL PUMP HAS FAILED, WHEN U TURN THE KEY TO RUN POSITION DO U HEAR A HUMMING NOISE FROM THE FUEL TANK? THIS NOISE WILL STOP IN ABOUT 5 SECONDS, U CAN HEAR IT BETTER BY TAKING OFF THE GAS CAP AND LISTENING THERE, IF U HEAR NOTHING THEN THE PUMP WILL HAVE TO BE REPLACED.

Posted on Feb 02, 2009

geraldo14200
  • 48 Answers

SOURCE: How do I remove the rear axle to replace the seal 1996 jimmy

You will have to remove the differential cover on the rear end, in the center of the gear cluster you'll have to rotate your axle until it exposes the ends of the axle shafts, push in the axles as far as you can from the brake pad assembly area, then, there this a C clips that slips into a groove on the end of the axle, you'll have to reove the C clip to pull out the axle.

Posted on May 12, 2009

  • 61 Answers

SOURCE: 1996 GMC Jimmy will not shift into overdrive.

4th gear failure is a common problem with this transmission, assuming it is an automatic. You should have the vehicle checked for codes by a qualified repair center with the proper scan tool. Also, check fluid level and condition. More often than not, the trans loses 3rd and 4th gear, as these are working off the same set of clutches. 3-4 clutches apply in 3rd, and when the 4th shift is made the 2-4 band applies giving you overdrive. If you have no engine braking in manual 3rd, you definitely have a mechanical failure, no 4th could be an electrical, or mechanical fault.

Posted on Nov 18, 2009

  • 1114 Answers

SOURCE: My 1996 GMC Jimmy doesn't reverse but acts like its in neutral.

transmission!!

Posted on Dec 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 96 Jimmy is not a passlock security system. it is an aftermarket Viper. How do I disable this?


You'll need to disconnect the wire harness and splice the original wires back together.

Oct 22, 2016 | 1996 GMC Jimmy

2 Answers

I don't have a button and it wont start how to fix 1996 gmc jimmy


If factory alarm, lock drivers door with key, wait an hour should automatically reset, if it's a factory alarm and you have no keypad. Try removing the fuse for the alarm and wait a few minutes and replace fuse and see if it will reset the alarm.
If its an aftermarket alarm system, look under plastic panel below steering wheel for a plastic black box that is about the size of a deck of cards, izip tied or just hanging with a plugin with several different colored wires and unplug it. That will shutdown an aftermarket alarm and vehicle should crank

Sep 18, 2015 | 1996 GMC Jimmy

1 Answer

Alarm Randomly Goes Off


Factory system or added on?

Mar 20, 2014 | 2000 GMC Jimmy

1 Answer

How do i disable the alae\rm system on a 1996 GMC Jimmy


You can fool it into being off all the time by following the bypass instructions on Youtube.

Jan 20, 2012 | 1996 GMC Jimmy

1 Answer

Problem with my 2000 GMC Jimmy, securty light is flashing not allowing me to start my truck' how can i disable the security' can i still cut the yellow wire even though I cant start it


Thanks for choosing FixYa and welcome to the site. You can disable the alarm but you have to make sure it is the right wire and that you ground it. I would advise you to call the dealership and get the code to reset the alarm. Just make sure you have all your vehicle information with you when you make the call.

Apr 10, 2011 | 2000 GMC Jimmy

2 Answers

I ran my key fob thru the washing machine and my wife threw it away. I found one in the junk yard which looks the same but I've been unable to program it. I also disabled the factory alarm system to stop...


Let your other half know that if it happens again, cracking the case, removing the battery and placing it open in a warm place should restore it. If not, buy a jug of distilled water (zero minerals), bathe the fob in it and repeat the drying process.

Jan 03, 2010 | 1996 GMC Jimmy

1 Answer

2001 GMC Jimmy starts when it wants too.


if ur theft light flashes continuiosly then its an alarm problem lock n unlock it w key n try it if not find a lock smith ur key might need programming

Jun 17, 2009 | 2001 GMC Jimmy

2 Answers

Brake light over rear door on 1996 gmc jimmy


1996 GMC Jimmy no brake lite put in 30 amp and it works

Aug 10, 2008 | 1996 GMC Jimmy

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...