Question about 2002 Volkswagen Passat

2 Answers

Crankshaft sensor for vw polo where is the

Crankshaft sensor for vw polo where is the crankshaft sensor located on a vw polo

Posted by on

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 146 Answers

Crankshaft sensor is located on the right side of the cylinder block behind or under the starter. It is fitted into the rear crankshaft oil seal hausing

Posted on Sep 12, 2010

Ad
  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Welcome Back:

    Visited the website for 2 consecutive days.

  • Contributor
  • 1 Answer

AZQ 1.2 engine the Crankshaft sensor is near to the oil dip stick. Follow the tube down towards the sump and you will see a black wired sensor has one bolt. This I think also controls the rev counter and timing of the ignition. From what I have read these can cause problems as does the EGR valve. Check for vacuum air leeks before anything else at the EGR valve at top front of engine with a tube fitted for the vacuum. The Mass air flow is in the throttle body. and the vacuum map sensor is to the left of the engine behind the dip stick fitted onto the air intake manifold. The speedo sensor is on the gearbox right hand lower rear above the drive shaft at back of engine low down facing top side. The temp sensor is to the right side of the cylinder head near /on the plastic thermostat water manifold with the coolant pipes. hope this helps you.

Posted on Jun 29, 2015

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i fix my crankshaft senor of vw polo 1.4


you cannot fix it you have to replace it, but test if first as sometimes its not the sensor it can be a false code.

Jul 17, 2017 | Cars & Trucks

1 Answer

My vw polo 1.4i classic has got no spark what can be the problem ?"


Hi Sheldon it could be s crankshaft position sensor. Or an immobiliser fault. Can you get the car plugged into diagnostics it will save you money in leg long run. Regards Jim...

May 20, 2015 | Cars & Trucks

2 Answers

Polo classic 1.6 engine I replaced rear oil seal and sencer after all vehicle not spark, and injectors not spraying fuel.


The sensor you replaced is the engine speed sensor.There is a special tool that VW uses to align the ring on the crankshaft.If you do not align the timing marks,the vehicle will not start.

Apr 20, 2015 | Volkswagen Polo Cars & Trucks

1 Answer

How to fit crankshaft sensor on a seat Inca crankshaft not a camshaft sensor???


Depends what year earlier ones at teh front of the engine later ones at the back on the flywheel/bellhousing ,its basically a VW polo so it will be the same as some dealers charge 3 times the price for the same piece that you can buy in the VW dealer

Nov 05, 2014 | Cars & Trucks

1 Answer

Diagram to locate the lambda sensor on vw polo 06 plate 1.4 petrol


from the exhaust manifold you have a pipe going down to the first box(cat converter),the lambda probe(o2 sensor) is between these two.looks like a tube sticking out the side.

Oct 16, 2010 | 2012 Volkswagen Polo

1 Answer

Engine speed sensor location, 2001 vw bug


The Engine speed sender is located on the front of the engine block at the level of the crankshaft near to the gearbox bell housing.

Jun 05, 2010 | 2001 Volkswagen Beetle

1 Answer

MY VW POLO SHOWS FAULT CODE ; P0106 ABSOLUTE MANIFOLD PRESSURE SE


this a map sensor, probably just need the sensor replaced, it measurese intake vaccum and adjusts air/fuel mixture accordingly

Oct 07, 2009 | Volkswagen Fox Cars & Trucks

1 Answer

Location of temp.control sensor on vw polo 2002 1.2


Hi rabing

This sensor is located in cylinder head. Depending on engine code, this sensor is also a sensor for tick-over fuel / air mixture. If this is the case there will be 4 wires fitted to it
John

Aug 30, 2009 | 2002 Volkswagen Jetta TDI

2 Answers

2001 vw polo


Dear Customer,

1
check your sensors 1st,all sensors must be good

2
if all sensors are working good than check your engine firing sequence,some times happens when sequence was wrong,

3
check your exhaust and carborator tuning pin that creates the batter combination for firing in bore for batter performance & less emitions ,so check is it ok or not than go to your nearest service center that havad certified mechanics,

till you read this you had solve this problem definatly,

THNX

May 18, 2008 | 2001 Volkswagen Golf

Not finding what you are looking for?
2002 Volkswagen Passat Logo

4,248 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

yadayada
yadayada

Level 3 Expert

78267 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...