Question about 1997 Ford Probe

Open Question

Check engine light on ford probe 1997 - 1997 Ford Probe

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: 1997 ford probe engine fluxuates

Hi jbloco, few things can casue this problem. Basic things first. Check your ignition componants like , spark plugs, wires,cap,rotor(if applicable). If you car runs good off idle then your Idle air control valve might be bad.

Posted on Aug 20, 2008

  • 1 Answer

SOURCE: 1997 ford f150 cyliner 7 misfire

sme problem had to have it put on computer and codes reset

Posted on Feb 05, 2009

  • 137 Answers

SOURCE: check engine light on in a 1997 ford 150

you need to find out what diagnostic trouble code has been set in the computer related to the light being on. you can go to a car parts store and they will usually retrieve the code for free, idea being that you will then buy some parts to resolve the problem. you can but you are certainly not bound to. the federal govt has established guidelines about when the check engine light must be lit, the standard is that if a condition exists that would cause the vehicle to exceed 1.5 percent of emissions for that model of vehicle as built, then the light must be lit. the rules do not prevent the light coming on for other reasons, but it must be lit for that reason. because of that rule alot of the time when the light is on it has something to do with emissions. that can mean that something is going on with O2 sensor, egr valve, couple other things. O2 sensors do fail, the nature of how they operate and where they operate (in the hot exhaust stream) causes them to eventually fail. anyway thing to do is find out what code is set and proceed from there. hope that helps

Posted on Jun 17, 2009

  • 2 Answers

SOURCE: '89 Ford Probe electrical issue

are you wearing your Seatbelt,are your doors closing all the way hatchback ajar ? i only ask as these would be the Dinging sounds your having chances are you have a bad door pin switch which isnt closin the loop as for your Check engine light being its OBD1 you will have to run a scan tool to see what the codes are that are throwing the Intermintent check engine light but as for the dinging it sounds like a Door pin switch thats gone bad try that 1st ....and this is not a solution but it will be close to it and also scans arent that expensive and it beats throwin Money at a problem that could be dont Guess there are at least 60 known Faults if not more that can Trigger that light to come on ....Goodluck

Posted on Sep 25, 2009

  • 7 Answers

SOURCE: 1994 Ford Probe GT 2.5L V6 Engine check light

most likely you have a problem with your vacuum system. the check engine light is mainly for emission problems. it could the MAS airflow sensor as well though...

Posted on Apr 14, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

89 ford probe hesitates when leaving a red light, then runs fine otherwise, fuel filter?


Engine Runs Rough, Stalls, Hesitates on Acceleration, Hard ...

repairpal.com > Problems > Ford > Probe
Ford Probe Engine Runs Rough, Stalls, Hesitates on Acceleration, Hard Starting, Poor Performance. This is a verified problem based on 9 reports. Learn more ...

Starting Problems - 1997 Ford Probe - RepairPal

repairpal.com > Questions > Ford > Probe > 1997 Ford Probe
Dec 5, 2010 - Starting Problems on 1997 Ford Probe ... If the engine runs rough,stalls, hesitates on acceleration, is hard to start, or has generally poor ...

A new misfire/hesitation on accel. Problem.. - ProbeTalk.com Forums

forums.probetalk.com > Tech Section > 2nd Gen (93-97) V6 2.5L

Feb 05, 2016 | Ford Cars & Trucks

1 Answer

1997 ford probe has random starting and burns distributor out every 6 months


loose wiring can cause failure i would try a engine harness out of junk yard

Feb 22, 2013 | 1989 Ford Probe

2 Answers

Heater fan isn't working in my 1997 ford f150 extended cab 4x4


What have you checked so far ?
Fuse - resistor - power at the blower motor ?

Feb 13, 2013 | 1997 Ford F150 Regular Cab

1 Answer

1994 Ford Probe GT 2.5L V6 Engine check light comes on at around 80kmh and engine seems to lose power. Any ideas what may be causing this? MAP sensor? EGR? MAS air flow?


most likely you have a problem with your vacuum system. the check engine light is mainly for emission problems. it could the MAS airflow sensor as well though...

Mar 16, 2010 | 1994 Ford Probe

1 Answer

Hello, my 1997 ford probe overheated and now it wont start, would you know the possible reasons why?


Duh. The first and most probably reason is that you fried the engine. Take it to a mechanic.

Nov 25, 2009 | 1997 Ford Probe

1 Answer

1997 mustang rear running lights dont work front


assuming you have brake lights and marker light, I would check the socket for voltage, both the contacts and probe the wire (Brown) for voltage...it could be a bad socket.... if no voltage, trace the "Bwn" wire back and keep probing til you find voltage, check the connector in the trunk on the LT/RT side also...hope this helps you...GL

Jul 08, 2009 | 1996 Ford Mustang

1 Answer

How to set timing on 97 ford probe gt


This is the specs...not too sure on what else you are asking about:

d23bf61.gif
Save to desktop and then zoom.

Jun 23, 2009 | 1997 Ford Probe

1 Answer

How do you set the timing marks on 97 ford probe?


what marks are used when setting timing on 1997 ford probe

Oct 19, 2008 | 1997 Ford Probe

1 Answer

Ford probe keeps cutting out when engines hot


its not any thing to do with your air filter its either your thermostat or your radiator check the radiator and see if the over flow reservoir is full, if not then its your thermostat.

Sep 25, 2008 | 1989 Ford Probe

Not finding what you are looking for?
1997 Ford Probe Logo

Related Topics:

110 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5467 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...