Question about 2006 Infiniti Q

1 Answer

Change out gears

I have an Infinity Q-45 1992 I love my baby and this is what is going on..
My transmittion is taking a long time to change out gears from first to second. Its just had a fluid change this weekend and still no luck.. any suggestions?

Posted by on

  • Anonymous Jun 29, 2008

    change fluieds put gas treatment in



1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 375 Answers

Check and see what type of fluid they put into your tranny....I think late model Nissan/Infiniti transmissions use a slightly different fluid from other cars.

Posted on May 14, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

Transmission Problem?

No reverse is the most classic sign of a failed transmission.

May 02, 2017 | Isuzu Trooper Cars & Trucks

3 Answers

My doors do not lock when I put the truck in gear. I also cannot use the lock button on either of the front doors to lock the doors, nor does my remote keyless entry lock or unlock the doors. Also my...

Battery Disconnect or Replacement Problems

Your going to have to take it to the dealer an have thing's reprogrmmed !
Important: Up to 4 transmitters can be programmed. Do not operate or program the transmitters in the vicinity of other vehicles that are in the keyless entry program mode. This prevents the programming of the transmitters to the incorrect vehicle. The order in which the transmitters are programmed is important. The first transmitter programmed will be transmitter #1, and the second transmitter programmed will be transmitter #2. Use care to program the transmitters correctly.
Important: All key fobs must be programmed each time any one fob is programmed. The scan tool must stay connected until all of the transmitters are programmed.
Install a scan tool and navigate to the BCM Module Setup menu.
Select Program Key Fobs.
Follow the scan tool on-screen directions.
When the programming operations have completed, operate the transmitter functions to verify correct system operation

Jun 09, 2017 | 2005 Chevrolet Colorado

1 Answer

How to change gear shift cable on 2001 dodge dakota 2 wheel drive

the cable goes from the shifter to the transmittion arm,, both cable ends connect via a pin and cotter key (usually) the cable housing (black outside layer) is connected to the shifter frame usaually by a clip and is bolted to the transmittion with a couple bolts on the other end ,, i know this was pertty basic but hope it helped

Mar 28, 2010 | 2001 Dodge Dakota

1 Answer

How do I program or fix the key-less entry remote on my Expedition 1998 4.6? I tryed but the truck wont go into programing mode.

This is the procedure to Replacing lost transmitters

Take all your vehicle's transmitters to your dealer for reprogramming if:
1.- One transmitter is lost, or
2.- You want to purchase additional transmitters (up to four may be

To reprogram the transmitters, place the key in the ignition and switch from OFF to ON eight times in rapid succession within 10 seconds. After doors lock/unlock, press any button on all transmitters (up to four).

When completed, switch the ignition to OFF. All transmitters must be programmed at the same time.

Hope thie help (remember rated and comment this). Good luck.

Mar 23, 2010 | 1998 Ford Expedition

1 Answer


it sounds like something wrong the transmittion or u have a wire going to transmittion that is broken try checking those things out

Nov 05, 2009 | 1998 Pontiac Grand Am

1 Answer

1971 dodge challenger timing specs.

Man I love that model! Always wanted one... Take care of that baby! You didn't say what engine you had. I'll sure try to help if you get back with me.
Till then,

Oct 15, 2009 | Dodge Challenger Cars & Trucks

1 Answer

I got a new transmission put in my 1997 honda prelude. now when it shifts it pushes its rpms so high that it jerks into every gear! its so bad even my passengers notice. if i put the gear into D4 too...

hello, question i need to know in order to help u.
when u fitted box, was this a cable type to help change the gears or is it electronic.
once i know this i can tell you how to rectify or test for a bad transmission.
get back to me.

May 17, 2009 | 1997 Honda Prelude

Not finding what you are looking for?
2006 Infiniti Q Logo

116 people viewed this question

Ask a Question

Usually answered in minutes!

Top Infiniti Experts


Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14398 Answers

Are you an Infiniti Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides