Question about 1995 GMC Suburban

1 Answer


Posted by on

  • lawns2mow Sep 12, 2010

    wire on, freon good, fuses good, magneto has ohm reading


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 47 Answers

Did you remember to plug the wires back into the clutch?
If you lost any refrigerant during the process, it could be low now. Also, check the fuse for the AC.

Posted on Sep 12, 2010

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

We have just swapped out a cat engine 3406b and replaced with another, the clutch is not engaging and we have not seen this problem on an eaton fuller clutch before after an engine change out can you...

Re position the clutch point so that it has less than 1/4 inch clearance from engaging the clutch throwout bearing

Or the clutch fork has fallen off the thowout bearing on assembly

Aug 25, 2014 | Cars & Trucks

1 Answer

Car turns off when engaging clutch to a lower gear

Check the following:
- Thrust bearing, clutch.
TEST: Pull up the hand brake. Start the engine and let it at idle speed.
Depress the clutch pedal, put the car in 1st gear, while keeping the clutch pedal depressed. If the gear lever hesitates or produce any abnormal noise, replace the clutch thrust bearing.
- If the gear lever shifts smoothly, clean the throttle body, idle air control valve and perform idle speed learn learn procedure.
- Check the valve clearance.

Apr 11, 2014 | 1992 Toyota Corolla

1 Answer

Replaced air conditioning system. air compressor not engaging, clicking noise coming from compressor. Any ideas?

if the compressor is clicking the clutch is engaging or trying to could be slipping clutch or belt or comp is out of freon or no good

Oct 21, 2012 | 2006 Pontiac G6

1 Answer

Ac clutch not engaging on a 2004 ford escape

A mechanic would check for voltage at the fuse and relay, and also check the system to see if it is full of freon. If the clutch has voltage and ground it may need to be replaced.

Jul 30, 2012 | Ford Escape Cars & Trucks

1 Answer

Clutch relaeasing late

Now you have gone off and confused me. Is it RELEASING late or is it ENGAGING late? Releasing at the top of the pedal is releasing early and engaging late. When you replaced your clutch, did you resurface or replace the flywheel? Makes a BIG difference. I usually recommend master cylinder replacement at the same time the clutch, pressure plate, nflywheel, throwout bearing, pilot bushing or bearing and slave cylinder is replaced. That is the only way to guarantee a trouble-free clutch relacement. The original clutches usually last over 100.000 miles (depending on how it is driven) The replacement clutches will not last nearly that long if a COMPLETE job is not done.

I get undersold on my clutch jobs all the time. But I also get many of those customers back when the other shops do a poor job (clutch, pressure plate, and maybe, a slave cylinder) and the car needs a clutch again in just a few months. It has been a LONG time since I have had one of my clutch jobs come back to haunt me. Sometimes you get just what you are willing to pay for.

Apr 14, 2012 | 2001 Pontiac Sunfire

1 Answer

Clutch is not engaging. Where do you check to fluid level? and what type of fluid do I use?

If a clutch is not engaging, you do not have a fluid problem. The clutch mechanism is only used to DISENGAGE the clutch.
If the clutch does not engage, you probably have a worn or damaged clutch plate. If that's the case, either the engine or transmission must be removed so that the clutch can be replaced.

Dec 08, 2010 | 1992 Saab 900

1 Answer

1993 accord ex ac not blowing cold replaced compressor last year freon level ok unit not engaging is there an easy fix?

With the engine turned off, test the a/c compressor clutch by applying 12 volts to the contacts. You should hear a click of the clutch engaging, and if not, the clutch is acting erratically.

Aug 21, 2010 | 1993 Honda Accord

1 Answer

I replaced an AC clutch. I tested it with lead wires, it engages. When I plug it in with the AC on it will not engage. I have 13 volts to the plug with AC on. what would keep the clutch from engaging if I...


Here to understand why it’s not engaging first check the electric system, fuses, circuit breaker, and connection to the clutch assembly. Chances are your refrigerant level is low and the low pressure cut out switch is preventing the clutch from engaging in order to protect the compressor. You can jump across the terminals at the overload fuse to check operation of the clutch but only for a short period of time in case your system is low on oil. Evacuate and recharge the system to resolve the issue.

Let us know if you want to know something else accept the suggestion.
Thanks for contacting

May 26, 2010 | Ford Mustang Cars & Trucks

1 Answer

1997 Dakota 3.9L A/C Clutch not engaging. I have

if you have power to the clutch and the R134 is full and you are sure of this then the clutch is bad it needs to be replaced.

Jun 23, 2009 | 1999 Dodge Dakota

Not finding what you are looking for?
1995 GMC Suburban Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts


Level 3 Expert

75797 Answers


Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides