Question about 1999 Isuzu Rodeo

Open Question

How do I replace a combination switch (turn signal in the steering column) on a 1999 Isuzu Rodeo

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
ndguy2481
  • 251 Answers

SOURCE: Replace multifunction switch on Pontiac Gran Prix 2000

no just the top and bottom of the steering wheel cover

Posted on Dec 07, 2008

Ad
  • 1 Answer

SOURCE: I need to locate and replace the multi function switch

My turn signal flasher was located to the right of the ash tray, I looked around the column for HOURS and it wasn't there... I also have an 93 oldsmobile cutlass ciera, it drove me crazy because the manual wasn't correct.

Posted on Mar 22, 2009

cadman000
  • 607 Answers

SOURCE: need to replace turn signal switch 93 cadillac deville

First do you have a sterring wheel puller. Can't remove the steering wheel without one. Quite an involved job including snaking the electrical connector end through the steering column. I wouldn't recommend it to the novice

Posted on Mar 29, 2009

  • 22 Answers

SOURCE: replacing the power steering pump on a 1998 isuzu rodeo

Remove low pressure and high pressure hoses (this one could be hard to break loose). You might want to have an oil pan handy, to capture the oil. Disconnect electrical sensor. Remove the bolt that holds belt tension adjustment plate. And finally remove the bolt that holds the pump in place. It is bolted from the back and located at the right lower corner of the pump if you are facing the front of the car. Remove the pump assy. I could not remove belt pulley at home, no matter how hard I tried. Ended up taking it to an automotive shop and they removed it in no time, using one of those "pneumatic impact guns". Assemble new pump. Fill the reservoir with PS oil. Make sure both of the front wheels are off the ground, start the engine and slowly spin the steering wheel back and forth for about 5 minutes or untill screeching sound stops and the liquid in the reservoir stops foaming. That will bleed any air that is in the system. Don't go all the way to the end of stroke. Good luck.

Posted on May 09, 2009

junmag
  • 175 Answers

SOURCE: brake light issue.

the brake lights switch of the expedition is connected to the cruise control system. get yourself a wiring diagram and sort out the problem. i have read of fires being caused by that problem so be carefull.

Posted on May 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Combination switch location


Combination Switch?
You mean turn signal/hi-beam/hazard combination switch?
located on the steering column - is part of that turn signal lever
remove the covers on the upper column and the switch is attached from the side. do not need to remove steering wheel - will however need torx screwdrivers

Oct 11, 2014 | 1996 Dodge Stratus

1 Answer

My hazard lights work, on my 1999 expedition xlt, but my turn signal lights do not. Im not sure if I need to replace the flasher or the relay. If its the flasher, where is the flasher located and where...


This is a common problem for the turn signal switch itself. Try used. You will notice in the instructions to remove the steering wheel. Don't. The removal of the ignition switch is also not necessary. Remove the screws at the bottom of the column where it shows and take a screw driver and pry the other side up to see the 2 screws (torx, or star bits) to remove. This will only take about 20 minutes to perform.

  1. Disconnect the negative battery cable.
  2. Remove the 4 retaining screws from the lower column shroud and remove the upper and lower shrouds.
  3. Remove the 2 retaining screws from the multi-function switch and unplug the 2 wiring connectors.
  4. Remove the switch.

To install:
  1. Install the multi-function switch.
  2. Tighten the 2 retaining screws and attach the 2 electrical connectors.
  3. Install the upper and lower column shrouds. Tighten the 4 retaining screws.
  4. Connect the negative battery cable.

F-150, F-250, Expedition, Navigator and 1999-00 Super Duty Models


0900c152801e597e.jpg

Fig. Fig. 1 Turn the ignition switch to the RUN position and push the lock cylinder release pin with a suitable punch while ...



0900c152801e597f.jpg

Fig. Fig. 2 ... pulling out the lock cylinder



0900c152801e5980.jpg

Fig. Fig. 3 Remove 3 steering column shroud retaining screws and ...



0900c152801e5981.jpg

Fig. Fig. 4 ... remove the upper and ...



0900c152801e5982.jpg

Fig. Fig. 5 ... lower steering column shrouds



0900c152801e5983.jpg

Fig. Fig. 6 Remove the switch retaining screws, lift the switch assembly up and ...



0900c152801e5984.jpg

Fig. Fig. 7 ... detach the switch electrical connectors to remove the switch

  1. Disconnect the negative battery cable.
  2. Remove the ignition key and tumbler as follows:
    1. Turn the ignition switch to the RUN position.
    2. Push the lock cylinder release pin with a suitable punch while pulling out the lock cylinder.

  3. If equipped, twist off the tilt wheel handle and remove.
  4. Remove 3 steering column shroud retaining screws and remove the upper and lower shrouds.
  5. Remove 2 self-tapping screws that retain the combination switch to the steering column casting. Disengage the switch from the casting.
  6. Detach the electrical connectors, being careful not to damage the locking tabs and the shift position indicator cable.

To install:
  1. Connect the combination switch electrical harness connectors ensuring that the connectors are fully engaged. The wiring for the switch is to be routed under the shift position indicator cable.
  2. Install the combination switch with 2 self-tapping screws. Tighten to 19-25 inch lbs. (2-3 Nm).
  3. Install the upper and lower steering column shrouds. Install the retaining screws and tighten to 9 inch lbs. (1 Nm).
  4. If equipped, install the tilt wheel handle ad tighten to 44 inch lbs. (5 Nm).
  5. Install the ignition key and tumbler assembly.
  6. Connect the negative battery cable.
  7. Check the steering column and combination switch for proper operation.

Feb 12, 2011 | 1999 Ford Expedition

1 Answer

Replacing turn signla electronic flasher for 1999


Get the proper flasher from the parts store and start searching under the dash for the one that clicks when the turn signals are operating.

Aug 03, 2010 | 1992 Isuzu Rodeo

1 Answer

I need instructions on replacing a turn signal switch. Our current turn signal is no longer returning or cancelling.


For Caravan, Grand Voyager, Town and Country, Voyager, 2000-2004 check this guide for change Turn Signal Switch:
CAUTION The Supplemental Inflatable Restraint (SIR) system must be disarmed before working around the air bag or SIR system wiring. Failure to do so may cause accidental deployment of the air bag, resulting in unnecessary SIR system repairs and/or personal injury.
  1. Disconnect and isolate the negative battery cable from the battery.
  2. In order to disarm the air bag system, allow the system capacitor to discharge for at least 2 minutes, before performing any removal procedures.
  3. Remove the upper and lower steering column shrouds.
  4. Disconnect the electrical connector from behind the combination switch.
  5. Remove the mounting screws securing the combination switch to the steering column adapter collar.
  6. Remove the combination switch from the vehicle.

    7e690ec.jpg
    Fig. The turn signal (multi-function) switch is attached to the steering column by two screws

To install:
  1. Install the combination switch to the steering column adapter collar. Tighten the combination switch mounting screws.
  2. Reconnect the electrical connector to the combination switch.
  3. Install the upper and lower steering column shrouds and tighten the retaining screws.
  4. Reconnect the negative battery cable and check all functions of the combination switch for proper operation.

Hope helps (remember rated this).

Jul 01, 2010 | 2002 Dodge Grand Caravan

1 Answer

'94 Rodeo right turn signals not working unless using hazards


sounds like a switch problem in the steering colum, could be a bad switch could be a loose connection. my advice would be to purchase a auto repair manual for you vehicle for detailed instruction on testing and/or replacing the switch.

Feb 14, 2010 | 1996 Isuzu Rodeo

1 Answer

No turn signals,dash doesn't work


First check the fuses for signal/hazard lights; From Park Lamp Relay, check the fuse 2 and fuse 3 (15 AMP)

Second, check the "flasher" for signal lights;

For last, review your Turn Signal Swtich:
  1. Disconnect and isolate the negative battery cable from the battery.
  2. In order to disarm the air bag system, allow the system capacitor to discharge for at least 2 minutes, before performing any removal procedures.
  3. Remove the upper and lower steering column shrouds.
  4. Disconnect the electrical connector from behind the combination switch.
  5. Remove the mounting screws securing the combination switch to the steering column adapter collar.
  6. Remove the combination switch from the vehicle.
8344d1d.jpg


To install:
  1. Install the combination switch to the steering column adapter collar. Tighten the combination switch mounting screws.
  2. Reconnect the electrical connector to the combination switch.
  3. Install the upper and lower steering column shrouds and tighten the retaining screws.
  4. Reconnect the negative battery cable and check all functions of the combination switch for proper operation.

You can get more details and wiring diagrams in Autozone.com (free register). Good luck.

Sep 15, 2009 | 2002 Chrysler Town & Country

1 Answer

2001 Isuzu rodeo turn signal switch. How hard is it to replace? The turn signal lever is broken and needs to be replaced.


Not a big job. Start with the plastic mouldings around the steering colum then the four star screws on the bottom of the steering wheel for the airbag unplug the air bag wires unscrew the big nut holding the steering wheel pull off the steering wheel unscrew the cluster unplug and replace.

Aug 05, 2009 | 2001 Isuzu Rodeo

1 Answer

Truck turns wide


your CV joints are worn, not a hard job.. easier to see a mechanicf tho, not too expensive

Jan 07, 2009 | 1999 Isuzu Rodeo

1 Answer

99 Rodeo Right turn signal makes brake lights blink


TURN SIGNALS WILL FEED BACK THROUGH THE TURN SIGNAL SWITCH.THEY ARE INDEPENDENT OUT SIDE ON THE CAR BUT NOT IN THE SIGNAL SWITCH.REPLACE THE SIGNAL SWITCH

Jan 02, 2009 | 1999 Isuzu Rodeo

1 Answer

94 isuzu pickup


i had the same problem with my 1994 rodeo. it is the turn signal switch itself that is bad, I was lucky enough to find the whole switch in a salvage yrad, and replace it, it did the trick, there is a little brass flapper that is supposed to make contact that gets corroded and won't make the contact. one might use dielectric pray into the opening of the switch arm first before you take the steering wheel off and disassemble it.

Aug 25, 2008 | 1992 Isuzu Rodeo

Not finding what you are looking for?
1999 Isuzu Rodeo Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14384 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...