Question about GMC Sierra 1500

1 Answer

How do i get the fan off so i can replace the water pump on my 1996 gmc 1500 pick-up

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 47 Answers

If it's attached to the water pump, there should be @4 bolts holding the clutch to the pulley.

Posted on Sep 12, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1996 gmc 1500 burns gas real fast ,shakes bad in drive,doesnt pick up speed well at take off thanks


When was your last tuneup? Could be minor or major depending on your past maintenance. FI ? Fuel pump, Filter, Regulator, ECM. Need to have someone check your computer codes.

Nov 09, 2013 | Cars & Trucks

1 Answer

Where is the oil pump on a 1996 dodge 1500 pick up


The oil pump is located inside the oil pan, it is bolted to the center main bearing cap of the crankshaft. To replace it you must raise the engine off the mounts and then remove the oil pan.

Sep 29, 2011 | 1996 Dodge Ram 1500 Club Cab

1 Answer

1996 gmc 1500 pu. have replaced fuel pump twice in 2 weeks, runs fine for a few days and than will not start.


Why are the pumps being replaced? are the connectors OK, they are famous for melting where the harness connects to pump at top of fuel tank.

Nov 12, 2010 | 1996 GMC Sierra

1 Answer

How do you replace the water pump on a 1996 dodge ram 1500 with a V8 engine?


remove then neg battery terminal. remove the serpitine belt. remove the fan clutch assembly. remove the fan shroud. remove the altinater and a.c pump. remove the alt and a/c pump bracket. remove the heater hose and inlet pipe. remove the intake manifold cooling hose. remove the lower radiator hose from the pump. finally unbolt the pump and remove. be sure and drain the coolant first. hope this helps

May 31, 2010 | 1996 Dodge Ram 1500 Club Cab

1 Answer

Need to know how to take off a fan blade from a water pump ...off a 1996 gmc jimmy


It's pressed in place and shouldn't be dismantled. If a blade of the pump is damaged you must replace the entire pump.

Feb 13, 2010 | 1996 GMC Jimmy

2 Answers

I have a 1996 gmc 1500 pick up. When push button for 4x4 high it blinks and no 4x4. But 4x4 lo engages, I am stumped. I hear a relay clicking but like I said no 4x4 high


TRANSFER CASE MOTOR ONLY WORKING IN ONE DIRECTION 4WHEEL LOW, HAD A BLAZER WITH SAME PROBLEM REPLACED TRANSFER CASE MOTOR.

Jan 27, 2010 | 1996 GMC Sierra

1 Answer

Need to replace the water pump on a 1992 gmc pick-up need diagram of how to replace do I need to pull the fan cluch and radiator to get to it???


hi,first off you have to remove the acc. drive belts, ac,alt.,pwr str belt etc.but loosen up the 4 bolts that hold the fan to the water pump.then remove any brackets 4 bolts hold the water pump in place and remove water hoses before removing pump bolts. clean and replace gaskets and pump reinstall all parts and added coolant .also you may want to replace thermostat.

Oct 23, 2009 | 1992 GMC Sierra K1500

1 Answer

Pulling a fan clutch assembly from a GMC 4.3 water pump?


First remove the fan from the clutch. There should be four to six bolts holding the fan to the clutch. The clutch is held on to the pump with four bolts. remove the four bolts to remove the clutch. I've included a pic of the pump to indicate the four mounting holes. Not sure if the link will work.

http://www.1aauto.com/scripts/view_full_image.php?image_url=http://images.1aauto.com/EWP/1AEWP00011.jpg&description_id=1090439

Aug 10, 2009 | 1996 GMC Sonoma

1 Answer

How to remove a 2003 GMC Sierra 1500 water pump


first what you want to do is locate the water pump. then release then tension off the belt that it is connected to. there should be 2 or 3 bolts and undo them and pull it out. then replace with the new one.

Apr 29, 2009 | 2003 GMC Sierra 1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

90 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...