Question about 2000 Eagle Medallion

1 Answer

1993 eagle medallion strater problems

The starter was going bad on my eagle, hit and miss starting. I replaced the starter and the rotor.
Now the starter is working fine, but the car won't turn over and start.
The battery is new, so I know thats not it. Any ideas?

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 375 Answers

Explain your meaning of:

won't turn over and start.
Can you hear the starter motor running but the engine is not physically cranking the engine as opposed to the engine actually starting up and running ?.

Or dose the starter just make a grinding noise and is not moving the engine ?

Posted on May 14, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

93 eagle talon standard wont start

Sorry to hear that. First thing I would do is put the transmission in neutral and make sure the engine is turning (by hand) and not locked up. Put a socket on the crank pulley bolt and turn at least one full revolution. Jack up one or both rear wheels and check they spin freely. If wheels are locked, loosen the cable adjustment for the e-brake. Hope you find it, and good luck.

Jul 26, 2013 | 1993 Eagle Talon

1 Answer

I have a 1991 jeep yj - when I turn the key everything powers up as it is suppose to - but the engine does not crank ( I do not hear the strater clicking or anything) I thought it might be the ignition key...

i had one do the same thing, the wire ends at the starter were frayed and the starter had a drag in it, put new ends on starter and replaced the solinod and it worked fine, there is also a fuse that will stop the ignition from working , worth a look to see if its loose or bad contact.

Aug 14, 2011 | 1993 Jeep Wrangler

2 Answers

Turn Key and nothing but lights and radio are fine. No sound of cranking over, is it the strater?

Hello: If the security light is NOT blinking when you hold the key in the start position then it could be the starter, If no security light blinking have a helper hold the key in the start position and the another person hit the starter with a hammer, medium blow, if car starts you have a failed starter. If security light is blinking with key in start then you have a immobilizer problem and you will need the failure code so you will know where to start your diagnosis.

Aug 01, 2011 | 1998 Cadillac Catera

2 Answers

Not strater

kinda need to know more, if the engine won't tern over then it's the starter ore the starter silinoid

Jun 05, 2010 | 1993 Nissan Altima

1 Answer

We need to replace the strater solenoid. any tips?

On this make I it is connected to the starter. You need to remove starter from vehicle. It is the solenoid on the side of the starter.

May 03, 2010 | 1993 GMC Suburban

1 Answer

Will not start battery is good

have starter checked, may be bad, also you can try tapping on starter while someone holds the key in the crank position,tap with a hammer lightly sometime that gets starter going, to test use a test light while key is held in crank see if you get power to small wire on starter, if you get power replace strater. hope this helps.

Nov 27, 2009 | 1998 Ford Windstar

1 Answer

Starter problem renault 21 (medallion) 1991

could that the starter is failing. . if its a manual car are you able to push start it? or clutch not engaging properly that is not releasing the clutch safety in order to start the car

May 26, 2009 | 2000 Eagle Medallion

1 Answer

1993 eagle talon question

make sure your top dead center on 1st cyc. then start your wires number 1 pointing at cyc1 then follow process 3,4,2 and make sure rotor button is with the first plug of course.

May 22, 2009 | 1993 Eagle Talon

1 Answer

93 eagle talon 1.8 won't start

compression. have it compression tested.

Sep 22, 2008 | 1993 Eagle Talon

2 Answers

Have to hit starter 2 or more times before starts - have replaced ignition module, fuel pump, throttle control, idle sensor / once warmed up, starts first hit, problem when cold ????? what are we missing ...

Bad starter? You shouldn't have to hit the starter for it to work, if there isn't anything wrong with it. Sounds like you've replaced everything except the problem.

Jul 25, 2008 | 1997 Oldsmobile Aurora

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

138 people viewed this question

Ask a Question

Usually answered in minutes!

Top Eagle Experts


Level 3 Expert

77544 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Stewart Dibbs

Level 2 Expert

355 Answers

Are you an Eagle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides