Question about 2003 Ford Expedition

1 Answer

Why when i got my a/c knob on the on position my vehicle crancks strong a few times before it start and if i turn the knob to off position it will start right away ?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Contributor
  • 613 Answers

Sounds like its becuase you are getting less current to the ignition when ac off

Posted on Sep 12, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hard crancking when i fill the tan


run fault codes to check for faults in the canister solenoid /servo system

Nov 09, 2013 | 2003 Hyundai Accent

1 Answer

How to reset my security or antithef ligth on escalade 2004 wont start or cranck


Try this it works on an 2002 with the master key take and turn the key on wait about ten minutes the antitheft light will go off then switch the key to the off position wait 5 seconds and turn back to the on position do this 3 times total. On the 3rd time switch the key off then start the vehichle. It may take a few trys of reprograming to get it to work it takes about thirty minutes to do.

Oct 08, 2013 | Cars & Trucks

1 Answer

Vehicle starter won't cranck


I would have it towed back to the shop that did the repairs.
Could be a wiring problem between the starter and the key switch.

Sep 14, 2012 | 2010 Chevrolet Cobalt 1LT

1 Answer

How to change shift knob on 1995 jeep grand cherokee


If this is an Automatic Floor Shift:
- Secure the vehicle to prevent it from rolling while performing the repair procedure.
- Place the shifter in the low "1" position.
- Using a strong upward pulling motion, remove the shifter knob.

You may need to replace with Salvage Yard Parts, as those parts are going to be hard to find.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Dec 04, 2011 | 1995 Jeep Grand Cherokee

1 Answer

I have a 97 saturn that wont start. due to my alarm. it does unlock but it does not start or even cranck..


If this alam was installed aftermarket, most of the time they hook up a relay in start wire just below steer colum inside car- most of the time you can see a wire which was cut to be interrupted through relay to prevent starter from working, if relay or connections fail, vehicle will not turn over

Jan 24, 2011 | 1997 Saturn SC

1 Answer

When purchased, upon starting the car, the radio (manufacture model) volume knob would actually be turning down when you were turning the radio knob up, and it did the opposite if turning the knob up, the...


sounds like a serious electrical issue there hard to track down could be the computer staarting to go in car the radio could of been hooked up wrong causeing other stuff to short out what year is the car what kind of car

Dec 01, 2010 | Pontiac Grand Prix Cars & Trucks

1 Answer

How to adjust transmission cable to shift right


Hi,

Turn the ignition key in a clockwise direction until it reaches its first position, meaning the position the key occupies before it begins to crank the engine if turned further, then move the transmission's shift knob to the "D" position. Turning the key to this position is necessary to unlock the transmission's shift knob. The engine need not be started to adjust the transmission's cable.

Jack up the vehicle with a shop jack, then lower the car onto safety stands to increase the workspace underneath the transmission.

Loosen, but do not remove, the single nut which attaches the end of the transmission's shift cable to the driver's side of the transmission with a wrench.

Position the shift lever on the side of the transmission, where the end of the shift cable attaches to, to the "drive" setting by first rotating the lever in a clockwise direction until the lever stops. Slowly rotate the lever in a counterclockwise direction. As the lever is rotated, it will click. The first time the lever clicks, the transmission is in second gear. The second time the lever clicks, the transmission is in the "drive" position.

Tighten the single nut which attaches the end of the transmission's shift cable to the transmission's shift lever to between 10- and 20 foot-pounds of torque with a torque wrench.

Lift the vehicle with the jack and remove the stands, then lower the vehicle to the ground.

I hope this helps.

Nov 30, 2010 | 1997 Mercury Cougar XR7

Not finding what you are looking for?
2003 Ford Expedition Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...