Question about 2006 Chevrolet Aveo

Open Question

2006 Aveo - windshield wiper fuse blows as soon as it is turned on - even with the wiper motor disconnected at the harness plug. Any help would be greatly appreciated.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 548 Answers

SOURCE: 2006 kia sorento windshield wiper hang up

When you put the wipers on, you positioned them incorrectly so now they go where they shouldn't.
To fix this you need to first make note of which one goes over the other and keep them that way.

Next, put a piece of tape on the windshield where you think they normally go and use that as your target when reinstalling them. Your tape target will probably be 6 -8 inches above the base of the windshield. The wipers should be almost level when at rest.

You'll have to position them with the wiper motor off and in the 'park' position, which means that you turn them on, then turn them off (not with the key) and let them go down to the bottom of the windshield. At that point, you can begin repositioning them.

Good luck!

Posted on Dec 27, 2008

Ad
  • 7 Answers

SOURCE: windshield wiper fuse blows everytime I turn the ignition on

YOU MIGHT HAVE A SORT TO GROUND.A WIRE MIGHT BE LOOSE AND TOUCHING SOMETHING ELSE I WOULD HAVE A PRO TAKE CARE OF THIS PROBLEM

Posted on Apr 07, 2009

dmsr63
  • 2050 Answers

SOURCE: 2006 sorento wipers wont go down all the way when off

The wiper motor has a park mode built in. It's one of two possible problems. The park mode is bad and the motor needs to be replaced. Usually this can be identified by the wipers stopping all over the place.
The second is that the linkage off of the motor has moved, and it will park in the same spot all of the time. Here you need to release the motor to linkage nut, and move the arms to where they should be, and retighten.

Posted on Sep 11, 2009

wracefans24
  • 1985 Answers

SOURCE: windshield wipers keep blowing fuse

it is probably the wiper motor,its building up to much resistance and blowing your fuse

Posted on Jan 26, 2010

Testimonial: "thank you thats kinda what i figured i just wanted someone elses opinion thank you =)"

  • 1374 Answers

SOURCE: 81 corvette Windshield wiper wiring

Hook up an Ammeter in series to the negative battery cable and negative battery post.This way you have full battery voltage during testing .
Then remove the switch for the wipers . Watch the meter once the voltage returns to normal you have found your culprit. If voltage doesn't return to normal do the same for the motor and its relay(I would open up the relay and look it over first)
If all this fails I'll send you the diagram.At that point your on a "Hunt for Red October" I'm out of town currently keep me posted.

Posted on Mar 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is the windshield wiper fuse located in the fuse box on a 06 crown victoria


drivers side inner fender under the hood, look in the owners manual for the number and amps. some are marked under the lid itself

Mar 19, 2015 | 2006 Ford Crown Victoria

2 Answers

Where is the fuse box for the wipers


It is under the dash panel right hand side , kick panel ? Fuse F1.1 10amp . an fuse F1.113 30 amp.
Visual Inspection Chart Mechanical Electrical
  • Windshield washer hoses
  • Wiper linkage
  • Multifunction switch
  • CJB fuses:
    • 1 (10A)
    • 38 (25A)
    • 113 (30A)
  • Circuitry
  • Windshield wiper motor
  • The windshield wipers are inoperative
  • Multifunction switch.
  • Circuitry.
  • Ignition switch.
  • Windshield wiper motor.
  • Go To Pinpoint Test A .
PINPOINT TEST A: THE WINDSHIELD WIPERS ARE INOPERATIVE Test Step Result / Action to Take A1 CHECK CIRCUITS 65 (DG) AND 1002 (BK/PK) FOR VOLTAGE
  • Key in OFF position.
  • Disconnect: Windshield Wiper Motor C125.
  • Key in ON position.
  • Measure the voltage between windshield wiper C125 pin 5, circuit 65 (DG), harness side and ground; and between windshield wiper motor C125 pin 8, circuit 1002 (BK/PK), harness side and ground.
    s3j~tr~en~file=a0039065.gif~gen~ref.gif
  • Are the voltages greater than 10 volts?
Yes
GO to A2 .

No
REPAIR the circuit(s) in question. TEST the system for normal operation. A2 CHECK CIRCUITS 57 (BK) AND 875 (BK/LB) FOR OPENS
  • Key in OFF position.
  • Measure the resistance between windshield wiper C125 pin 6, circuit 57 (BK), harness side and ground; and between windshield wiper motor C125 pin 3, circuit 875 (BK/LB), harness side and ground.
    s3j~tr~en~file=a0037610.gif~gen~ref.gif
  • Are the resistances less than 5 ohms?
Yes
GO to A3 .

No
REPAIR the circuit(s) in question. TEST the system for normal operation. A3 CHECK THE MULTIFUNCTION SWITCH
  • Disconnect: Multifunction Switch C202a.
  • Carry out the multifunction switch component test. Refer to Wiring Diagrams Cell 149 for schematic and connector information.
  • Did the multifunction switch pass the component test?
Yes
GO to A4 .

No
INSTALL a new multifunction switch. REFER to Section 211-05 . A4 CHECK CIRCUIT 57 (BK) FOR OPEN
  • Measure the resistance between C202a pin 4, circuit 57 (BK), harness side and ground.
    s3j~tr~en~file=a0045222.gif~gen~ref.gif
  • Is the resistance less than 5 ohms?
Yes
GO to A5 .

No
REPAIR the circuit. TEST the system for normal operation. A5 CHECK CIRCUITS 56 (DB/OG), 58 (WH), 61 (YE/RD), AND 63 (RD) FOR OPENS
  • Using the following table, measure the resistance between the multifunction switch C202a harness side and the windshield wiper motor C125 harness side:

    Multifunction Switch C202a Windshield Wiper Motor C125 pin 7, circuit 56 (DB/OG) pin 10, circuit 56 (DB/OG) pin 3, circuit 58 (WH) pin 11, circuit 58 (WH) pin 5, circuit 61 (YE/RD) pin 1, circuit 61 (YE/RD) pin 1, circuit 63 (RD) pin 9, circuit 63 (RD)

    s3j~tr~en~file=a0045221.gif~gen~ref.gif
  • Is the resistance less than 5 ohms?
Yes
GO to A6 .

No
REPAIR the circuit(s) in question. TEST the system for normal operation. A6 CHECK FOR CORRECT WIPER MOTOR OPERATION
  • Disconnect all wiper motor connectors.
  • Check for:
    • corrosion
    • pushed-out pins
  • Connect all wiper motor connectors and make sure they seat correctly.
  • Operate the system and verify the concern is still present.
  • Is the concern still present?
Yes
GO to A7 .

No
The system is operating correctly at this time. Concern may have been caused by a loose or corroded connector. TEST the system for normal operation. A7 CHECK THE WINDSHIELD WIPER MOTOR
  • Key in OFF position.
  • Disconnect: Windshield Wiper Motor C125.
  • Carry out the windshield wiper motor component test as described in this section.
  • Did the windshield wiper motor pass the component test?
Yes
The system is operating correctly at this time. Concern may have been caused by binding or incorrect pivot arm adjustment. REFER to Windshield Wiper Blade and Pivot Arm Adjustment in this section. TEST the system for normal operation.

No
INSTALL a new windshield wiper motor. REFER to Windshield Wiper Motor in this section. Hope this helps !

Feb 16, 2015 | 2002 Ford Expedition

1 Answer

KEEP BLOWING THE FUSE AS SOON AS IT IS ENTERED IN THE FUSE BOX.


If you can pull the plug from the wiper motor and try fuse. If no change disconnect the plug to the electric windows and try fuse. Unlikly to be in dome light circut unless you have had aftermarket sterio system or other accessory fitted recently

Nov 28, 2012 | Cars & Trucks

1 Answer

Windshield wiper fuse keeps blowing


Since you Disconnect the motor also renewed the switch and is still blowing the fuse ,it is obvious that you have either broken wire between the switch and the motor. Try to test the failure by means of a tester circuit. Good Luck.

Aug 21, 2012 | 2003 Mitsubishi Diamante

1 Answer

I have checked the wind shield wipers motor to try to find out what is shorting out the fuse. Where could the short be located that is causing the wiper fuse to blow?


You need to isolate the problem by disconnecting the windshield wiper motor. If the fuse does not blow with the wiper motor disconnected the problem is in the windshield wiper motor. If the fuse still blows with the motor disconnected, there is a 12 volt wire shorted to the frame. You will most likely need a set of wiring schematics to trace down the short.

Mar 21, 2011 | Hyundai Accent Cars & Trucks

2 Answers

2005 Ford Escape Front windsheild wipers dont work. whenever the car is turned on the fuse will blow over and over. got the car looked at and was told i need to replace the combo switch. what else could be...


motor may be bad for the windshield wipers, you can disconnect and turn wipers on and see if blows the fuse, as it is in the switch then it should blow as soon as you turn them on. Hope this helps Tim

Oct 19, 2010 | 2005 Ford Escape

1 Answer

How do I fix a short in the windshield wiper line? I think that's the problem. Wipers won't work. Change fuse. Turn wipers on and fuse immediately burns out again. Went through four fuses, even trying...


First of all disconnect the motor before you change the fuse and then try it out. If the fuse blows out hten you have a fault in the line that goes through the harness. If you are not able to isolate the line cut off and use a new line to the motor. However if the fuse stays fine the it is confirmed that your motor is short. You will need to remove the wiper motor unit and check inside for a short in the motor winding or the cummutators. USe a ggood multimeter to see for short and if it has burned then you will need to replace or rewind as acordingly to the cost feasibility. If the motor was stuck due to a damaged spiral gear or the drive wheel replace and proceed. Hope you try this out one by one. Good day

Jul 30, 2010 | 2002 Toyota Sienna

2 Answers

Wiper fuse blows as soon as you insert one


first....be sure the fuse is the right ampage. second...if the ampage is correct, and it still blows, do the following. Disconnect the ground-side of your battery. Attached test lamp to ground-side of battery. Take probe end of test lamp and touch anypart of the motor body frame. If the test lamp (DOES NOT LIGHT UP), you have an electrical short. Recommend OBD (On-board Diagnostic) analysis test.

Apr 25, 2010 | 1998 Subaru Forester

1 Answer

Fuse blows for wiper as soon as i turn on the wiper switch


If you can remove connector to wipers, do it, then turn them on and see what happens. If fuse blows, it's most likely a short in wiring harness, if it doesn't, then most likely the motor. Does it attempt to move at all, before it blows? Look for bad or bare wire in harness as well.

May 31, 2009 | 1999 Dodge Ram

1 Answer

Windshield wiper fuse blows everytime I turn the ignition on


Try removing the harness connector to the motor, and see if it still blows the fuse, then you've isolated the problem.

May 17, 2009 | 1996 Dodge Ram 1500 Club Cab

Not finding what you are looking for?
2006 Chevrolet Aveo Logo

Related Topics:

232 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6924 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...