Question about 1995 Lincoln Mark VIII

Open Question

How to replace rear wheel bearing on a mark 8

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 4369 Answers

SOURCE: rear wheel bearing

SECTION 205-02B: Rear Drive Axle/Differential — Ford 8.8-Inch Ring Gear 2003 Mustang Workshop Manual IN-VEHICLE REPAIR Axle Shaft Removal

  1. Raise and support the vehicle. For additional information, refer to Section 100-02 .
  1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. Remove the rear brake disc (2C026). For additional information, refer to Section 206-04 .
  1. Remove the differential housing cover (4033) and drain the lubricant. For additional information, refer to Differential Housing Cover in this section.
  1. Remove the differential pinion shaft (4211).
    1. Remove the differential pinion shaft lock bolt (4241).
    1. Remove the differential pinion shaft.
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the rubber O-ring in the axle shaft groove.
    Remove the U-washer (4N237).
    1. Push the axle shafts (4234) inboard.
    1. Remove the U-washer.
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Damage to the rear brake anti-lock sensor (2C190) may occur if it is not removed before the axle shaft.
    Carefully remove the rear brake anti-lock sensor. For additional information, refer to Section 206-09A .
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the wheel bearing oil seal.
    Remove the axle shaft.
--------------------------------------------------------------------------------------
Rear Wheel Bearing and Axle Shaft Oil Seal Removal
  1. Remove the axle shaft (4234). For additional information, refer to Axle Shaft in this section.
  1. NOTE: If the wheel bearing oil seal is leaking, the axle housing vent may be plugged.
    Using the special tools, remove the rear wheel bearing and wheel bearing oil seal.
Installation
  1. Lubricate the new rear wheel bearing with the specified lubricant.
  1. Using the special tools, install the new rear wheel bearing.
  1. Lubricate the lip of the new wheel bearing oil seal.
    • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.
  1. Using the special tools, install the new wheel bearing oil seal.
  1. Install the axle shaft. For additional information, refer to Axle Shaft in this section.

-------------------------------------------------------------------
Installation
  1. Lubricate the lip of the wheel bearing oil seal
    • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the wheel bearing oil seal.
    Install the two axle shafts.
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the rubber O-ring in the axle shaft groove.
    Install the U-washer.
    1. Position the two U-washers on the button end of the axle shaft.
    1. Pull the axle shaft outward.
  1. NOTE: If a new pinion shaft lock bolt is unavailable, coat the threads with Threadlock and Sealer EOAZ-19554-AA or equivalent meeting Ford specification WSK-M2G351-A5 prior to installation.
    Install the differential pinion shaft.
    1. Align the hole in the differential pinion shaft with the case lock bolt hole.
    1. Install a new differential pinion shaft lock bolt.
  1. Install the differential housing cover and fill the rear axle with the specified lubrication. For additional information, refer to Differential Housing Cover in this section.
  1. Install the rear brake anti-lock sensor. For additional information, refer to Section 206-09A .
  1. Install the rear brakes. For additional information, refer to Section 206-04 .
  1. Install the tire and wheel assembly. For additional information, refer to Section 204-04 .
  1. Lower the vehicle.

Posted on Apr 10, 2009

Ad
michigan man
  • 3533 Answers

SOURCE: Rear wheel bearings on Hyundai Accent

no i do not believe they are press in there are held in by a seal try www.autozone.com to see if they have your car listed if they do you will be able to get a diagram showing you how they come a part.

Posted on Apr 24, 2009

  • 1 Answer

SOURCE: Rear Wheel Bearing Repair; 2005 pontiac aztek

Remove the brake caliper
Remove the disc, (rotor)
Remove the 34mm nut on the axel shaft
Remove the three (3) bolts from the back side
You will need a wheel puller (three jaw will work well)
Place the puller over the hub and tighten, this will push the shaft out of the hub. Now you have to pull the hub assy. out of the mounting bracket. I found hitting each side,of the hub with a lead hammer to work well. Don't forget to disconnect the ABS senser on the back side of the hub assy.
Do not over tighten the 34mm axel nut when you install the new assy. If you use an impact whrench on it you will damage the bearing.

Posted on May 03, 2009

Mr BrokRench
  • 1623 Answers

SOURCE: I need instructions on how to replace rear wheel bearings on my 1994 Honda Civic

Bearings are pressed into the hubs...much easier, faster and economical (if you don't have a press) to replace the complete bearing/hub assembly, no pressing is needed, since bearings are already pressed into the new hubs. Cost..aprox, 60 buxs each.
Here are the steps for the rear replacement...
Loosen the lug nuts on a rear wheel. 2) Chock the wheels and jack the rear of the car on the side with the lug nuts that you just loosened. 3) Remove the wheel by removing the lug nuts. 4) Pry open the dust cap covering the center of the axle/spindle. A small screwdriver tapped into the space between the hub and dust cap will work well for this. 5) With the dust cap now removed, use a thin center punch to straighten the little dent in the rim of the spindle nut so that you will be able to turn it freely in the next step. 6) Use a 32mm socket and a large breaker-bar to loosen the spindle nut. Unscrew the nut all the way and place it in a clean, safe area. 7) You should now be able to slide the hub/bearing assembly from the shaft. 8) Installation is the reverse of removal. Use plenty of high-temperature wheel bearing grease on all surfaces before you mount the replacement hub assembly.

IMPORTANT: Torque the spindle nut to 134 ft/lbs....(per manual specs)

When reinstalling the dust caps, tap them gently into place to avoid denting them...Install wheels, jack her down and pat yourself on the back...job complete.
Good luck..hope this will fixya up...please take time to leave me a fixya rateing...

Posted on May 23, 2009

  • 119 Answers

SOURCE: Procedure for replacing rear wheel bearings 2000 Forester

i'm assuming you don't have a hubshark,this is a tool that will alllow you to remove the bearing while the knuckle is attached to the car,you may be able to rent this tool at a auto prts store .if not you need to remove the entie knuckle,first remove the trailing arm bolt,then the lateral link bolt{long and stubborn bolt},disassemble the brake shoes and parking brake cable,abs sensor if equipped the knuckle to strut bolt{no marking necessary they are not eccentric} then you need a to use or borrow a press to remove hub and bearings good luck

Posted on Jul 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace rear wheel bearings ?


After taking off the wheel, unbolt the main stud bolt, usually there is a security pin holding it in place. Now you need a puller to remove the first bearing, and the second bearing. After replacing these you tighten up the brake bolt all the way, and turn it back 1/8 to 1/4 turn so that the beake turns easy.

Jul 03, 2015 | 2006 Tata Indica LSi

1 Answer

Wheel bearing


If grinding noise is heard coming from front side, lift up both the front wheels and rotate the wheels one by one to listen to the sound, if any. If a noise is heard, replace the front wheel bearings as a set.
If the front wheels do not produce any abnormal noise when rotated, lift down the front vehicle. Lock the front wheels with blocks, release the hand brake. lift up the rear wheels and try to listen to the abnormal noise. If the noise is heard, replace the differential bearings and seals. Top up the differential oil to the mark.

Dec 12, 2013 | 1998 Toyota Tacoma

1 Answer

Rear suspension sway axle side


could be rear wheel bearings - they come as a complete assy with brake hub - approx $45 each side - 1 hour per side for replacement. Also replace the rear sway bar links $8 for a set - other than that you could have a bent wheel and or loose rear control arm bolts - remove the rear wheels and check all mounting bolts - I had this problem and my rear end felt like it was shimming when I went around corners - 5 minute fix

Oct 27, 2013 | 2000 Ford Focus

2 Answers

Procerure to replace wheel bearing assy 2004 nissan altima 4cyl


Go to YOU TUBE and put in replacing wheel bearing hubs for
nissan altima & watch

There is a lot to see even if on a different vehicle

I doubt you have the tools to do the job

Sep 19, 2012 | Nissan Altima Cars & Trucks

1 Answer

How to change back hub on 97 cr-v


Rear Brake Discs
  • Fotolia.com" data-type="modal">honda-rear-wheel-bearing-removal-1.1-800x800.jpg Replace the bearing and race as a single set. automotive roller bearing. image by Tom Oliveira from Fotolia.com

    Before raising the rear of your Honda, remove the dust cup from the center of the brake drums using a hammer and chisel. This will give you access to the spindle nut, which you can loosen using an axle nut socket. Then you can raise and remove the wheel/tire assembly ,or assemblies if you are replacing the bearings on both wheels.

    If your Honda model is equipped with rear disc brakes, remove the brake disc retaining screws, the brake hose bracket from the steering knuckle and caliper bracket mounting bolts. Hang the caliper to the coil spring using wire. Do not let the caliper hang free or the brake hose may be damaged.

    At this point, you will be able to remove the brake disc by hand. However, rust may have a firm grip on the disc. If this is the case, use a couple of 8-by-1.25 mm bolts and screw them evenly into the brake disc threaded holes. This will push the disc off the hub. Now you can finish removing the spindle nut and hub/wheel bearing assembly and install the new hub/wheel bearing assembly using a new spindle nut



Read more: Honda Rear Wheel Bearing Removal ' eHow.com http://www.ehow.com/way_5974291_honda-rear-wheel-bearing-removal.html#ixzz1W3WDRoqv Rear Brake Drums
  • Fotolia.com" data-type="modal">honda-rear-wheel-bearing-removal-2.1-800x800.jpg Pack the bearing with bearing grease before installation. roller bearing image by Tom Oliveira from Fotolia.com

    If your Honda Civic comes equipped with rear brake drums, remove the center grease cup and loosen the axle spindle nut using an axle nut socket. After raising and removing the wheel/tire assembly, finish removing the axle nut and washer.

    You might be able to remove the outer wheel bearing from the spindle using a screwdriver. If not, wiggle the brake drum as you pull on it to let the bearing fall off the spindle. However, the brake drum might be caught in place by the brake shoes. In this case, you can retract the brake shoes through the hole in the back of the backing plate.

    Remove the rubber plug from the back of the backing plate. Then rotate the star wheel on the adjusting screw using a brake adjusting tool as you push the lever off the start wheel with a screwdriver. With the brake shoes off the brake drum, pull the brake drum off the wheel assembly. Then clean the brake assembly with brake parts cleaner and a clean, lint-free towel.

    Now you can set the brake drum on a workbench or hard surface and remove the grease seal and inner wheel bearing. The inner and outer wheel-bearing races can be removed using a drift punch and hammer. Pack the new wheel bearings with high-temperature wheel-bearing grease using a wheel-bearing packer and use a new grease seal during installation. Also, before reinstalling the brake drum, apply a thick coat of wheel-bearing grease to the cavity inside the hub, but do not fill it completely.



Read more: Honda Rear Wheel Bearing Removal ' eHow.com http://www.ehow.com/way_5974291_honda-rear-wheel-bearing-removal.html#ixzz1W3WN9eBb

Aug 25, 2011 | Honda CR-V Cars & Trucks

1 Answer

Replacing rear wheel bearing. how to remove?


Remove the rear wheel, then the bearing cap. Then remove the split pin out, the crowed washer and bearing nut & washer. Now remove the outer tapered bearing, and the brake disk ...

Aug 15, 2011 | 1997 Audi A4

1 Answer

2wd front wheel need to replace bearings or hub assembly which is best


A Front Wheel Drive Vehicle Can Have Two Types Of Rear Wheel Bearings: Serviceable Bearings, Or Nonserviceable, Sealed Bearings. When Sealed Bearings Fail, The Bolts Holding The Bearing And Hub To The Axel Or Control Arm Must Be Removed. When Installing The New Bearing Assembly, Torque The Bolts To Specifications.Some Manufacturers require The Use Of New Fasteners When Rear Bearings And Hubs Are Replaced.

When A Serviceable Wheel Bearing Is Used, The Bearing Can Be Disassembled And Packed With Grease.It Is Serviced Like A Front Wheel Bearing On A Rear-wheel-Drive-Car.

Apr 09, 2010 | 2003 Ford Explorer Sport Trac

1 Answer

How to change a rear wheel bearing on a 1994 toyota camry


The rear wheel bearing on a toyota camry is replaced by replacing the wheel bearing and hub as a unit. this is a design change as compare to older models with two piece wheel bearings. Scotch drive wheels. Remove rear wheel. Remove rear brake drum. (note: if emergency brakes are applied you will not be able to remove brake drum) Remove dust cap and hub retaining nut. Hub should slide off as unit. Replace hub with new unit. Installation is reverse of removal.

May 30, 2009 | 1994 Toyota Camry

1 Answer

I need instructions on how to replace rear wheel bearings on my 1994 Honda Civic


Bearings are pressed into the hubs...much easier, faster and economical (if you don't have a press) to replace the complete bearing/hub assembly, no pressing is needed, since bearings are already pressed into the new hubs. Cost..aprox, 60 buxs each.
Here are the steps for the rear replacement...
Loosen the lug nuts on a rear wheel. 2) Chock the wheels and jack the rear of the car on the side with the lug nuts that you just loosened. 3) Remove the wheel by removing the lug nuts. 4) Pry open the dust cap covering the center of the axle/spindle. A small screwdriver tapped into the space between the hub and dust cap will work well for this. 5) With the dust cap now removed, use a thin center punch to straighten the little dent in the rim of the spindle nut so that you will be able to turn it freely in the next step. 6) Use a 32mm socket and a large breaker-bar to loosen the spindle nut. Unscrew the nut all the way and place it in a clean, safe area. 7) You should now be able to slide the hub/bearing assembly from the shaft. 8) Installation is the reverse of removal. Use plenty of high-temperature wheel bearing grease on all surfaces before you mount the replacement hub assembly.

IMPORTANT: Torque the spindle nut to 134 ft/lbs....(per manual specs)

When reinstalling the dust caps, tap them gently into place to avoid denting them...Install wheels, jack her down and pat yourself on the back...job complete.
Good luck..hope this will fixya up...please take time to leave me a fixya rateing...

May 23, 2009 | 1994 Honda Civic

1 Answer

Procedure for replacing rear wheel bearings 2000 Forester


i'm assuming you don't have a hubshark,this is a tool that will alllow you to remove the bearing while the knuckle is attached to the car,you may be able to rent this tool at a auto prts store .if not you need to remove the entie knuckle,first remove the trailing arm bolt,then the lateral link bolt{long and stubborn bolt},disassemble the brake shoes and parking brake cable,abs sensor if equipped the knuckle to strut bolt{no marking necessary they are not eccentric} then you need a to use or borrow a press to remove hub and bearings good luck

Mar 22, 2009 | 2000 Subaru Forester

Not finding what you are looking for?
1995 Lincoln Mark VIII Logo

Related Topics:

389 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

fordexpert

Level 3 Expert

5520 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...