Question about 1997 Chevrolet S-10 Pickup

1 Answer

A/c clutch locked up what do i do? - 1997 Chevrolet S-10 Pickup

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 228 Answers

Clutch hub bearing siezed up, was it noisy for some time?
Get an estimate on minimum parts and labor for a beairng relacement or at its best,a new compressor,and hub assembly.

Posted on Sep 11, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Clutch goes to floor but will not go in gear when in gear starts but starts moving with clutch still pushed to floor


Either the clutch needs replacing or the cable needs adjusting.
First thing is to try and adjust it if possible.
Get someone to press and release the clutch pedal while you are looking in the engine compartment and see if you can locate the actuation mechanism. You should see the clutch lever being moved back and forth. Once located and you see which way everything moves, get the person to stop pressing the pedal. On the cable that moves the lever should be 2 nuts (one of which is a locking nut that prevents the the one nearest the lever from moving). Loose of the locking nut off and start tightening the other one up. The person in the car may see the pedal start rising up. Tighten up and try the clutch again. Keep adjusting until it feels okay whilst driving. Finally tighten the lock nut down to the adjusting nut to prevent it from loosening off over time. If there is not enough adjustment possible it may require a new cable.

Feb 15, 2016 | Cars & Trucks

2 Answers

I have been getting the code p0740 it says something about the torque converter clutch circuit. it doesn't seem to be going into over drive. dose anyone have any suggestions I can try.


On some cars, there is a TCC solenoid in the transmission which can be replaced by removing the bottom pan. In some cars this solenoid can't be accessed without major disassembly.

Jun 04, 2015 | Cars & Trucks

1 Answer

Clutch locks up after truck warms up


would suggest have it stripped down now why you still have some use left in clutch you dont want to wait until it locks up completely as may cause more damage

Mar 29, 2014 | 1994 Ford Ranger Supercab

1 Answer

P0740 honda odyssey


P0740 Honda - Transmission Lock-Up Control System Fault Possible causes
- Low transmission fluid level
- Dirty transmission fluid
- Faulty torque converter clutch solenoid valve
- Torque converter clutch solenoid valve harness is open or shorted
- Torque converter clutch solenoid valve circuit poor electrical connection

Tech notes
On some Honda vehicles the P0740 code may be set by an overheating torque converter problem which is caused by an insufficient flow to the torque converter release circuit.

P0740 Honda Description
The torque converter clutch solenoid valve is activated, with the gear in D4, by the Transmission Control Module (TCM) in response to signals sent from the vehicle speed and the Engine Control Module (ECM). Lock-up piston operation will then be controlled. When the torque converter clutch solenoid valve is activated, the torque converter lockup clutch will engage creating a 1 to 1 RPM ratio between the transmission input shaft and the rotational speed of the torque converter.
Lock-up operation, however, is prohibited when A/T fluid temperature is too low.
When the accelerator pedal is depressed (less than 2/8) in lock-up condition, the engine speed should not change abruptly. If there is a big jump in engine speed, there is no lock-up.

Dec 04, 2013 | 2000 Honda Accord

1 Answer

AC Clutch noise and vibration


An A/C clutch will not make this concern happen, more likely the A/C compressor is begining to go out. The belt on the A/C clutch Assy. free wheels (spins feree on the pulley) when clutch is not engaged. If concern is not present with A/C off this means the bearings in the puley assy. ok. Once the A/C clutch is engaged it locks the compressor against the spinning pulley and turn the compressor chaft and spins the A/C compressor internal shaft. If you hear a loud "screach" when you turn on the A/C it means the belt slipped for a second, if it continiues to screach it means either the belt is loose or that the compressor is internaly locking up. I wouild start by checking the belt tension (if not equipted with and auto tensioner). You can also remove the belt and turn on the A/C and attempt to turn the clutch/pulley by hand, it should turn with a little effect but should not bind or lock at times if that happens compressor is bad.

Sep 30, 2012 | 1997 Saab 900

1 Answer

1998 jeep grand cherokee 4x4. have the p0740 code. have to start from neutral, then shifts faily well. May start fluttering and making noise, have to put back to N, then to D and once again will shift. ...


P0740 JEEP - Torque Converter Clutch Circuit
Symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
- Transmission shift shock
- Vehicle may not shift into the highest gear

Possible causes
- Low transmission fluid level
- Dirty transmission fluid
- Faulty torque converter clutch solenoid valve
- Torque converter clutch solenoid valve harness or connectors
- Torque converter clutch solenoid valve circuit is open or shorted

When is the code detected?
Torque Converter Clutch (TCC) unlocked for 10 sec., ECM commands converter lock-up and did not record engine speed drop.

P0740 JEEP Description
The torque converter clutch solenoid valve is activated, with the gear in D4, by the Transmission Control Module (TCM) in response to signals sent from the vehicle speed and the Engine Control Module (ECM). Lock-up piston operation will then be controlled. When the torque converter clutch solenoid valve is activated, the torque converter lockup clutch will engage creating a 1 to 1 RPM ratio between the transmission input shaft and the rotational speed of the torque converter.

Lock-up operation, however, is prohibited when A/T fluid temperature is too low.

When the accelerator pedal is depressed (less than 2/8) in lock-up condition, the engine speed should not change abruptly. If there is a big jump in engine speed, there is no lock-up.

Mar 27, 2011 | 1998 Jeep Cherokee 4WD

2 Answers

What code po741


P0741 "Torque Converter Clutch Solenoid stuck off"
If the PCM detects high torque converter slip when the TCC is commanded ON, then DTC P0741 sets. The Powertrain Control Module (PCM) controls the Torque Converter Clutch Solenoid Valve (TCC Sol. Valve) Pulse Width Modulation (PWM). The solenoid controls the hydraulic fluid for TCC apply and release. When the TCC is applied, the engine is coupled directly to the transmission through the TCC. The TCC slip speed should be near 0.
Thank you for using Fixya and good luck

Aug 05, 2010 | Hyundai Santa Fe Cars & Trucks

1 Answer

EATC Fuse/AC Compressor


yes clutch is replaceable to check if comp is locked turn clutch itsefl not pulley if unmovable by hand replaced comp

Jun 29, 2009 | 1999 Lincoln Town Car

1 Answer

I am looking at a 1992 Nissan Maxima to replace the vehicle I have and my husbands uncle has it. He said that it runs great but when he put it in gear it wouldn't go. Then he shut it off for a few minutes,...


No trans lock. The clutch could be bad or the clutch master or slave cylinders. Check the fluid level in the clutch system resivoir. How does the clutch pedal feel? Is it firm and returning normally?

Dec 28, 2008 | Nissan Maxima Cars & Trucks

1 Answer

Changing the starter


INSPECT OVERRUNNING CLUTCH 1. Slide the overrunning clutch along the shaft. Replace it if does not slide smoothly. 2. Rotate the overrunning clutch (A) both ways. Does it lock in one direction and rotate smoothly in reverse? If it does not lock in either direction or it locks in both directions, replace it. 299a793.gif 3. If the starter driver gear (B) is worn or damaged, replace the overrunning clutch assembly: the gear is not available separately. Check the condition of the flywheel or torque converter ring gear if the starter drive gear teeth are damaged.
CLEANING 1. Do not immerse parts in cleaning solvent. Immersing the yoke assembly and/or armature will damage the insulation. Wipe these parts with a cloth only. 2. Do not immerse the drive unit in cleaning solvent. The overrun clutch is pre-lubricated at the factory and solvent will wash lubrication from the clutch. 3. The drive unit may be cleaned with a brush moistened with cleaning solvent and wiped dry with a cloth. findme(''); findme(''); findme(''); 7d082d0.gif

Jun 07, 2008 | Hyundai Motor 2004 Sonata

Not finding what you are looking for?
1997 Chevrolet S-10 Pickup Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...