Question about Toyota Corolla

1 Answer

How 2 stop reverse beeper - Corolla Toyota Cars & Trucks

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 4,793 Answers

Find the beeper and cut the wire,

Posted on Sep 11, 2010

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Disconnect reversing beeper on transit jumbo 100 t350

I wouldn't recommend disconnecting, it may be a legal requirement.

Mar 04, 2015 | Cars & Trucks

1 Answer

What fuse works the back up beeper

It's probably hooked to the reverse light circuit. See if you have reverse lights, if so then go to where the beeper was wired in and see if they did a good job or a tape job. taped stuff will always develop a problem over time. if you got power to it while in reverse but it ain't beepin-you know what to do.

Jan 30, 2015 | Cars & Trucks

1 Answer

Reversing beeper has constant beep

The easiest possibility is that the proximity sensor thinks something is constantly very close to your bumper. Assuming you don't have any weird stuff hanging off your car that could confuse it, the sensor is likely damaged.

Oct 20, 2014 | 2008 Toyota Camry

1 Answer

How do you disconnect a reverse beeping signal on a 2006 Toyota Sequoia?

I have found the beeper wired into the reverse lights and if you just find the beeper and cut off the wire and cap it you should be fine and no more beep.

May 05, 2014 | Toyota Sequoia Cars & Trucks

1 Answer

2008 Nissan Quest Reverse Park aid stoped working. First sound got funny and then quit. The switch disable light stays on and won't turn back on

replace the beeper that makes the sound when you are in reverse.the light will also go out after you replace thet beeper.

Sep 16, 2012 | 2008 Nissan Quest

1 Answer

How do i know if i have back up sensors

By backup I assume that you mean reversing sensors. Look on the rear bumper (fender) of the car you should see a number of small round disks embedded in the plastic (same colour as paintwork).

This should be them.

If they are there try reversing over the kerb or a small step (just less than max clearance height) the sensors will normally pick this up as you get within about a foot or so and the warning beeper will sound.

Alterately put a large pillow behind the car and reverse toward it. If you hit it without a warning beeper going off you don't have the reverse sensors or they are not working.

Feb 28, 2011 | 2003 Jaguar X-Type

1 Answer

The beep is not working when in reverse how do you fix it on a 2002 celica

If you cant find the beeper at the rear of your car, you could make an easy fix by buying a reverse lamp and beeper combo and replace one of your existing reversing lamps. ie the new lamp has a beeper circuit inbuilt into itself. Any auto shop should be able to sell you one of these or try ebay. That way you aren't relying on a dodgy switch on your transmission selector assembly which is the likely cause. It is possible that the existing beeper is broken or perhaps one the wires has come off. Have a look at removing the tail light assemblies. This is often done via the inside of your trunk area.
Steve (Melbourne,Australia)

May 12, 2010 | 2002 Toyota Celica

1 Answer

I have a 2005 toyota tundra with rear parking sensor that stopped working any trouble shooting ideas?

check the fuse for that circuit.there is a beeper under the dash as well.put a test light on it and see if it flashes,that means the beeper is dead.remove the switch if there is one that turns it off and jumper across it,and check the circuit from the shifter wiring to it,and also the reverse lights,they may have it wired to the reverse lights.

Apr 26, 2010 | 2004 Toyota Tundra

4 Answers

Toyota prius beeper

you cant eliminate beeper yourself but if you taake it to the dealer it being so new they have to hook up the scan tool to turn of your beeper as long as its as factory system i work at a toyota dealer and we do this for cust a lot our computer has all the options in you car that are changeable due to the cust preference hope this helps

Mar 23, 2009 | 2009 Toyota Prius

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts


Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides