1992 Toyota Pickup
Problem for Toyota 1992 Pickup

22RE engine light on, 1992 pickup




By lawyer - usenet poster

" "
22RE engine light on, 1992 pickup, engine will remain running when
going, but quites when I let off the gas to stop or change gears,
something to do with the idle I think. Need help with this problem.
Thanks

Same Problem

Mar 05, 2009

-   elveiclo enciende bien pero cuando se aselera un poco enpesa a fallar y tira por el escape un fuerte olor a combustible-   Guest

Mar 02, 2009

-   hmmm I had this problem just to day.... turns out needed water an oil so my head blew..... wtf I'm screwed so yeah check you fluids first lol. everything was just filled a month ago an no leaks so I didn't think i needed to check it for a bit ooops -   DrinaDi

May 23, 2008

-   how to get the codes of ?
check engine light-   vicferrer

Solution #1

posted on May 14, 2008
Somewhat Helpful)

lawyer

Rank: Apprentice 
Rating: 0%, 0 votes
About half of the ECU codes stored on the first & second generation EFI
Toyotas don't show a constant blinking check engine light therefore you
must pull the ECU codes to see if a fault is registered.

To pull the ECU codes:
All 1980-1995 and including 1995 EFI equipped vehicle allow you to find
engine and related faults by pulling the ECU (computer) codes without
the need for a handheld OBDII diagnosis scanner, the sites listed below
have the fault codes needed to pull the codes and the instructions on
how to do it:
http://autorepair.about.com/library/ts/o...
http://autorepair.about.com/library/ts/o...
http://autorepair.about.com/library/ts/o...
http://autorepair.about.com/library/ts/o...
http://autorepair.about.com/library/ts/o...
http://autorepair.about.com/library/ts/o...
http://autorepair.about.com/library/ts/o...
http://autorepair.about.com/library/ts/o...
http://autorepair.about.com/library/ts/o...
http://autorepair.about.com/library/ts/o...
http://autorepair.about.com/library/ts/o...
http://autorepair.about.com/library/ts/o...
http://autorepair.about.com/library/ts/o...
http://autorepair.about.com/library/ts/o... (auto tranny codes)
http://autorepair.about.com/library/ts/o...
http://autorepair.about.com/library/ts/o...

Pulling the ECU (EFI computer) codes is the first thing I do to
diagnosis a problem thereafter I reset the ECU to see if the same
problems show up and if so I then take voltage measurements at each ECU
wire both with the engine running and not and compare with the factory
service manual, I also close the ignition switch after a cold engine
and also after a warm engine and compare the resistance values with the
factory service manual. This technique will completely isolate your
problem without having to do trial and error and it is the technique I
use when repairing tv's, vcr's, home/car audio.

Sidney?? ???
Repairs tv's,vcr's,home/car audio out of my home
E-mail:
Dartmouth,Nova Scotia
Canada
1985 Toyota 4-Runner,solid front straight axle,factory cruise
control,sunroof,22R-E,W56,RN60LV-MSEK,with 252 000 KM

O
|\ __O
_|_| \
Was this helpful?
Yes
No
1 person thought this was helpful

Solution #2

posted on Jun 19, 2008
Somewhat Helpful)

SLAYER SLY

Rank: Wiz 
Rating: 81%, 68 votes
to check the ecu codes get a jumper wire and cross t1 and te1 also could be t1 or e1 and turn ing. foward count the blinks and refur to chilton or hans manul for codes but if u have not changed the fuel filter try that first
Was this helpful?
Yes
No
1 person thought this was helpful

Solution #3

posted on May 14, 2008
Somewhat Helpful)

lawyer

Rank: Apprentice 
Rating: 0%, 0 votes
The first step in tracking down the problem is to get the code from the
computer.

Q
Was this helpful?
Yes
No
1 person thought this was helpful

Solution #4

posted on May 14, 2008
Somewhat Helpful)

lawyer

Rank: Apprentice 
Rating: 0%, 0 votes
Was this helpful?
Yes
No

Solution #5

posted on May 14, 2008
Somewhat Helpful)

lawyer

Rank: Apprentice 
Rating: 0%, 0 votes
Most auto parts stores will check OBD2 codes free of charge. Obviously you
should then by the repair parts from them.

...
Was this helpful?
Yes
No

Solution #6

posted on May 14, 2008
Somewhat Helpful)

lawyer

Rank: Apprentice 
Rating: 0%, 0 votes
Bubba, 92 isn't OBD2.
Not that an auto parts store can't read them if they're not. :>)
Was this helpful?
Yes
No

Solution #7

posted on May 14, 2008
Somewhat Helpful)

lawyer

Rank: Apprentice 
Rating: 0%, 0 votes
Check the tension on the throttle springs. May need to be adjusted. Also,
rule out all the small things (air filter, vacuum, etc...)
...
Was this helpful?
Yes
No

Solution #8

posted on Mar 06, 2009
Very Helpful)

Toyota Guy

Rank: Wiz  Toyota Expert
Rating: 98%, 85 votes
You must jump TE1 and E1 in order to read codes




Was this helpful?
Yes
No
5 people thought this was helpful

Popular Solutions for 1992 Toyota Pickup


Questions and Unsolved Problems for 1992 Toyota Pickup


Do you recommend Toyota 1992 Pickup?
Answer

Answer
I have a 1992 two wheel drive, four cylinder toyota pickup truck and I'm replacing the alternator.... (More)

Answer
92 toyota pickup 4 cyl 4x4; starts and runs for 1 or 2 minutes then shuts off. will restart after... (More)

Answer
truck would run for about 7 to 10 seconds. I replaced the air flow meter,the thermo sensor and the... (More)

Answer
i need to set the lifters on a 1992 toyota pickup

Answer
diagram of fuellines and vaccum hoses


Didn't find what you were looking for?

Describe your Cars problem:




Ask our Experts

 

Solve Your Problem Now!
Chat Live with an Expert
Chat Now
Featured Parts
Parts for your 1992 Toyota Pickup
Powered by

Top Car Experts



Top Car Mechanics
in , TX
(713) 838-2886
Toyota

(800) 262-0795
Find awesome deals on a superior quality Discount...
Car Stuff


       
Solve Your Problem Now!
Chat Live with an Expert
Chat Now

Insert Link
Insert Image
Insert You-Tube clip
Insert List
Insert List
Spell Check

What is this?



Select