Question about 1998 GMC Sierra

1 Answer

Replace ign lock cly key won't turn on 1998 GMC PICKUP

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,319 Answers

Need to take apart and find what is not connected correctly as like the sector gear most likely behind the cylinder

Posted on Sep 11, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1998 GMC Sierra 5.0L won t shift out park when pressing brake.


Could be the brake switch or the shift lock solenoid. You may be able to turn the key switch to the unlock position and shift out of park before you turn the key switch on.

Jun 25, 2013 | GMC Sierra Cars & Trucks

1 Answer

2008 GMC Sierra pickup. Driving and all of a sudden it shut off then turned back on; the doors unlocked then locked again. Now it won't do anything. Checked the oil and it was empty - no oil at


Running with no oil is death for the motor ( Seized). When the alternator stopped working because the engine stopped the door lock control opened the door locks as it said you were below the required speed to have them locked

Mar 31, 2013 | 2008 GMC Sierra 1500

1 Answer

Part on my key snapped off in the ignition. What is the best way to get it out? Or do I need to replace the whole ignition?


Hi,
It's not all bad.
remove cowling and re-insert partial key.
Turn to the ACC/ intermediate key position .

The IGN barrell will be held in place by a location "***" on the IGN barrell in the lock assy.
Press this "***" while the key is in assy position and the Key/barrell should be able to be removed. The IGN barrell needs to be in the on/acc position in order to be removed for obvious reasons. Good Luck

Dec 15, 2010 | GMC Jimmy Cars & Trucks

1 Answer

After replacing battirs anti theft system wanted let car start it just turn over


Most likely ign lock assy has broken wires in the steering column. It wont read resist on key. The wires are very small and tend to break from the ign lock being turn off and on.

Nov 21, 2010 | 1998 Cadillac DeVille

1 Answer

HOW TO REMOVE KEY CLY


Remove the horn ,then the nut holding the steering wheel on,then using a steering wheel puller,remove the steering wheel,then remove the lock plate,using a lock plate remover,then remove the turn signal switch,and there is a screw pin,that holds the ignition key cylinder in,remove it,and pull the key cylinder out.

Jan 29, 2010 | 1988 GMC Safari

1 Answer

I changed the turn signal switch on my 2000 gmc pickup. There is now a security light on and the truck will not start. What do I need to do to reset security.


turn on ign-if light is flashing leave key on for 30 mins till theft light stays on ,then try to start-chech at ign switch to see if small 3 wire connector has been unplugged

Sep 19, 2009 | 2000 Chevrolet Silverado

4 Answers

97 gmc sierra no fuel no spark replaced ign module and pickup coil still no spark


1996 GMC 1500 Pickup.
Replaced Coil, Dist cap/Rotor, Ign Mod & pick-up.
All showed to be bad with OHM meter.

20A ECM-B fuse keeps blowing out and I'm afraid to burn these new parts up....

ANY IDEAS OUT THERE???

Mar 31, 2009 | GMC Sierra 1500 Cars & Trucks

1 Answer

Ignition switch installstion 1991 gmc jimmy


remove steer wheel with puller. u will see black cover remove 3 tork screws.remove. next u will need a special tool push dowd on plate . remove clip in center. lift turn arm . remove bolt for lock cly. turn key lock will slide out

Dec 11, 2008 | 1991 GMC S-15 Jimmy

Not finding what you are looking for?
1998 GMC Sierra Logo

Related Topics:

57 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...