Question about 2004 Kia Sorento

Open Question

On a 2004 Sorento, are the rear brake 'backing plates' mounted 'outside' of any rear axle seals or gaskets? They need replacement due to corrosion and pieces rusted off. Will be replacing rotors & pads shortly and want to replace the plates at the same time. Need to know if the 'ends' of the axles will need to come off also in order to remove the plates.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

warlock61
  • 659 Answers

SOURCE: rear axle seal replacement 1994 ford bronco

It is fairly easy to do. remove rear wheels and brake drums, remove the differential cover, rotate the diff to access the diff pin bolt and remove, remove pin, push axles inward and remove c clips, slide out axles and replace seals. reverse procedure

Posted on Dec 29, 2008

  • 6 Answers

SOURCE: Rear brake rotor removal

Should just pop right off. Hit it gently with rubber mallet, it might have rusted to the hub

Posted on Dec 19, 2008

aref_bilal
  • 13 Answers

SOURCE: I am changing the spark plugs on my 2004 Kia sorento

Be careful there.. If you remove the Throttle Position Sensor TPS or the throttle Cable, the engine light will come on because there is a certain setting that needs to be done to ensure accurate emission control.

Posted on Apr 14, 2009

  • 52 Answers

SOURCE: Rear Axle Seal Replacement

remove rear tires, then remove brake calipers and rotors, then remove the 4 nuts (each side) that hold the axle shafts to the axle tube (located around the axle tube behind the backing plate) then using a slide hammer pull the axle shafts out, next using a die grinder and an air hammer get he retainer collar and the bearing off (without damaging the axle shaft) then remove the seal and the outer race which will still be in the housing. next put it all back together, make sure the plate with the studs is still on then slide the seal, bearing, then retainer on (all new parts) and using a press push them all the way back on. then is simple reassembly.

Posted on Apr 22, 2009

BCally1
  • 133 Answers

SOURCE: Axle Seals

book time is a little over 6 hours to do both. if its your first time count on it taking a lot longer

Posted on May 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace grease seal on rear axle


Leaking oil at the rear wheels can be one of two things, Easy fix is brake fluid, this would be the rear brake wheel cylinder leaking. Check your brake fluid tank under the hood for low fluid. If that is ok. Your leak may be your rear axle shaft seal. You need to remove the tire/wheel ether way. Jack up the car to pull the wheel, take your lugs loose while the tire is still on the ground, it is easy to take them loose this way. Take the EM: brake off, and jack up this side of the car. Your car could have disk or drums as both are offered on some Dodges. Once the tire is off you will see if you have disk or drums brakes. If drums you will need to pull the drum off at access the brake cylinder to see if that is leaking or not. If drums you have to back off the brake shoes by the adjusting wheel thru a small access window in the back plate. If you have disk brakes the caliper is right there and will be easy to see if it is leaking. If you have determined it is the rear axle seal leaking, this may be best done by a shop, due to needing a few special tools to remove the axle and then reinstall a seal. You will need a slide hammer. If drum brakes you will have to remove the brake backing plate, this means shoes and all hardware, please take pictures and get as good focus as you can to see how everything goes back together. Once down to the axle mounting, remove the 4 bolts and attach the slide hammer and pop out the axle, catch any fluid that will leak out, once out you can determine which type of seal set up you have as some have press fit collars that may have to be cut off. . Hope this helps FixYa up.

Sep 12, 2011 | Dodge Ram 2500 Cars & Trucks

2 Answers

I HAVE A 03 TOWNCAR WITH LEAKING OIL AT THE RIGHT REAR WHEEL. I NEED HELP ON HOW AND WHAT TO CHANGE. ALSO SHOULD I DO BOTH SIDES. THANK YOU JERRY SORRELL 337-842-0485


Leaking oil at the rear wheels can be one of two things, Easy fix is brake fluid, this would be the rear brake wheel cylinder leaking. Check your brake fluid tank under the hood for low fluid. If that is ok. Your leak may be your rear axle shaft seal. You need to remove the tire/wheel ether way. Jack up the car to pull the wheel, take your lugs loose while the tire is still on the ground, it is easy to take them loose this way. Take the EM: brake off, and jack up this side of the car. Your car could have disk or drums as both are offered on the 2003 Town car. Once the tire is off you will see if you have disk or drums brakes. If drums you will need to pull the drum off at access the brake cylinder to see if that is leaking or not. If drums you have to back off the brake shoes by the adjusting wheel thru a small access window in the back plate. If you have disk brakes the caliper is right there and will be easy to see if it is leaking. If you have determined it is the rear axle seal leaking, this may be best done by a shop, due to needing a few special tools to remove the axle and then reinstall a seal. You will need a slide hammer. If drum brakes you will have to remove the brake backing plate, this means shoes and all hardware, please take pictures and get as good focus as you can to see how everything goes back together. Once down to the axle mounting, remove the 4 bolts and attach the slide hammer and pop out the axle, catch any fluid that will leak out. Hope this helps FixYa up.

Aug 13, 2011 | Lincoln Town Car Cars & Trucks

1 Answer

When do you change the fluid in the rear differencial. I was told by a mechanic that the rear differencial fluid was low and had metal shavings in it, and that the fluid needed to be changed and that it...


I'd say yes. The differential fluid is often overlooked by oil change technicians, even though it's something that should be topped off periodically.

It probably would cost more than that to repair it once it wears out.
Axle Housing Assembly Removal & Installation To Remove:
  1. Lift the vehicle.
  2. Drain the lubricant from the rear axle housing.
  3. Remove the rear axle assembly from the vehicle.
  4. Remove the brake caliper brackets from the rear hubs.
  5. Remove the rear cover and gasket from the rear axle housing.
  6. Remove the rear axle shafts from the vehicle.
  7. Remove the rear differential assembly from the vehicle.
  8. Remove the brake backing plates from the rear hubs.
  9. Remove the rear drive pinion shaft yoke and seal from the drive pinion.
  10. Remove the drive pinion from the rear axle housing.
To Install:
  1. Install the drive pinion into the rear axle housing.
  2. Install the rear drive pinion shaft yoke and seal onto the drive pinion.
  3. Install the rear differential assembly into the vehicle.
  4. Adjust the differential side bearing preload and the backlash.
  5. Perform a gear tooth contact pattern check.
  6. Install the brake backing plates onto the rear hubs.
  7. Install the rear axle shafts into the vehicle.
  8. Install the rear cover and gasket onto the rear axle housing.
  9. Install the brake caliper brackets onto the rear hubs.
  10. Install the rear axle assembly into the vehicle.
  11. Refill the lubricant in the rear axle housing.
  12. Lower the vehicle.
prev.gif next.gif ---
I think that changing the fluid would take about an hour, and depending on the garage, and the labor rate, that they might elect to take the rear cover off of the differential, and drain it that way and replace the fluid once it was put back on. He could inspect the gears while the cover was off and tell you how bad it was.'

Do you hear any clunking or gear mesh noises from the rear when putting it in gear or running the vehicle?


Some mechanics would simply top off the fluid and wait until it wears out, which could be several thousand miles in the future.

Use gear oil for it of the recommended viscosity in the service manual.

Generally thicker than motor oil.

So, adding fluid would cost only the amount of the fluid plus some labor.
A bottle of fluid might cost $9.99 or so depending on where you get it.

You might be able to do this yourself if you crawl under there, remove the fill plug at the top, and just add gear oil. If there isn't enough room you might drive it up on some ramps and then crawl under there.

Jul 29, 2010 | 2004 GMC Envoy

1 Answer

Rear axle removal on a 2004 f150 fx4


First thing is to make sure you chock the front tires so the truck will not roll. Raise the rear end and set it on jack stands. Put the transmission in Neutral and make sure the parking brake is off. Remove the rear tires and disassemble the brakes on the side with the leaking seal. Place a drain pan under the rear differential and remove the cover. Remove the differential shaft lock bolt. You will need to turn the drive shaft by hand to access the bolt. It will be on the right side off the spider gear housing. Only use a 5/16 or 8mm 6 point box end wrench to remove the bolt. After you remove the bolt reach on the top of the spider gear housing and push the differential lock shaft down to remove it. Make sure the spider gears do not rotate after you remove the shaft. If they do you will need to realign everything to reinstall the lock shaft. Push the axle shaft in enough to remove the "C" clip from the tip of it. The axle will now slide out of the rear end. You can use the tip of the axle shaft to remove the axle seal. If you're changing the bearing as well you will need a slide hammer with axle bearing adapters to remove it. You can use a socket and hammer to install the new bearing and seal. Be careful not to damage the bearing and seal. I recommend packing grease in the back side of the seal. This helps prevent the spring on the seal lip from coming off. Assembly is the reverse. Clean off all the gear oil from the differential cover and the axle. You can use RTV as a gasket if the OEM gasket is damaged. Fill the rear end with new gear oil of the proper type. Refer to your owner's manual.

Jun 05, 2010 | 2004 Ford F150

2 Answers

How do you remove the rear axle to change the axle seal, from a 2004 Coloraro?


remove the center cover facing the rear of the truck. you will see side gears with the shafts axle end at each side gear. a C clip will have to be removed from each shaft at the end of each axle. Then remove the wheels and pull out the axles

Feb 06, 2010 | 2004 Chevrolet Colorado

1 Answer

I have a leak from my rear axle seal. How do you


JACK up the truck and block other rear wheel both back and take hand brake off ,,remove rear wheel/brake drum/handbrake cable from rear brake/remove metal brake hose/remove rearbacking plate with all parts fitted to it ie brakeshous 4or5 bolts holding the rear axle in to housing and when all parts off then put on a IMPACK PULLER and remove complete backing plate with axle assy and take to the engineering shop to get it pressed off and a new bearing and seal assy pressed back on .
Then refit in reverse of removal and bleed the brakes and top up the rear axle of oil (EP90) apply h/brake take out blocks and lower jack and test drive .. BUT MAKE SURE THE BRAKES ARE 100%

Oct 14, 2009 | 2005 Ford F 350 Super Duty

1 Answer

I have a 94 jeep wrangler front left axle seal bad. I took the left side apart and not sure how to get the seal back in. Do I need to open the inspection cover on the diff. and take the gears out?



Rear Axle Notes
  1. Raise and support vehicle.
  2. Remove rear wheels.
  3. Scribe alignment marks on propeller shaft and axle for proper assembly, then disconnect propeller shaft from axle.
  4. Disconnect the track bar from axle mounting bracket.
  5. Disconnect parking brake cable at equalizer.
  6. Disconnect shock absorbers at axle tubes.
  7. Disconnect hydraulic brake hose at rear axle Tee-fitting, then tape ends of hose and fitting to prevent contamination.
  8. Disconnect axle vent tube from axle.
  9. Remove U-bolts and tie plates.
  10. Loosen spring mounting bolts.
  11. If equipped, disconnect ABS wiring connections at axle.
  12. Support axle with suitable jack.
  13. Remove spring-to-shackle attaching bolts and lower spring to the floor.
  14. Remove axle assembly.
  15. Reverse procedure to install.

Front Axle Notes
  1. Raise and support vehicle at frame behind front springs.
  2. Remove front wheels.
  3. Scribe alignment marks on propeller shaft and axle yoke for proper assembly, then disconnect propeller shaft at axle yoke.
  4. Disconnect connecting rod at steering knuckles.
  5. Disconnect shock absorbers at axle housing.
  6. Remove stabilizer bar connecting links to spring tie plates attaching bolts, if equipped.
  7. Disconnect breather tube at axle housing.
  8. Disconnect stabilizer bar link bolts at spring clips.
  9. Remove disc brake calipers, rotors and brake shields.
  10. Remove U-bolts and tie plates.
  11. Support axle assembly with suitable jack to relieve spring tension.
  12. Loosen rear spring shackle to spring attaching bolts.
  13. Remove front spring shackle to spring attaching bolts and lower spring to floor.
  14. Remove axle from under vehicle.
  15. Reverse procedure to install.

Jul 21, 2009 | 1994 Jeep Wrangler

1 Answer

How do you remove right rear axle on a 2004 ford crown vic to replace seal on wheel?


Section 05-02A: Axle, Integral Carrier — 8.8-Inch Ring Gear 1994 Town Car, Crown Victoria/Grand Marquis. Workshop Manual REMOVAL AND INSTALLATION Axle Shaft NOTE: Whenever replacing the rear axle lubricant, use Rear Axle Lubricant XY-90-QL (ESP-M2C154-A) or equivalent.
Removal
sra~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: The rear brake anti-lock sensor must be removed before the axle shafts are removed. The rear brake anti-lock sensor is bolted on the rear disc brake caliper anchor plate.
  1. Raise vehicle to desired working height. Refer to Section 00-02 . Remove rear wheel (1007) and tire assembly. Remove rear disc brake calipers (2552) and rear disc brake rotors (2C026) .




  1. Clean all dirt from area of axle housing cover with a wire brush and/or cloth.
  1. Drain rear axle lubricant by removing the axle housing cover .
  1. Remove differential pinion shaft lock pin and differential pinion shaft .


    9979cb3.gif
  1. Push flanged end of the axle shafts toward the center of the vehicle and remove the rear axle shaft retaining u-washer from the button end of the axle shaft .



  1. Remove axle shaft from the rear axle housing , being careful not to damage the inner wheel bearing oil seal (1177) and rear brake anti-lock sensor ring.
Installation
NOTE: Check for presence of rear axle shaft o-ring (4A332) on the spline end of the shaft and install if not present.
sra~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Care must be taken not to let axle shaft splines damage oil seal or bearing assembly.
  1. Carefully slide axle shaft into rear axle housing without damaging rear wheel bearing (1225) or rear brake anti-lock sensor indicator (2C189) . Start splines into side gear and push firmly until the button end of axle shaft can be seen in the differential case .
  1. Install the rear axle shaft retaining u-washer on the button end of the axle shaft splines, then pull the shaft outboard until the shaft splines engage and the rear axle shaft retaining u-washer seats in the counterbore of the differential side gear .
  1. Position the differential pinion shaft through the differential case and differential pinion gears , aligning the hole in the differential pinion shaft with the lock bolt hole. Apply Rear Axle Lubricant to differential pinion shaft lock pin . Install differential pinion shaft lock pin and tighten to 20-41 Nm (15-30 lb-ft). sra~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Differential pinion shaft lock pin must be tightened to specification using Stud and Bearing Mount E0AZ-19554-BA (WSK-M2G349-A1) or equivalent.




    NOTE: Axle housing cover must be installed within 15 minutes of application of the silicone rubber or new silicone rubber must be applied.
    sra~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Make sure machined surfaces on both axle housing cover and rear axle housing are clean before installing the new silicone sealant. Inside of axle must be covered when cleaning the machined surface to prevent axle contamination. Tighten the cover bolts in a crosswise pattern to ensure uniform draw on axle housing cover .
  1. Apply Silicone Rubber D6AZ-19562-AA or BA (ESB-M4G92-A or ESE-M4G195-A) or equivalent. Install axle housing cover and tighten retaining bolts to 28-38 Nm (38-52 lb-ft).



  1. Add Motorcraft Rear Axle Lubricant XY-90-QL or KL (ESP-M2C154-A) or equivalent until it is 6-14mm (1/4-9/16 inch) below bottom of fill hole. Add 118.3 mL (4 oz) of Ford Additive Friction Modifier C8AZ-19B546-A (EST-M2C118-A) or equivalent to Traction-Lok axles. Install fill plug and tighten to 20-41 Nm (15-30 lb-ft).
  1. Install rear brake anti-lock sensor indicator . Tighten retaining bolt to 4.5-6.8 Nm (40-60 lb-in).
  1. Install rear disc brake caliper and rear disc brake rotor .
  1. Install wheels and tires.
---------------------------------------------------------
  1. Insert Rear Bearing Remover T85L-1225-AH in bore and position it behind bearing so tangs on tool engage bearing outer race. Remove rear wheel bearing and inner wheel bearing oil seal as a unit, using Impact Slide Hammer T50T-100-A.

    Rear Disc Brake Caliper Anchor Plate




  1. Lubricate the rear wheel bearing with Rear Axle Lubricant.



  1. Install rear wheel bearing into the housing bore using Axle Tube Bearing Replacer T78P-1225-A.



    sra~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Installation of rear wheel bearing or inner wheel bearing oil seal assembly without proper tool may result in an early bearing or seal failure. If inner wheel bearing oil seal becomes cocked in bore during installation, remove it and install a new one.
  1. Install the inner wheel bearing oil seal using Axle Tube Seal Replacer T78P-1177-A. Use Premium Long-Life Grease XG-1-C or K (ESA-M1C75-B) or equivalent between the lips of the inner wheel bearing oil seal .



  1. Install axle shafts as outlined.

May 13, 2009 | 2004 Ford Crown Victoria

1 Answer

Rear Axle Seal Replacement


remove rear tires, then remove brake calipers and rotors, then remove the 4 nuts (each side) that hold the axle shafts to the axle tube (located around the axle tube behind the backing plate) then using a slide hammer pull the axle shafts out, next using a die grinder and an air hammer get he retainer collar and the bearing off (without damaging the axle shaft) then remove the seal and the outer race which will still be in the housing. next put it all back together, make sure the plate with the studs is still on then slide the seal, bearing, then retainer on (all new parts) and using a press push them all the way back on. then is simple reassembly.

Apr 21, 2009 | 2004 Jeep Grand Cherokee

1 Answer

Rear end seal leak


You must be refering to the side seals. common problem. the actual problem with those rear ends is the air breather, which cloggs up and that's when your seals blow out, because the pressure in the rear end has nowhere to go and so your seals get blown out. I just did a set on Monday. Anywho, you will need some specialty tools for this. You will need to remove both rear brake assemblys (rotors, calipers). Than look on the other side of the backing plate, there you will see 4 big nuts that hold the backing plate on the axle tube (rear end). Remove those 4 nuts and that's where specialty tools become usefull. You will need a slide hammer. You need to attach the slide hammer onto the axle right by the studs. Use factory whel nuts to attach. Remove axle out of the housing with few good slides of the slide hammer. Once the axle is out, you need to remove the snapp ring, then cut the colar off and remove colar, then remove the old bearing and thats where the seal is. Big help doing this job is a pneumatic air hammer, which helps you remove the stuff off the axle shaft and the slide hammer to remove the axles out. You will need 2 seals, 2 bearings and 2 collars. You may also need the plates with the studs, which had the big nuts, that you removed in first steps of this repair. Kind of a job for someone that has been working on cars and has the tools to do it. Good luck. Oh ya, change the breather and the fluid in the rear end.

Oct 21, 2008 | 2004 Nissan Titan

Not finding what you are looking for?
2004 Kia Sorento Logo

Related Topics:

421 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

yadayada
yadayada

Level 3 Expert

75744 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...