Question about 1991 Oldsmobile Cutlass Supreme

Open Question

Location of o2 sensor on my 93 cutlass olds. 3.1 liter v6

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

justuscc
  • 360 Answers

SOURCE: Map Sensor Location

back of the intake please leave feed back thanks

Posted on Sep 18, 2008

muttandjeff
  • 359 Answers

SOURCE: 93 olds cutlass . oil pressure gauge when started car todaygauge did not moveoil level fineruns perfectguage just at low end of guage

2 things come to mind check the negative terminal of battery and the ground wire connected to engine location varies where they connect these but will always originate from neg on battery a quick check to see if you have a proper ground connection is to take one booster cable and connect to neg post on battery and connect the other end to the engine on clean metal (be sure to keep clear of moving parts ) start engine and see if you have pressure on gage if so you must clean ground connection to engine .if this does not correct possible bad sending unit in side of block with one wire connected to it . caution ** temperature sending unit look similar so make sure with one you are taking out

Posted on Dec 23, 2008

  • 1 Answer

SOURCE: where is the cam sensor

where is the ignition moduale located on a 1993 olds ciara 3300motor not geting spark to the coils

Posted on Jan 12, 2009

STEVIE_N_24
  • 147 Answers

SOURCE: o2 sensors on a 99 mercury cougar v6

Should be 4. One in front of the catalytic converter and one after on both front and rear exhaust.

Posted on Mar 30, 2009

  • 55 Answers

SOURCE: location of bank 1 sensor 1 o2 sensor

Should be in the manifold on the back side closest to the firewall.

Posted on May 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

LOCATION OF B1S1 SENSOR FOR 2002 AUDI A6 QUATTRO


Referencing oxygen sensor or O2 sensor or 'lambda sensor':

B1S1 is 'bank 1', which is the passenger side cylinder bank on a V6 or V8.

S1 is the 'upper' or 'upstream' sensor, closest to the cylinder.

Jan 28, 2017 | 2000 Audi A6

1 Answer

88 olds cutlass 2.8 liter code 43 engine runs poorly


Code 43 means rich I think, so could be Coolant temp sensor, O2 sensor, leaky injector(s), tune-up items, other.

Aug 14, 2016 | Cars & Trucks

1 Answer

Removing thermostat housing


my son is electrical engineer,he can answer

Feb 27, 2014 | Oldsmobile Cars & Trucks

1 Answer

I have 1995 olds cutlass cierra s with 3300 v6, dies when warm, rest for about 15 min and starts up till warm. replaced ignition module, o2 sensor, fuel filter, fuel pump, air filter. i've worn out my...


the most common problem next is the crank sensor. use a heat light to warm up the sensor to see if it is that. by using a heat light you can narrow down what part has the temperature glitch. Don't forget to try the engine computer.

Jun 06, 2011 | 1995 Oldsmobile Cutlass Ciera

1 Answer

CRANK SENSOR LOCATION FOR 1992 OLDS CUTLASS CIERA


That year Ciera came with two diiferent engines. if you have the 2.5 liter engine it is located under the hood, center, rear engine area, below ingnition coil pack and DIS module, mounted in engine block. If it is the 3.3 liter engine it is located under the hood, passenger side, lower engine area, front of crankshaft pulley, mounted in engine block. i hope this helps you and good luck.


Mar 15, 2011 | 1992 Oldsmobile Cutlass Ciera

1 Answer

I am wanting to know where the front oxygen sensor is located in my 99 oldsmobile cutlass 3.1 v6! Thanks!


First off you need to know what you are looking for. I will post a photo of the sensor removed from the exhaust. Start at the engine exhaust manifold and go backward to the rear of the car. You will find the O2 sensor. More than likely it will be located very close to the engine on pipe that joins the two pipes coming from the manifold together into one. It will be screwed into this pipe. b2dbcc8.png

Oct 05, 2010 | 1997 Oldsmobile Cutlass Supreme

1 Answer

93 OLDS HALF SHAFT REMOVAL LEFT SIDE


the procedure to remove them is here As for the seal you should be able to pry the old one out once you have removed the half shaft with a screwdriver or ask at your local parts store if they can rent/sell you a seal removal tool
hope this helps!

Feb 19, 2009 | 1993 Oldsmobile Cutlass Supreme

2 Answers

Where is the cam sensor located on a 1994 olds cutlass cerias


with a 3.1 liter , remove and install directions are remove serpentine belt , remove power steering pump assembly , then remove sensor harness , sensor bolt , remove sensor , so it sounds like behind the power steering pump assembly area if that makes sense . it has to be real close the the cam gear , you should be able to find it .

Dec 29, 2008 | 1993 Oldsmobile Cutlass Ciera

Not finding what you are looking for?
1991 Oldsmobile Cutlass Supreme Logo

Related Topics:

199 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...