Question about 2005 Nissan Altima

1 Answer

Changed the starter in my nissan and now the engine light came on. Dose the maf sensor need to be replaced with the starter?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 32 Answers

What would draw you to the Mass air flow sensor? Is there a code for it? If there is no code then most likely one of the wires on the starter may not be completely tight. Occasionally this will cause the check engine light may come on.

Posted on Sep 11, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000kia sportage dash lights comes on clicks but wont turn over changed battery woukd maf sensor keep from tuening tried jumping off still same


Scan vehicle for codes a maf sensor will through a code. I am thinking your starter is bad. The clicking noise is from the starter trying to activate the engine.

Apr 26, 2016 | Cars & Trucks

1 Answer

Runs good sometimes than check engine lights goes on runs bad I replaced the maf sensor than it still dose the same thing


Replaced the MAF Sensor--Why--on a wish & hope strategy,
with no testing or parts failure?

Are you not getting codes & looking up the possible causes,
the codes were set,then component testing?

Codes do not indicate that a part failed,just that the sensor
is out of range,you have to find out why

May 05, 2014 | Cars & Trucks

1 Answer

Maf sensor


was it a new maf fitted or a referbed unit
most new mafs sold only have a 6 month warranty

are there any other fault codes present or just the maf fault code

I agree with you a fault in the maf can make the car behave that way
the maf has a few functions with sensors in the unit

other sensors can also cause the engine to behave that way
02 sensor / faulty transmission solenoids and TPS



different car maker
i have just done a diode jump at the ECU
bypassing a faulty sensor in a maf
so far maf throws a fault code but no more problems

mmm-5nrggpflz035lvswkxm5zg5a-4-0.jpg

index-5nrggpflz035lvswkxm5zg5a-4-1.jpg

Mar 01, 2017 | 1994 Nissan Altima

2 Answers

2000 nissan maxima no start


Check your ignition fuses one may be shot

Jun 04, 2012 | 2008 Nissan Maxima SE

1 Answer

Why does my car throw the code P0100 and P0325? I have a 1995 Nissan 240sx. and it has a random misfire once in a while.


Hi,

Often a single issue can trigger multiple diagnostics codes, especially if the circuits are closely related.

Code P0100 = Mass Air Flow (MAF) Circuit malfunction

The computer has detected an issue with the MAF sensor.

- Verify the MAF sensor wiring is connected and wiring is in good condition
- Unplug and reconnect the MAF harness
- Check that voltage to the MAF sensor is within factory spec


Code P0325 = Knock Sensor # 1 Circuit malfunction

A knock sensor tells the engine computer when one or more of your engine's cylinders are "knocking", that is, exploding the air/fuel mixture in a way that delivers less power and can be damaging to the engine if prolonged. The computer uses this information to tune the engine so that it doesn't knock. If your knock sensor wasn't operating properly, so that it was always indicating a knock, the engine computer's response may have been to change the ignition timing on your engine. Knock sensors generally bolt into or thread into the engine block.

- Check condition of the knock sensor wiring.
- Test the 'Ohms' reading of your Knock Sensor (undo the connector and measure the pins) to ensure it is within spec (ask Nissan for this measurement). If out of spec, replace the knock sensor.

Cheers,


"If this solution resolves your issue, please be kind enough to leave a testimonial"


Jun 08, 2011 | Nissan 240SX Cars & Trucks

2 Answers

I checked the "service engine


Check the 02 sensor for starters. The code indicates a slow response from the sensor, which is usually the sensor but sometimes bad upstream exhaust leaks.

Feb 18, 2011 | Nissan Altima Cars & Trucks

1 Answer

Maf sensor malfuction?


The MAF is the most important sensor in your engine, as it tells the computer what it needs to be able to set the mixture on the fly properly at any throttle position. A MAF depends on several other sensors to function. Get your engine codes run and replace any part that is marginal or bad. Good luck.

Nov 28, 2009 | 1991 Nissan Pickup

2 Answers

Fault Code reads MAF Sonsor even after replacing the part


It is very possible that you have an open circuit in your connector. I do agree that aftermarket parts have different resistance valves than the OEM, but in this case I think you have more of an electrical problem than a parts replacement problem. Check continuity from the MAF connector to the ECM. Make sure you clean out the air cleaner box and install a new OEM air filter. Aftermarket filters don't alway fix properly and can leave an air gap around the filter. This can allow debris to enter the engine and also contaminate your MAF.

Jul 21, 2009 | 2004 Nissan Sentra

1 Answer

Car will not move


did you replace the MAF mass airflow sensor ? If you did not, clean it with electronics cleaner so it won't damage the sensor. that could be the cause. also the EGR vavle would cause a problem like that.

Aug 05, 2008 | 2003 Nissan Sentra

Not finding what you are looking for?
2005 Nissan Altima Logo

Related Topics:

110 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...