Question about 1995 Buick LeSabre

1 Answer

My 1995 Buick lasabre license plate light screws are just spinning and i cant get the light out to replace it and i don't want to break it what do i do

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 228 Answers

Are they a 1/4 in looking sheet metal screw? try some rust buster on the back side if you can spray some on the thraeds, or grind the heads off wih a dremmil tool. or remove the outer panel.

Posted on Sep 11, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Change the license plate lights in my 2002 buick rendezvous cx


On most GM cars, SUV's, and light duty trucks, the license plate light bulbs are held in place by 2 screws...located on each side of the plastic lens...remove these 2 screws then wiggle the entire assembly out so you can view and replace the bulbs...Again most GM cars have 2 bulbs also...Hope this helps.

Sep 06, 2013 | 2002 Buick Rendezvous

1 Answer

Replace license plate blub in 2002 buick lasabre


your going to remove the entire trunk lid assembly from the vehicle. If you open the trunk and look from the inside you should either see black plastic wing nuts or 10mm nuts holding the assembly to the trunk. There will be approximately 10 of them that will need to be removed. Once they are removed the lens assembly will pop away from the trunk lid. The license bulbs can then be replaced. I usually replace all six taillight/license bulbs whenever I have one of these apart. Its the same bulb for all six lights.

Oct 02, 2011 | Cars & Trucks

1 Answer

Looking for a license plate holder for a 95 Buick Lasabre


eBay, craigslist, junkyards, auto recyclers. go to google and start searching.

Sep 06, 2011 | 1995 Buick LeSabre

2 Answers

How do I change the high rear break light on 1993 Buick Lasabre


Hello,
You need to -
  1. Open the trunk and look where the speakers are located.
  2. There is a plate in the middle held in place with two screws.
  3. Remover the screws
  4. Remove the plate and you will now have access to the bulb.
  5. Twist the bulb connector to the left and pull the bulb assembly out.
  6. Now the bulb pulls strait out.
  7. Install new bulb.
  8. Reverse steps to finish job.
Regards, Tony

Feb 26, 2011 | 1993 Buick LeSabre

1 Answer

How do I replace license light bulbs in my 1995


I have a 2002 which is a little different body style but it may be the same process. You have to take the back plastic section that holds the license plate loose from the car. There are bolts that are inside the trunk that hold the plastic panel on. Mine are in the trunk lid. If your plastic panel, license plate, etc. goes up with the trunk lid they are in the lid. You need deep type sockets to reach the nuts, at least mine does.

Mar 31, 2010 | 1995 Buick LeSabre

1 Answer

License plate light out 99 buick lasabre


same circuit with your parking light

Feb 27, 2010 | 1999 Buick LeSabre

1 Answer

I can't get to the license plate bulb in a buick lesabre.....don't want to force the plastic....


There should only ne two little screws on the plastic plate for the bulb. just unscrew and gently pull downward till bulb and harness are exposed. this should be a 194 bulb just pull out and replace with a new one.

Apr 05, 2009 | 1995 Buick LeSabre

2 Answers

Lhow do i replace icense plate light bulb


Sometimes you got to be mean to it. The method for removal is to push in and then turn.

Jan 20, 2009 | 1995 Buick LeSabre

1 Answer

How to change the rear lights on a 2003 Buick Century, rear lights being the break, parking and license plate lights.


yes you will you will have to take side trims and sill panel off get a 10 mm ready and take the bolts out the tail liaghts should come out the license lamps have screws in them and if you looka t them but you should be able to twist bulbs and pull them out / Please rate my response thank you very much

Jan 02, 2009 | 2003 Buick Century

1 Answer

1997 LaSabre license plate lights.


Most likely, the j-nuts have rusted in half, so the back half that has the thread contact is just spinning. If you can, look/hold from behind and have someone try to unscrew them.

Dec 10, 2008 | 1997 Buick LeSabre

Not finding what you are looking for?
1995 Buick LeSabre Logo

184 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...