Question about 1988 Daihatsu Charade

1 Answer

Have fitted new timing belt all timing makrks linre up but car will not fire

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

If its a 4 cyl. ford then your off a tooth even though it appears to be right.when its right it looks like its off a tooth

Posted on Sep 25, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Mitsubishi Pajero io 4G94GDI Engine ignition


no spark at the plugs can be
immobiliser not working
cam/crank position sensors not working
broken timing belt
faulty coil/s faulty distributor cap/rotor ( if fitted)

Oct 29, 2014 | Mitsubishi Pajero Cars & Trucks

1 Answer

I changed timing belt on 3.2 liter v6 1990 grand am. Why is it still sputtering and back firing


It sounds if the timing is out a tooth. if it run ok before the belt change that is the fault . remove the timing cover , check out timing marks by turning engine clock wise only. after fitting a new belt I all ways set tension and rotate engine twice and recheck marks , saves a lot of time if a tooth out.

Aug 10, 2014 | Cars & Trucks

1 Answer

I have a 2003 kia sedona van 3.5 liter that jumped time. I reset the timing put a new belt on it and it ran good for 35-45 min. Then it cut off, and wouldn't start back up. It has an OBD2 code for cam...


cam sensor fail can be crank sensor fail engine will run with cam sensor fail but crank it will not fire. also recheck the timing belt settings you fit the timing belt and run engine till warm then recheck the belt adjustment to make sure its in line and at recommended tightness.

Aug 07, 2017 | Cars & Trucks

1 Answer

I have a 91 626 mazda, timeing belt broke and the water pump was leaking...so i left it in the garage,the car was not worked on unitl ten months later,i changed the timeing belt and water pump,also new...


Check the ECM for codes. Cam or crank sensors will cause a no start. Also there should have been a compression and/or leak down test performed on the engine before the belt was replaced. This is done to make sure that the pistons didn't bend the valves. Bent valves will cause a nostart because of no compression. First check for codes then do a compression test before you replace anything. Let me know
Randy

May 07, 2011 | 1991 Mazda 626

1 Answer

Timeing belt broke have replaced now not fireing


You either have the belt 180 degrees off. So you have to take belt off and turn crank only (slowly) around once to its mark again, but first you need to go to a website that lists motors that are called "interference fit" engines. (Think Gates belt co. has a list) If your motor is an interference fit then when belt broke the motor is trashed. Interference fit means that pistons can hit valves if the belt breaks. That is why they tell you to replace the timing belt before too long. Also if motor is interference fit when you try and turn crank go slow because you may bump into valve.

Apr 04, 2011 | 1993 Geo Storm

1 Answer

Belt came off and wrapped around the crankshaft pully then would not start.....seems like timing had changed....won't fire....would it be a sensor behind the pully? and are they adjustable?


The sensors are not usually adjustable, it looks like the timing belt has jumped a tooth or two, fit new timing belt to orinigal marks on engine, hopefully there is no damage done to the engine you will know when you try to start the motor.

Aug 14, 2010 | 1989 Oldsmobile Eighty Eight Royale

2 Answers

Back Fires


Was it back firing before your son replaced the timing belt.

Oct 12, 2008 | 1989 Mitsubishi Galant

4 Answers

Timing belt trouble


I need the firing order for a 98 ford escort

Sep 14, 2008 | 1998 Ford Escort

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daihatsu Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76070 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4521 Answers

Are you a Daihatsu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...