Question about 1993 Mercury Topaz

1 Answer

I have a 1993 mercury topaz. my driver side shoulder belt is only going half way instead of all the way back.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 66 Answers

The recoil spring in your belt case is wearing out. the whole assembly will have to be changed out.

Posted on Sep 11, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1993 Topaz V6 engine coolant leak


sounds like a core plug or freeze plug in american ,but without a good look i honestly tell you

Nov 19, 2012 | Mercury Cars & Trucks

1 Answer

How do I disable the seat belt motor


Remove the trim around the inside of the door, the motor is right there in plain sight

May 24, 2012 | 1992 Mercury Topaz

1 Answer

I have a 1993 Mercury Topaz that I just bought, and the drivers side seat will not move forward, it will go in all other directions, but won't move forward...any suggestions?


There are 3 electric motors on the seat. One is forward and back, one is front up and down, and one is rear up and down. The switch changes the polarity back and forth to achieve the proper movement. I think the wire color for the forward and back motor is yellow with a white tracer and red with a white tracer. so if the switch gives the motor positive voltage to the yellow with a white tracer and grounds the red with a white tracer the seat moves forward. If the switch gives the red with a white tracer positive and the yellow with a white tracer ground the seat moves back. (or the other way around). So we can safely say it is in the switch.
Good luck and God Bless

Jun 06, 2011 | 1993 Mercury Topaz

1 Answer

Where is the check plug for the transmission on a mercury topaz standard transmission


Raise the car and check underneath. You should find a drain plug at the bottom of the tranny, and the fill plug is either on one side or towards the back. I can't find the diagram for your car, but this should be easy to find.
Some cars have a rubber check/fill plug. This is where you check the fluid level, on a flat surface. You also fill it up here, to the top of the check window. You have to use a fluid pump to fill it up. You can use a small hand pump that pumps it out of the container, or get fancy with a bigger model that holds the fluid also.
Some cars have a window cap that is a bolt with a half inch square in the middle. Just use a half-inch socket wrench with out a socket on it, or half-inch breaker bar.
Hope this helps.

Feb 11, 2010 | 1993 Mercury Topaz

1 Answer

1993 mercury villager- drivers side seatbelt is stuck.


You have a limit switch at each end of the seat belt track. One could be bad. Is belt stuck forward or at the back? It also has a module to control it.
It operates like a garage door opener. If you have to replace track, it's a big job. Have to take a lot of trim off the van. Best thing to do is get it in the rear position and just use the buckle. Get used part at car-part.com.
page with * is lowest pice. Or, go to pick n pull salvage yard and pull it yourself and learn how it comes out.

go here for team villager help

http://groups.yahoo.com/group/villagerquest/

Jul 29, 2009 | 1993 Mercury Villager

1 Answer

Mercury Topaz serpentine belt diagram


I have a 93 topaz, the diagram label is under
the hood itself.

Jul 16, 2009 | 1993 Mercury Topaz

1 Answer

Need diagram for 1993 mercury topaz fuse box


Get the Haynes manual - Ford Tempo & Mercury Topaz 1984 thru 1993.

That is what I had to do .

http://www.haynes.com/products/sfID1/3/sfID2/5/sfID3/38/productID/171

Apr 06, 2009 | 1993 Mercury Topaz

1 Answer

1993 mercury topaz GS Engine noise


Another guess would be the water pump going bad. That noise can be loud when it gets pretty bad and makes like a metal on metal grinding noise

Nov 06, 2008 | 1993 Mercury Topaz

Not finding what you are looking for?
1993 Mercury Topaz Logo

Related Topics:

96 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

fordexpert

Level 3 Expert

5546 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...