Question about 1994 Toyota Pickup

1 Answer

How do you replace sidemarker front end bulb i cant get past the 2 screws

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Governor:

    An expert whose answer got voted for 20 times.

  • Toyota Expert
  • 178 Answers

It's been a while since I replaced mine but as I recall once you remove the screws the housing can be pulled from the body. There are plastic pins and sockets that hold it in place.

Posted on Sep 21, 2010

  • JeB
    JeB Feb 04, 2011

    Ok ... had to do this to my truck again today. As above, remove the two screws holding the housing to the body. Then pull the housing away from the headlight housing ... there are two metal pins in the side marker housing that plug into plastic sockets in the headlight housing. If stuck you can use a flat blade screwdriver to carefully do some prying. The bulb is a 168 series. Some sort of lube on the pins/sockets may help with the separation if there's a next time. (I'm guessing I replaced this same bulb 5-6 years ago)

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Changing backup bulbs on 2005 buick rendevous


TAIL LAMP ASSEMBLY AND /OR BACKUP, SIDEMARKER, STOP, TURN SIGNAL BULB REPLACEMENT

REMOVAL PROCEDURE

1. Open the liftgate.
2. Remove the screws from the tail amp.
3. Slide the tail lamp rearward in order to disengage it from the retainers on the rear body panel.
4. Disconnect the electrical connector from the tail lamp wiring harness.
5. Remove the tail lamp and side marker lamp sockets from the tail lamp, depressing the locking tab and turning counterclockwise.
6. Remove the bulbs from the tail lamp and the side marker lamp sockets, if replacing the bulbs.

INSTALLATION PROCEDURE

1. Install the bulbs to the tail lamp and side marker lamp sockets, if removed.
2. Install the tail lamp and side marker lamp sockets to the tail lamp, turning clockwise until the locking tab is fully seated.
3. Connect the tail lamp electrical connector to the wiring harness.
4. Position the tail lamp retainer slots to the tabs on the rear body panel.
5. Install the tail lamp to the rear body panel, pressing into place until fully seated.
6. Install the tail lamp screws to the Taillamp.

NOTE: Refer to Fastener Notice in Service Precautions.

Tighten the tail lamp screws to 2 N.m (18 lb in).

7. Close the liftgate.

Apr 16, 2017 | Buick Cars & Trucks

1 Answer

Passenger side turn signal flashes faster but dont work even at day runing light, comes on when head lights are on, replace bulb and socket because was melted but stilldoes the same


Turn Signal Lamps
The turn signal lamps may only be activated with the ignition switch in RUN or BULB TEST position. The T/SIG fuse supplies ignition voltage to the turn signal switch. When the turn signal switch is placed in either the left or right position, the turn signal switch sends an ignition voltage to the hazard lamp/turn signal flasher, which sends an on-off signal to the turn signal switch. When the turn signal switch receives the on-off signal it will send that signal to the following lamps on the LH or RH side:
?€¢
The Rear Turn Lamp


?€¢
The Turn Signal Indicator


?€¢
The Sidemarker Lamp


?€¢
The Sideview Mirror (Pontiac Thunder only)

The turn signal switch also sends a separate on-off signal to the Daytime Running Lamps (DRL) control module, which relays the signal to the appropriate front turn signal. The front turn signals are grounded at G101 and G102. The rear turn signals are grounded at G401. The sidemarker lamps are grounded through the corresponding front parklamp.
The sideview mirror turn signals are a bank of LEDs placed behind the mirror glass.
The hazard lamps operate on battery voltage. The HAZARD fuse supplies battery voltage to the turn signal switch. When the hazard switch is pressed, the turn signal switch sends battery voltage to the hazard lamp/turn signal flasher, which sends an on-off signal to the turn signal switch. The turn signal switch send the on-off signal to all the turn signal lamps, causing all the lamps to flash including both IPC turn signal indicators. The hazard lamp/turn signal flasher is grounded at G200.
When the parklamps are ON, the sidemarker lamps receive voltage from the park lamp supply voltage circuit and illuminate. The sidemarker lamp is grounded through the corresponding rear turn signal. When the turn signal switch is place in the left or right hand position, the rear turn signal illuminates and the sidemarker lamp will loose its ground, causing the sidemarker lamp to turn off when the turn signals are on and to illuminate again when the turn signal is off.
Which blub an socket did you replace ? check the other blub ? The switch and or the flasher module can cause this problem .
Replace the turn signal switch. Refer to Multifunction, Turn Signal, and Hazard Switch Replacement - On Vehicle in Steering Wheel and Column.
Did you complete the replacement?

Which

Oct 11, 2015 | 2001 Pontiac Montana

1 Answer

How do I change the front side marker light bulbs?


Bi-Xenons - 6000K D1S
High Beams - Osram Nightbreakers H7
Fogs - PIAA H11 Yellow Ion
Cornering Lights - Osram Nightbreakers H3
Front Park Lights - High-Powered LEDs with built-in resistors
Front Signal Lights - Sylvania Silverstar 7507A ST (Silver Bluish but lights up Amber)
Front Sidemarkers - InviSilver W5W (Silver but lights up Amber)
Rear Signal Lights - P21W Stealth Bulbs (Silver but lights up Amber)
Reverse Lights - Sylvania Silverstar 7506ST or Error-Free LEDs
License Plate Lights - C5W Error-Free High-Powered LEDs
  • Turn the engine off and approach the side of the porsch with the burn-out side-marker light. If you are replacing both, start at either side; the replacement procedure is the same.
  • 2 Remove the screws from the plastic fender liner. Peel back the liner to access the area behind the fender.
  • 3 Reach your hand inside to gain access to the side-marker light's backing. Push the backing forward to release the side-marker lens; it's held in place by small clips.
  • 4 Grab the lens on the outer side and turn it over to access the back. Gently turn the bulb to release it from the plastic lens.
  • 5 Pull the bulb straight out to remove it from the electrical socket. Insert a new bulb, but do not touch the glass part of the bulb with your hand.
  • 6 Push the new bulb into the side-marker lens. Turn it clockwise to install it. Push the side-marker lens back into place. Apply gentle pressure to the lens to pop it back into its mount.
  • 7 Replace the screws along the edge of the fender liner.


  • Dec 04, 2010 | 2006 Porsche Cayenne

    1 Answer

    Need to replace the headlight assembly on front passenger side do i have to take off the bumper? for ponitac vibe 2003 also have dent on the area


    Yes you do. This is the steps to do that to replace the entire headlight assembly:


    Remove the front fascia.
    • Remove the front fascia extensions, if equipped.
    • Remove the front fender liners.
    • Remove the fog lamps.
    • Remove the bolts (4) from the front bumper fascia (3) at the fender.


    506bafd.gif

    Remove the bolts from the front bumper fascia at the fender



  • Remove the push-in retainers (2) from the bumper fascia using J38778.
  • Remove the fascia bolts (1) from the fascia.
  • Remove the fascia from the vehicle.
  • Remove the 3 bolts which secure the composite headlamp.


  • 7f1ec16.gif

    Remove the 3 bolts which secure the composite headlamp



    1. Remove the sidemarker bulb electrical connector.
    2. Remove the sidemarker bulb, if necessary.
    3. Remove the composite headlamp assembly from vehicle.

    To install:

    1. Install the sidemarker bulb to the composite headlamp, if removed.
    2. Connect the sidemarker bulb electrical connector.
    3. Secure the composite headlamp to the vehicle with the 3 bolts. Tighten the headlamp mounting bolts to 89 inch lbs. (10 Nm).
    4. Install the front fascia.
    5. Install the headlamp bulb to the composite headlamp, if removed.
    6. Fasten the headlamp bulb retainer clip.
    7. Install the socket to the headlamp bulb.
    8. Install the rubber cover to the composite headlamp.
    9. Aim the headlamps.
    10. Close the hood.

    Oct 12, 2010 | 2003 Pontiac Vibe

    1 Answer

    2000 pontiac montana. I want to replace the driving ligh bulbs. the under the headlights what size is it?


    Fog/Driving Light Bulb Size: 880
    Here is the rest of the bulb size used in your Montana.
    2000 Pontiac Montana Auto Light Bulb Diagram
    Low Beam Headlight Bulb Size: 9004
    High Beam Headlamp Light Bulb Size: 9004
    Parking Light Bulb Size: 4157NALL
    Front Turn Signal Light Bulb Size: 4157NALL
    Rear Turn Signal Light Bulb Size: 3156
    Tail Light Bulb Size: 3057
    Stop Light Bulb Size: 3057
    High Mount Stop Light Bulb Size: Assembly
    Fog/Driving Light Bulb Size: 880
    License Plate Light Bulb Size: 168
    Back Up Light Bulb Size: 3156
    Front Sidemarker Light Bulb Size: 194
    Ash Tray Light Bulb Size: 558
    Glove Box Light Bulb Size: 194
    Map Light Bulb Size: 168
    Dome Light Bulb Size: 562
    Step/Courtesy Light Bulb Size: 168
    Trunk/Cargo Area Light Bulb Size: 212-2
    Daytime Running Light Bulb Size: 3157NALL
    Thank you for using fixya.


    Apr 30, 2010 | 2000 Pontiac Montana

    1 Answer

    Which bulb is for the taillamp/stoplamp/turn siganl lampand which fuse ?? 2005


    2005 CHEVROLET Malibu
    Low beam headlamp
    H11

    High beam headlamp
    H9

    Parking light
    3157

    Front turn signal
    3157

    Rear turn signal
    3057

    Tail light
    3057

    Stop light
    3057

    High mount stop light
    912

    Fog/Driving light
    880

    License plate
    194

    Back up light
    921

    Front sidemarker
    24

    Rear sidemarker
    194

    Ash tray
    161

    Glove box
    194

    Map light
    168

    Dome light
    561

    Step/Courtesy light
    168
    37

    Trunk/Cargo area
    211-2
    http://www.sylvania.com/ConsumerProducts/AutomotiveLighting/LampReplacementGuide/AutoLRG-Results.htm
    You can find all auto bulb info here.As far as the fuse there should be a fuse diagrahm on the back of the access door.Well hope this helps.

    Mar 26, 2010 | 2005 Chevrolet Malibu

    1 Answer

    Raplacing a drivers side front marker light.


    To replace the sidemarker light on a 96 Towncar, raise the hood and open the black plastic flap behind the header panel on that side. There is a 11mm nut down about 5" on the side. Remove it. The screw is on the outside just past the plastic lens. Pull the light out far enough to unscrew the bulb socket.

    Oct 05, 2009 | 1996 Lincoln Town Car

    1 Answer

    NEED TO REPLACE A TAIL LIGHT BULB IN A 2005 CHEVROLET IMPALA


    and Repair Notes TAIL LAMP REPLACEMENT REMOVAL PROCEDURE Open the rear compartment. Remove wingnut and pull back the rear compartment trim panel from the tail lamp. Remove the wingnuts from the tail lamp. Remove the tail lamp from the rear body panel. Disconnect the electrical connector from the tail lamp. Remove the tail lamp socket, turning counterclockwise. Remove the bulb from the tail lamp socket. Remove the sidemarker lamp socket, turning counterclockwise. Remove the bulb from the sidemarker lamp socket. INSTALLATION PROCEDURE Install the bulb to the tail lamp socket. Install the bulb to the sidemarker lamp socket. Install the sidemarker lamp socket, turning clockwise. Install the tail lamp socket, turning clockwise. Connect the electrical connector to the tail lamp. Install the tail lamp to the rear body panel. Install the wingnuts to the tail lamp. Pull back the rear compartment trim panel to the tail lamp and install the wingnut. Close the rear compartment.

    Jun 08, 2009 | 2005 Chevrolet Impala

    1 Answer

    "where is the Horn Location for 2001 Chevrolet Malibu"


    Horn Replacement Removal Procedure
    1. Remove the right headlamp assembly. Refer to Headlamp Assembly or Headlamp Bulb and/or Cornering, Sidemarker, Park, Turn Signal Bulb Replacement in Lighting Systems.
      794212.gif
      tif.gif
    2. Disconnect the horn electrical connector.
    3. Remove the horn bracket bolt.
    4. Remove the horn from the front frame rail.
    Installation Procedure

      794212.gif
      tif.gif
    1. Position the horn to the front frame rail. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
    2. Install the horn bracket bolt. Tighten
      Tighten the bolt to 10 N·m (89 lb in).
    3. Connect the horn electrical connector.
    4. Install the right headlamp assembly. Refer to Headlamp Assembly or Headlamp Bulb and/or Cornering, Sidemarker, Park, Turn Signal Bulb Replacement in Lighting Systems.

    May 17, 2009 | 2001 Chevrolet Malibu

    2 Answers

    How do you change a headlight on a 2006 kia sedona?


    Left front low or high beam headlight: remove battery, remove weather cap, pop-off 2-prong connector, depress spring holding bulb in position, use inspection mirror if necessary, one end of spring is caught beneath a lip, Move spring past lip and lift up, it will rotate upward and is fastened on opposite side. Remove old bulb, install new 55 watt halogen bulb (H7-55) available at Walmart. Install new bulb with tang in slot at bottom, fold over spring and depress to hook end under latch point, install 2-prong electrical connector, install weather cap, turn about 1/8 turn to lock into position. Reinstall battery, clean terminals and cable ends, place new no-corrode rings (available from Walmart) around battery posts, install cable ends, and tighten.

    Right front headlights: not necessary to remove battery, otherwise same essential procedure.

    Note: Lower and upper beams all use same H7-55 bulb.

    Jul 24, 2008 | 2002 Kia Sedona

    Not finding what you are looking for?
    1994 Toyota Pickup Logo

    Related Topics:

    84 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Toyota Experts

    yadayada
    yadayada

    Level 3 Expert

    75822 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8210 Answers

    Are you a Toyota Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...