Question about Chevrolet Corvette

1 Answer

The clutch is a few inches above the break peddle. It's a hydralic clutch and selfadjusting. I would like it lower Thanks Larry L

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 4,793 Answers

Not sure this is the right answer but how much movement have you got with the clutch pedal before you feel any resistance...if its a couple of inches has the pedal stop rubber fallen out above the pedal.??

Posted on Sep 11, 2010

Testimonial: "Hi Although that was not the exact problem it sent me in the right directiion. It saved me alot of time and money and it was a related problem. "

  • lavallee10 Sep 11, 2010

    I wasn't finished.
    Thanks aloy

  • lavallee10 Sep 11, 2010

    I meant thanks alot.
    Fixed the can in under 30 minutes.
    It's a Corvette so it wasn.t easy
    Thanks again

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What can I do to adjust clutch cable on my 1989 LeBaron?


Just push and then lift the clutch pedal toward you to adjust the cable. The mechanism is above the clutch pedal and is selfadjusting as liong as you lift the pedal. If that don't work then the adjust mechanism is junk.

May 01, 2014 | 1989 Chrysler LeBaron

5 Answers

Brake and gas peddle


U should pull the break strap it may balanced the height.

Jun 17, 2008 | 2008 Ford F-350

1 Answer

I own a 1995 Audi 90cs. My clutch peddle started being dead tell half way down then got preshure. Now there is no preshure and the peddle sticks to the floor. There was no slipping in the clutch so I


You need to replace the clutch slave.....Ii recently did mine, after the installation it was stuck too.......the way I fix it was I had a friend pumping the clutch by hand while I bleed it under the car, it took about 15-20 minutes before it got hard again.
Good luck!

Aug 01, 2012 | 1995 Audi 90

1 Answer

Why would there be a rattle noise when in neutral and grind going into first gear?


Your slave cylinder in your ****** or your master cylinder could be bad. Both are integral parts of your transmission. The master cylinder is a hydralic hose that goes from your clutch peddle down into the bell housing and connects to the slave cylinder which disengages or engages your clutch. I had to replace both of mine because the mount for the slave cylinder broke and my master cylinder was bad. Them master cylinder is located directly behind the firewall in the engine compartment and connects to your clutch via a rod that connects to the top of your clutch peddle. check the fluid level in the master cylinder first and formost to see if you are just simply low on fluid if you are then DOT 3 brake fluid works perfectly fine for it.

Mar 15, 2012 | 1999 Mitsubishi Eclipse

1 Answer

Convertible top not going up.


LISTEN FOR HYDRALIC PUMP MOTOR OPERATION IN THE TRUNK AREA..IF YES YOU HEAR HYDRALIC PUMP MOTOR RUNNING MAKING A NOISE.CHECK HYDRALIC PUMP FLUID LEVEL BY REMOVING THE SCREW TYPE CHECK PLUG.PLACE RAGS UNDER THE CHECK PLUG.AND UNSCREW REMOVE THE CHECK PLUG. FLUID SHOULD BE 1/4 INCH BELOW THE CHECK PLUG HOLE.IF FLUID IS LOW ADD FLUID UNTIL FLUID LEVEL 1/4 INCH FROM THE PLUG HOLE.IF HYDRALIC FLUID WAS WAY LOW YOU NEED TO BLEED AIR OUT OF THE SYSTEM.MAKE SURE FLUID LEVEL CORRECT.START ENGINE AND TRY RAISING AND LOWER THE CONVERTIBLE TOP USING THE SWITCH.IF TOO MUCH AIR GOT IN SYSTEM.HAVE A HELPER WORK UP AND DOWN CONTROL SWITCH WHILE YOU MANUAL OPEN CLOSE CONVERTIBLE TOP BY HANDS BLEEDING AIR OUT OF SYSTEM.KEEP EYE ON HYDRALIC FLUID LEVEL WHILE BLEEDING THE SYSTEM..LOWER THE TOP AND TURN OFF ENGINE. BEFORE OPENING THE HYDRALIC PUMP FLUID CHECK PLUG BECAUSE FLUID WILL SPRAY EVERY WHERE..IF HYDRALIC PUMP CHECK OUT OKAY AND YOU DO NOT HEAR NO HYDRALIC PUMP NOISE.POWER IS GOING TO HYDRALIC PUMP.EITHER HYDRALIC PUMP MOTOR FAULTY OR FAULTY HYDRALIC PUMP RELAY BEST TO LET MERCEDES BENZ DEALERSHIP CHECK IT OUT...

Apr 30, 2011 | 2005 Mercedes-Benz Mercedes Benz SLK350

1 Answer

I'm not sure if that's the problem. We where driving and the car started jerking. Now the clutch peddle has no pressure. I can push the peddle in real easy but I have to pull it out by hand. There's no...


CHECK CLUTCH MASTER CYLINDER RESERVOIR SOUND LIKE ALL BRAKE FLUID LEAKED OUT.CHECK ALL HYDRALIC LINES FOR LEAKS TO BRAKES AND CLUTCH MASTER CYLINDER TO CLUTCH SLAVE CYLINDER.REASON NO PRESSURE AIR WILL ENTER THE HYDRALIC SYSTEM WHEN FLUID LOW AND LEAK OUT.

Dec 25, 2010 | Chevrolet Cavalier Cars & Trucks

1 Answer

Clutch looses pressure, leaking by clutch peddle


Clutch master cylinder is leaking out of piston cup.Detach from clutch pedal, disconnect hydralic line, and remove 2 firewall retaining bolts or nuts and pull out. Replace clutch master and bleed line at clutch slave cylinder.

Dec 13, 2010 | 1992 Nissan Pickup

1 Answer

1992 Ford F250 4x4 7.3 Diesel


those trucks had problems with the fire wall breaking .have some one push the clutch pedle and watch the fire wall from under the hood were the clutch master cylinder bolts too if the fire wall moves u need to buy the repaire kit from ford.

Apr 01, 2009 | 1992 Ford F250

1 Answer

Replaced clutch but pedal will not move down at all now on 98 chevy 1/2 ton 2wd


Sounds like the release bearing is in backwards! No check valve. If the peddle was pushed, it would pop the slave cylinder piston. 2/ The clutch disc could be in backwards too! Either way, you will need to pull the tranny! Sorry! Frankster016

Oct 22, 2008 | 1998 Chevrolet K1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

82 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...