Question about 1997 Chrysler Concorde

Open Question

I need to know how to replace a front cradle bushing on my 1996 Chrysler Concord. Thanks so much

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2039 Answers

SOURCE: 1996 chrysler concord lx problem

burn fuse check them out one by one thank you for using fixya pierre

Posted on Jun 23, 2008

Ad
  • 29 Answers

SOURCE: 2004 Nissan Quest front control arm bushing replacement.

You can get just the bushings at autozone, checker, napa auto part stores for about $30.00 to $35.00. You can replace them yourself or take the vehicle to the shop.


GGBMDB

Posted on Nov 30, 2008

jgwhomeequip
  • 1902 Answers

SOURCE: DHOW TO CHANGE OUT HEADLIGHT BULB ON 1996 CHRYSLER CONCORD LXI

For the bulb removal follow these steps.
-Open the hood and look behind the headlamp assembly with the burned out bulb.
-You'll see a black plastic ring about 2 inches in diameter, rotate this a quarter turn.
-Unplug the bulb, gently pulling the clip up to release the bulb.

Posted on Feb 05, 2009

csmock132
  • 4669 Answers

SOURCE: replace the engine motor mounts and the transmission mount. Would like to know how to do it. Thanks.

Check the frame mounts too. You will have to loosen the bolts and jack the motor up with a jack and a woodblock.

Posted on May 04, 2009

emissionwiz
  • 76691 Answers

SOURCE: 1996 Chrysler Concord turns over but won't start.

U will need to buy a fuel pressure test gauge, about $25-$5, to hook this up go to the top of the engine and u will see a supply rail that fits over the top of the fuel injectors, in the pipe/rail there is a test port valve, it should be fairly easy to spot, the gauge goes there, crank the engine and u should have around 45-50 PSI of fuel pressure.

Posted on Jun 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What do I fix to stop left and right sway on my 1996 Seville concord


Get a front wheel alignment? It sounds like you have tow-out instead of tow-in. Tie rod ends may be loose, or bushings and/or ball joints may need replaced. Perhaps shocks too.

Apr 18, 2017 | Cars & Trucks

1 Answer

WHAT IS THE KM. LIMIT FOR SUB FRAME RECALL


I was the one posting all over the internet about the letter Chrysler sent me but it doesn't do any good. If the car was from the rust prone states and was built in a few months during a certain year they will replace it. I got mine replaced under the care warranty I bought when I got the car but after a month they sent me a letter that they were covered for 150,000 miles and returned my co pay. Then my other Pacifica cradle went out and I called and told them I would sue them if they didn't replace it and I would have. It cost me 250 dollars on the second Pacifica. There is no recall at the time because no one has died yet from the engine and transmission dropping to the ground and losing the steering and brakes ( the brake lines go across the cradle) The dealership that replaced the cradle forgot the large washers that hold the rubber bushings that hold up the cradle and as I was driving I lost all steering as the rubber bushing ripped out of the engine cradle in the back the cradle was an inch off the ground. The dealer said it was their best man and he would never forget the washers. It was towed back to the dealer and all new parts were put on for free but I bet Chrysler didn't know anything about it. If I had been on the expressway like I was earlier in the day I could have been killed

4a63ce51-fd37-4f84-bf29-6272b445c06d.jpg

Sep 15, 2015 | Chrysler Pacifica Cars & Trucks

2 Answers

2004 chrysler pacifica is clunking on very small bumps. Not during braking though. I've looked at struts and they seem okay. Nothing loose that I can see or feel. Ideas?


JACK UP THE FRONT OF THE CAR AT THE FRAME TILL THE TIRE IS OFF THE GROUND.THEN TRY MOVING THE STRUT AND THE SPRING!!ALSO LOOK AT THE SWAY BAR LINKS CONNECTED TO THE LOWER A ARM OR STRUT!!

Nov 16, 2013 | Cars & Trucks

1 Answer

My 96 Chrysler Concorde clunks hard when I hit the gas or turn. What could this be? and is it unsafe to drive?


That's not enough information.

Suspects include:
1.) Cradle bushings
2.) Engine and/or Transmission Mount(s)
3.) Axle shaft CV joint(s)

Feb 25, 2012 | 1996 Chrysler Concorde

1 Answer

Where is the cradle frame in a 1996 oldsmobile 88 ?


You may be referring to the engine cradle mount. We were just told ours was bad. Upon my own inspection, the 4 bushings/washers/bolts parts are worn/missing. If you look just behind front wheels, you will see those bushings plainly.

Apr 19, 2011 | 1996 Oldsmobile 88

1 Answer

What Are The Dangers Of Driving A Concorde With Bad Cradle Bushings


The dangers are the alignment can change in a flash,so be careful.

Aug 20, 2010 | 1996 Chrysler Concorde

6 Answers

I have a 2004 pacifica, fwd. I had just gotton my front brakes and rotors done, as well as all tie rods. I am still a wierd knocking noise in the front end (sounds like the right wheel well mostly) Almost...


In this order stabilizer links, stabilizer bar bushings, control arm bushings, engine cradle bushings or bad struts mine have 160,000 and don't clunk but do need replacement
9_23_2015_9_24_08_pm.jpg

Aug 11, 2010 | 2004 Chrysler Pacifica

1 Answer

Need to know how to replace lower control arm


LOWER CONTROL ARM

REMOVAL
1) Raise and support vehicle. 3) Remove the steering knuckle.
Remove the bolts fastening the power steering cooler to the front suspension cradle crossmember reinforcement (Fig. 21). 5) Remove the lower control arm rear bushing retainer bolts located on each side of each lower control arm rear bushing. NOTE: The bolts fastening the cradle crossmember reinforcement are of three different thread sizes. Note the location of the various sizes.

6) Remove the bolts attaching the cradle crossmember reinforcement to the front suspension cradle crossmember (Fig. 22). Remove the 2 bolts fastening the reinforcement and rear of cradle crossmember to the body of the vehicle. Remove the reinforcement. 7) Remove the pivot bolt attaching the front bushing of the lower control arm to the front suspension cradle crossmember. 8) Remove the lower control arm.

Sep 25, 2009 | 2006 Dodge Caravan

1 Answer

1996 chrysler concord lx problem


burn fuse check them out one by one thank you for using fixya pierre

Jun 23, 2008 | 1996 Chrysler LHS

Not finding what you are looking for?
1997 Chrysler Concorde Logo

Related Topics:

189 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...