Question about 1986 Ford F 250

1 Answer

I have a 86 ford 250 diesel the break pedal goes to the floor but will stop the truck I replaced the booster what else can I do to get better breaks

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    MVP:

    An expert that gotĀ 5 achievements.

    Master:

    An expert who has achieved Level 3.

    Sergeant:

    An expert that hasĀ over 500 points.

  • Master
  • 449 Answers

If you havnt already change the mastercylinder

Posted on Sep 11, 2010

  • robertbri320 Sep 11, 2010

    I have not, do you thank that the master cylinder would effect my pedal

  • Ralph Cronenberg Sep 11, 2010

    yes most likely this is your problem

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1998 ford expedition booster new master cylinder new all disc break new break peddle goes to floor after bleeding hole system


You can bleed the system all you want and STILL have the pedal go to floor unless the master cylinder was bench bled in a vice BEFORE it was put on the vehicle. ALWAYS bench bleed a master cylinder before you put it in service. If you don't, you'll never get the pedal off the floor.

Nov 11, 2017 | Ford Cars & Trucks

3 Answers

Even after replacing front and rear brakes, the pedal goes nearly to the floor (but does stop the vehicle). What do I need to do


Brake booster has gone bad or u have a vacuum leak. Check the seals for leaks around booster where the. Fluid goes in the plastic holder. Check for vacuum leak going to break booster

Apr 15, 2015 | 1999 Plymouth Breeze

1 Answer

Breaks spongy go all the way to floor before a slowly loud grinding stop


Some ABS equipped vehicles require a scanner to activate ABS valves to allow for proper bleeding of air.

Feb 17, 2013 | Cars & Trucks

2 Answers

When i push down on the brake pedal air leaks out around the rod and the pedal goes to the floor.


Check the vacuum line on the power brake booster, the diaphram may be pushing the air down the rod, the break booster may be defective all together if the vacuum line is intact.

Mar 30, 2011 | 1983 Ford Thunderbird

1 Answer

Hi, I have a 1981 VW jetta diesel. While I was driving, the break pedal started to get stiff. Now the pedal does not depress, it just stays at the top and I have no breaking power. I suspect the master...


Sounds to me like your brake booster is bad. Does the car still stop even though the pedal is hard when you step on it?If so that's most likely it

Jan 06, 2011 | 1983 Volkswagen Jetta

1 Answer

My break pedal goes all the way to the floor....i have a 94 pontiac bonneville.....and i read a few things on you website.....i added break fluid but they still go all the way to the floor....do i have to...


You either have air in the line or your vacuum booster needs replaced. Try to bleed them first. Then pull the vacuum line of the booster and see if it makes a change. Good luck.

Nov 20, 2010 | 1994 Pontiac Bonneville

1 Answer

I have a 96 f250 powerstroke that had not much breaking so i replaced the master cylinder the power booster the driver caliper(due to broken bleeder) the coil line off the master cylinder for the front and...


Most diesels use a belt driven vacuum pump to supply brake booster vacuum. See if vacuum is present at the hose on the booster can fitting. that is an old vacuum pump(1996) replace it.

May 24, 2017 | Ford F-250 Cars & Trucks

1 Answer

I have a 96 ford explorer xlt 4wd with ABS. When I bought it it had a broken back break line. I replaced the line blead the breaks and the breaks are spongy. I googled the issuse and found out it could be...


Check your parking brake. if it goes down to the floor or does not hold, then your back brakes needs adjusted. bad master cylinders bleed off slowly to the floor while pushing on the brake pedal. If you need assistance on adjusting let me know.
Randy

Nov 09, 2010 | 1996 Ford Explorer

2 Answers

97 ford e350 brake pedal goes to the floor...


are your rear drums set up? why did you bleed the brakes. when only when you installed new pads?

Sep 11, 2008 | 2002 Ford E350

2 Answers

Breaking


there is a big rober hose by the power booster start the car up and then turn the car off then unplug the hose if you hear like air the the booster is ok but if not then most likelly the powwer booster is not good

May 27, 2008 | 2002 Pontiac Grand Prix

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

108 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

fordexpert

Level 3 Expert

5581 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...