Question about 1997 Buick LeSabre

1 Answer

How to bleed brakes on a 1997 buick lesabre - 1997 Buick LeSabre

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

When the brake peadal is pushed a swishing noise is heard around the brake pedal rubber boot

Posted on Nov 12, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

DID ANY 1997 BUICK LESABRE HAVE HYDRO-BOOST BRAKE SYSTEM


Nothing to do with ac system caliper seize or brake hose change both of them

Apr 02, 2015 | 1997 Buick LeSabre

1 Answer

1994 buick lesabre new master cylinder abs light on


Look for a bleeder on ABS HCU unit- the one with brake tubing

Drive it & then Bleed again

Have to hear the abs pump come on,check fuse for it

If that doesn't work may have to open the
hcu with an obd1 scan tool & bleed

Feb 01, 2013 | 1994 Buick LeSabre

1 Answer

How do i replace a power brake booster on a 1997 buick lesabre


Usually you unbolt the master cylinder, disconnect the brake pedal rod, then unbolt the booster from the firewall.

Aug 04, 2012 | 1997 Buick LeSabre

1 Answer

2000 buick lesabre with abs-low brake pedal after changing all 4 rotors and pads. did not open the hydraulic system


When changing pads and you push the caliper in for the new pad you should open the bleed screws. , then close and re-assemble. press pedal and open bleed screw and let it drip a little . gravity bleed. Did you turn the read caliper piston in and then press it down? The rear piston must be aligned with the pad. Did you pump the parking brake to reset?

May 20, 2011 | 2000 Buick LeSabre

1 Answer

Still cant get a brake pedal.. been bleeding the lines but not getting much out of them. replaced master cylinder, still no pedal. has all new lines also


you may have to run the motor as you bleed the brakes so the abs hydraulic unit can purge any air that might be caught within the unit itself.did you bench bleed the master cylinder before installing it on the car.this can save time and reduce the possible chance of air entering the system.make sure you don`t allow the master cylinder to run low on brake fluid.i also assume that you are bleeding the brakes properly.Left front brake works with Right rear brake and Right front brake works with Left rear brake.this is how the brakes should be bleed.

Mar 15, 2011 | 1997 Buick LeSabre

1 Answer

Bleeding front brakes and brake pedal still goes to floor board


Must bleed all four brakes to determine if there is air in the lines.

If after bleeding several times, the brake pedal still goes to the floor board, the master cylinder may be determined to be bad.

Aug 12, 2010 | 2002 Buick LeSabre

1 Answer

Bleed the brakes on 2002 buick lesaber need to power bleed?


Not really. Works better but if you are going to manually bleed brakes start at the farest point. 1) RR 2) LR 3) RF 4) LF don't forget to check brake res. and refill as needed. I am assuming you know how to bleed brakes.

Jul 05, 2009 | 2002 Buick LeSabre

1 Answer

1992 Buick LeSabre brakes bleed but very lil brake at pedle


start bleeding your brakes from the rear wheels and work your way to the front. I'm assuming you already did a pad change since you say you got the air out. make sure you keep the fluid level and not let it get too low while you're bleeding them or air will get into the master cylinder and you have to start all over again. Make sure you have someone help you that is competent enough to hold the brake pedal down all the way and not let off even the slightest bit until you get the bleeder screw tightened.

Feb 03, 2009 | 1992 Buick LeSabre

1 Answer

No brakes in my 1998 buick leSabre


running master low enought for brake light to come on, you might have got air into system, if that is the case you will have to bleed out the breaks. worse case, it would need a new master cyl.

Jan 18, 2009 | 1998 Buick LeSabre

Not finding what you are looking for?
1997 Buick LeSabre Logo

Related Topics:

367 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6918 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...