Question about 1996 Ford Aspire

1 Answer

Do you have a manual for replacing clutch for 1996 ford aspire step involved in replacing clutch

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

I just replaced mine and I used the Hayes (haynes?) manual. was about 20 bucks from parts store.

Posted on Mar 01, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can you please send me the step by step of how to replace the timing belt in my 1996 alero LSS oldsmobile


very involved
better if you get a workshop manual as there are photos as well as the procedure to follow

Jun 23, 2017 | Oldsmobile Cars & Trucks

1 Answer

What can cause a 1996 ford ranger no to be going in gear when the vehicle start. It has a manual gear box


if you have replaced the clutch , t will be a clutch plate put in back to front
If it is hydraulic clutch ,it will be a master cylinder or slave cylinder problem
if it is cable clutch , it will be a failed clutch cable

Mar 09, 2016 | 1996 Ford Ranger SuperCab

1 Answer

How do I replace and install manual clutch?


I Suggest you get repair manual,there is alot involved.If you never did a clutch on anything I hope you have a freind that has changed a clutch. It would take an hour to write it all down!

Oct 02, 2014 | 1996 Honda Passport

1 Answer

How do you replace clutch in 1996 rav4


There are a lot of steps involved in this to do it correctly not counting the obvious, you have to pull the transmission. I recommend you get the Haynes or Chiltons Repair manual on your vehicle for step by step directions and recommendations on tolls, special or otherwise. The new assembly should come with any guides, that is a bearing guide or clutch alignment guide, that might be needed.

Sep 08, 2010 | 1996 Toyota RAV4

2 Answers

Change the clutch out of a 1995 ford


due to the amount of work involved and specs. get a haynes or chiltons repair manuel and follow step by step. any parts store has them for around twenty bucks. berrydalewolf

Oct 29, 2009 | 1995 Ford Aspire

1 Answer

I need on line help to replace my cluch on a 1996 step by step


this is very easy, you shouldnt need any help
bear in mind there is 2 sizes of clutches, if you have 4x4 i think it was 254mm but not sure

Aug 09, 2009 | 1996 Ford Ranger SuperCab

1 Answer

My CV's are clicking and i need to replace them what are the steps to replace both the Passenger and drivers side?


I've never changed cv joints on a Ford, but my experience w/ other vehicles has been the realization that it's a tough job, lots of labor involved. You can do it, but u really have to get a good repair manual so u can see illustrations, and follow the many steps involved. Pick up a Haynes or Chilton manual (available online, or many parts stores), or subscribe to an online repair source like e-mitchell. To list all that's involved here would take too much time and space. Good luck, u can do it! countrycurt0

Oct 05, 2008 | Ford Laser Cars & Trucks

1 Answer

Need step by step on how to bleed hydrolic clutch on a 1996 ford ranger


First remove the clutch reservoir top. Make sure the rubber stopper/bladder is in the cap when removed. Next locate the clutch line that goes into the tranny just aft of the bell housing. There should be a bleed screw, if so open it slightly. If no screw, than loosen the line where it attatches in. Next fill the clutch reservoir and watch till it leaks out on the tranny end. Once thats noticed, close the screw/line and recap reservoir. pump clutch pedal, and repeat bleed steps at least once more to ensure all air is out. remember to fill clutch fluid up to operating levels.

Jul 20, 2008 | 1996 Ford Ranger SuperCab

1 Answer

Replacing a clutch


3 to 5 hrs if you dont have any problems.

Jul 19, 2008 | 1996 Ford Aspire

Not finding what you are looking for?
1996 Ford Aspire Logo

Related Topics:

114 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...