Question about 2002 Saturn SC

1 Answer

What size are the smaller head bolts located around the timing area. They look like the have star heads on the and a 10mm slips

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 13 Answers

It's not a standard socket ther torques sockets you can get a set for about 30 bucks at most parts stores get the metric set most of the saturns use 10 12 mm torques and higher

Posted on Sep 11, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What tool is used to open the head bolts on a citroen xsara picasso


Special tool like Torx key. Use the ones that can be inserted into a size 10mm bolt socket. I think it's size T50.

May 03, 2014 | 2004 Citroen Xsara Picasso

1 Answer

Bolt size for 2008 ford focus side mirror


Thread size is 8mm 10mm is the head size meaning you use a 10mm socket

Apr 01, 2013 | 2008 Ford Focus SE Sedan

1 Answer

2003 dodge intrepid sxt 3.5 over heated replaced the thermostat and still over heats might be water pump where is it located and what is in volved in fixing this


The water pump is located in the front of the engine & is driven by the timing belt. So if you go in there you might as well replace the belt and tensioners if needed.
Drain the cooling system (turn the radiator drain 1 full turn only)
  1. Remove the upper radiator hose
  2. Remove the top radiator support
  3. Remove the two 10mm head bolts from either side of the radiator and gently pull the top of the radiator forward to gain a little more room
  4. Remove the four 10mm head bolts holding the cooling fan module to the radiator . Remove the four clip nuts and the cooling fan electrical connector and lift the fan module out of the vehicle
  5. Loosen and remove the drive belts and remove the three 13mm head bolts holding the alternator belt tensioner pulley to the timing cover
  6. Remove the three piece timing belt cover (the lowest piece can be accessed through the crankshaft pulley by turning the pulley and removing the bolts)
  7. turn the crankshaft pulley and line up the timing marks on top dead center
  8. Remove the timing belt tensioner two 13mm bolts and remove the tensioner (If the tensioner pulley wheel is made of plastic you will want to purchase a revised steel tensioner pulley) . Put the tensioner in a suitable vise to compress it and install a small allen wrench from the front to hold it in place (close the vise slowly to compress the tensioner)
  9. (If need be) Remove the plastic tensioner pulley (the 15mm head attaching bolt can be removed without removing the crankshaft pulley)
  10. The timing belt can easily be slipped under/around the crankshaft pulley by slightly bending it to the outside of the timing belt housing on the drivers side and working it with your hand through the crankshaft pulley . No excessive force is needed to do this and be sure to clean the area well prior to installing the new belt
  11. With the belt removed , remove and replace the water pump . Coat the gasket with a little RTV silicone and clean the gasket mating surface well
  12. Install the timing belt in the opposite direction as removed . Make sure that all the timing marks are lined up .
  13. Reinstall the timing belt tensioner

    Note: There are several different length bolts used, so pay attention to where they are removed from, they must be installed in the same placement.

    I hope this information was helpful.

Sep 17, 2011 | 2003 Dodge Intrepid

1 Answer

What size bolt holds the water pump on a 1989 4.5 litre caddy sedan deville


Hello: There are 3 15mm bolts 10 10mm bolts and two round bolts with a star insert in the bolt head (like a allen head only this star shaped. Also may have 1 15mm stud depending on configuration.

Nov 03, 2010 | 1989 Cadillac Sedan DeVille

1 Answer

SIZE OF THE TRANNY PAN BOLT FOR A 1998 BUICK LESABRE


The size of the bolt or the size of the head? The bolts heads are 10mm. I think the bolts are 8mm X 1.25

Jun 15, 2010 | 1998 Buick LeSabre

1 Answer

Where is the cam shaft sensor located on a 8.1 chevy suburban 2002


On the drivers side, behind the cylinder head. It will be rough to get to from the top, I've never tried it like that, but have seen some guys do it.
If you reach back there way down to where the head bolts to the block you will feel it. It is held in by a 10mm headed bolt that is bolted to the back of the cylinder head. The fuel lines are going to be in your way, you are going to have to work around them.

Oct 23, 2009 | 2002 Chevrolet Suburban 2500

3 Answers

1992 Toyota Previa van,Oil dripping onto exhaust manifold, replace head gasket? need a free manual!


The toyota previa uses a formed silicone gasket for the valve cover and the cover is held in place by metric shoulder bolts ( 10mm). The valve gasket leaks because you can't get enough preload on the bolts to re-seat the old gasket when it gets old and shrinks. The shoulder bolts only allow you to tighten the gasket enough to seat the shoulder on the bolt. If you continue to torque down the suspected bolts, you will snap the bolt off ( don't ask me how I know this ). You can either 1.)replace the old gasket with a new one or 2.) remove the existing bolts around the leak area and put in new metric bolts that do not have a shoulder. You may want to put in a small sleeve into the existing bolt hole but shorter than the thickness of the valve cover to account for the smaller diameter bolt. You can now torque down the bolt and get enough preload to seal the valve cover without removing the old gasket. Make sure you use a torque wrench ( in-lbs) or be very careful not to snap these small valve cover bolts.

May 26, 2009 | 1992 Toyota Previa

1 Answer

I want to remove the head light assembly on my 1992 lexus sc400


remove the 2 10mm bolts on top that you can see, then remove front part of inner fender liner you will find 2 10mm nuts. you will need a long extension. Recomend using duct tape around feneder area to avoid scratching.

Mar 21, 2009 | 1992 Lexus Sc 400

3 Answers

Star bit on front brake 2000 chevy 1500 ?


YES THEY COME IN METRIC SIZES. AND,MOST GM PRODUCTS ARE ALL METRIC THESE DAYS. GET A MERTIC SET. YOU WILL ALWAYS USE THEM AGAIN. TOOLS ARE A GOOD INVESTMENT.

Jan 24, 2009 | Chevrolet 1500 Cars & Trucks

Not finding what you are looking for?
2002 Saturn SC Logo

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...