Question about Nissan 200SX

Open Question

I need to replace the water pump on a 96 nissan 200sx

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 840 Answers

SOURCE: replacing belts after replacing water pump on 1996 nissan quest x

the easist way is to loosen the alternator slide the alternator down then slide the belt where it should go then pull up on the alternator again and bolt up Please rate my response thank you very much

Posted on Jan 30, 2009

TheApples
  • 10 Answers

SOURCE: where is ccoling temp sender 1.6 96 nissan 200sx

This is for the 2 litre SR20DET engine so not sure if that's what you have - never heard of a 1.6 version. Below is the exploded diagram and a test for the sensor.

96fe380.jpg

8d1e360.jpg


Posted on Mar 18, 2009

okcfirewall
  • 80 Answers

SOURCE: 96 nissan 200sx is it obd2 ready

yes it has an obd2 diagnostic plug The trouble codes that are required by law on all OBD II systems are "generic" in the sense that all vehicle manufacturers use the same common code list and the same 16-pin diagnostic connector. Thus, a P0302 misfire code on a Nissan means the same thing on a Honda Toyota or Mercedes-Benz. But each vehicle manufacturer also has the freedom to add their own "enhanced" codes to provide even more detailed information about various faults

Posted on Jul 20, 2009

  • 454 Answers

SOURCE: do i need to change my timing chain when i change

Not necessarily. You should at least consider it if you are close to a major service milestone (90k, 120k, etc.). It is a lot of work to change the timing chain (belt), but you have to do some of the work anyway to replace the water pump.

Posted on Oct 23, 2009

Testimonial: "thanks i'm at 150k and how would i know if i need it when i open it up doing work this weekend.thank you"

cda2z
  • 120 Answers

SOURCE: Need to access 96' Dodge neon water pump

the water pump is behind the plastic covers on the right side of engine requires removing the timing belt to replace water pump

Posted on Jul 16, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

THE CLUTCH ON MY 96 NISSAN 200SX SE STICKS WHEN I SHIFT AND ONLY HAS A LITTLE PAY WHERE THE CLUTCH ENGAGES


Could be clutch cable adjustment needed. Could be bad clutch cable bad or linkages to. If noisy bad throughout bearing. How many miles on clutch? could be worn out and need to be changed.

Mar 06, 2015 | 1996 Nissan 200SX

1 Answer

How do I remove the lower front control arm on a 96 Nissan 200sx


put on jack stands, remove tire, remove brake caliper and bracket, detach outer tie rod end, remove axle bolt, remove hub bolts from strut, tape on axle with hammer to remove it from hub, loosen lower ball joint bolt, use fork tool to brake joint loose, remove hub and bearing, remove stabilizer links, remove bolts on lower control arm, replace every thing in reverse

Feb 01, 2015 | 1996 Nissan 200SX

1 Answer

Will a spare tire from a 88 ford escort fit on an 96 Nissan 200sx se-r both 4 lug


check the size on the tyre's side wall , and the wheel size which is stamped on the wheel by the bolt holes , outside face.

Jul 23, 2014 | 1996 Nissan 200SX

1 Answer

Will a spare tire from a 88 Ford escort fit on an 96 Nissan 200sx se-r


no sorry different patterns
88 ford escort 13 inch 4x108
96 Nissan 200sx se-r 15 inch 4x100

Jul 23, 2014 | Cars & Trucks

1 Answer

I have a 96 Nissan 200SX I need help please


Sounds like a fuel pressure problem, either the pump or the filter among other things.

Jul 07, 2012 | 1996 Nissan 200SX

1 Answer

Nissan sentra 200SX cranks over but won't start


check fuel pump, fuel pump fuse, distributor,and ignition coil please. then you will need to check crank position sensor.(to do this you need to find factory service manual)

Nov 23, 2011 | 1996 Nissan 200SX

1 Answer

Hello, My 96 nissan 200sx ac only works on num 4, is it a bad switch are what?


It's the diode block. The switch is fine, but the diode block controls the speeds. It's about a $20 part and located under the dash next to the fan on the passenger side. It's held in with two screws and shouldn't take you more than 20 minutes to replace.

Aug 25, 2010 | 1996 Nissan 200SX

2 Answers

Fuel Pump for 1998 200sx


the fuel pump in in the fuel tank.

Feb 13, 2009 | 1998 Nissan 200SX

1 Answer

Where is ccoling temp sender 1.6 96 nissan 200sx


This is for the 2 litre SR20DET engine so not sure if that's what you have - never heard of a 1.6 version. Below is the exploded diagram and a test for the sensor.

96fe380.jpg

8d1e360.jpg


Oct 20, 2008 | 1996 Nissan 200SX

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

204 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...