Question about 2000 Oldsmobile Alero

Open Question

Push rod order 2000 alero - 2000 Oldsmobile Alero

Posted by on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 400 Answers

SOURCE: what order does the push rods go in a 2000 pontiac

I will assume you are workig on a 3.1 or 3.4 V6 engine?
If so shorts go to intake and long is exhaust. If you look at the rocker arms you will see that the exhaust rockers are placed a little higher than the intake.

Posted on Oct 23, 2009

  • 4 Answers

SOURCE: how do you replace the outer tie rods on 2000 oldsmobile alero

Jack up vehicle; back off set nut that connects outer to inner tie rod; remove cotter pin and castle nut from outer ball socket of t/r end; take a 'pickle fork' and tap between joint and steering knuckle to separate; then unscrew the outer t/r from the inner t/r, "counting the number of turns until completely off. Run the new locking nut onto new tir rod end; turn t/r same number of turns, and lock set nut; runt the new post of t/r end back into steering knuckle, tap down with a hammer, and use new castle nut to tighten; insert new cotter pin and grease fitting; again tighted locking nut to inner t/r; grease new t/r end...good to go!

Posted on Jan 31, 2009

  • 20 Answers

SOURCE: what order do push rods go in 3.4l

If they are the same length no order.

Posted on Aug 03, 2010

  • 14036 Answers

SOURCE: order for push rods 2000 olds 3400 engine

WHEN ORDER PUSH RODS YOUR INTAKE PUSH RODS LENGH 5 3/4 INCHES , THE EXHAUST PUSH RODS LENGTH 6 INCHES. YOU NEED 8 INTAKE PUSH RODS YOU NEED 8 EXHAUST PUSH RODS. YOU CAN GO TO DEALERSHIP BUY OR AUTO PARTS STORES HAVE THEM.

Posted on Sep 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have removes the pushrods from the car and they are different lenths and do not know which sizegoes where


Push rods need to be placed in the same hole they came out of. Your best bet is to take it to a professional mechanic to make sure the engine is reassembled properly.

Mar 06, 2011 | 2000 Oldsmobile Alero

1 Answer

How do i connect the clutch back to the rod


YOU HAVE TO PUSH THE PLASTIC CLIP BACK IN PLACE TO THE CLUTCH MASTER CYLINDER PUSH ROD.

Jan 15, 2011 | 1999 Oldsmobile Alero

2 Answers

3400 sfi 2000 alero firing order diagram


firing order is 1-2-3-4-5-6. Thanks for using FixYa.

jturcotte_610.gif

Dec 24, 2010 | 2000 Oldsmobile Alero

1 Answer

What oder do the rods go back in long short short long


INTAKE TAKE PUSH RODS SHORT ONES THE EXHAUST PUSH RODS LONG ONES

Dec 09, 2010 | 1999 Oldsmobile Alero

2 Answers

I have a 1999 olds alero, in which i just replaced all the gaskets and the front cylinder head. no more white smoke, but now it is backfiring and it wont stay running (low rpm). i had a code for a faulty...


hi this sounds like you have the firing order incorrect..have you tried changing the firing order? the firing order is, 1,2,3,4,5,6 and also check to see if you have left any vacuum hoses of as this will also give you the same problem ....hope this helps

Oct 10, 2010 | 1999 Oldsmobile Alero

1 Answer

Order for push rods 2000 olds 3400 engine


WHEN ORDER PUSH RODS YOUR INTAKE PUSH RODS LENGH 5 3/4 INCHES , THE EXHAUST PUSH RODS LENGTH 6 INCHES. YOU NEED 8 INTAKE PUSH RODS YOU NEED 8 EXHAUST PUSH RODS. YOU CAN GO TO DEALERSHIP BUY OR AUTO PARTS STORES HAVE THEM.

Sep 10, 2010 | 1999 Oldsmobile Alero

1 Answer

2000 olds alero v6 spark plug firing order diagram


2000 Oldsmobile Alero 3.4 liter V-6 VIN "E"

488b39c.gif


Hope helps (remember rated this).

Jul 05, 2010 | 2000 Oldsmobile Alero

1 Answer

How do you replace the outer tie rods on 2000 oldsmobile alero


Jack up vehicle; back off set nut that connects outer to inner tie rod; remove cotter pin and castle nut from outer ball socket of t/r end; take a 'pickle fork' and tap between joint and steering knuckle to separate; then unscrew the outer t/r from the inner t/r, "counting the number of turns until completely off. Run the new locking nut onto new tir rod end; turn t/r same number of turns, and lock set nut; runt the new post of t/r end back into steering knuckle, tap down with a hammer, and use new castle nut to tighten; insert new cotter pin and grease fitting; again tighted locking nut to inner t/r; grease new t/r end...good to go!

Jan 31, 2009 | 2000 Oldsmobile Alero

Not finding what you are looking for?
2000 Oldsmobile Alero Logo

Related Topics:

149 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...