Question about Hyundai Entourage

Open Question

How do I install roof rack cross rails on my 2007 hyundai entourage?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 840 Answers

SOURCE: Luggage rack cross rail installation

They have torx screw or allen wrench's they just unbolt look at the top and then look on the sides of these extensions as soon as you get them loose you should be able to pull them out/Please rate my response thank you very much

Posted on Jan 31, 2009

  • 1 Answer

SOURCE: Re-positioning crossbars on roof rack

Hi Its easy to do I did this last night. It is in the manual but light on detail

Remove the rubber and you will see a screw
Use a size 25 torx screw bit and a ratchet as it is in tight. Undo the screw and move the bars.

For some reason there is only one more locking point you can move forward to from there you are on your own but normally it is just the last bit you need.

I believe the logic is to do with a combination of wind noise and the position of the sun roof on some models.

Posted on Jun 30, 2009

gladys_neal
  • 334 Answers

SOURCE: where is the headlamp fuse on a 2007 hyundai

there should be a left and right headlamp fuse in the underhood fuse box the underside of the lid has the location of each fuse, hope that helps

Posted on Dec 10, 2009

Testimonial: "thanks"

  • 1 Answer

SOURCE: I need to remove the luggage racks from my 2007 Hummer h2 SUT

I have the same vehicle and was able to remove mine with the following steps: 1) remove light behind each rear of luggage rack rail using phillips screwdriver (one screw each side). 2) remove molding underneath each light using T20 torx driver (2 screws each side). 3) Loosen cross rails nobs. 4) Side cross rails off of roof.

Posted on Dec 27, 2009

  • 52 Answers

SOURCE: how to replace 2007 hyundai entourage cabin air

cabin filter is typically behind the glove compartment, take the glove compartment out, remove the plastic behind the glove compartment and you should be able to get to the filter

Posted on Mar 12, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I install the cross rails on a 2008 suburban roof rack


but that's all you need to do is remove the end piece on both sides and slide the cross rails in and replace the ends

T-15 is the size...Its a good idea to check them regularly if you use the rack regularly...>
Cross rails retaining screws

Mar 07, 2015 | 2008 Chevrolet Suburban

1 Answer

I purchased a Hyundai 00285-03006 fully enclosed luggage carrier and the instructions are one picture with no words. The picture does not describe where the carrier is in the picture, where the rails fit...


That same luggage carrier is sold (as OEM approved equipment) for MANY different makes and models of automobiles. From what I can see, it simply clamps onto the cross-rails on your luggage rack. (Not much instruction needed) It does require however, that you have a luggage rack and a cross-rail kit. The cross-rail kit is sold separately. I would give you the part number, but the cross-rail kit varies depending on your make, model, and year.


dttech_88.gif


Cross-Rail Kit


dttech_21.jpg

May 22, 2011 | Hyundai Veracruz Cars & Trucks

1 Answer

How are the cross rails on the roof rack adjusted on a 2005 santa fe


YOU SHOULD HAVE A LITTLE BLACK OVAL RECESSED CENTER. THIS GOES OVER THE S LOOKING SYMBOL IN THE UPPER PART OF THE CROSS ARM PUT THE KEY IN THE SLOT AND TURN 1/4 TURN. YOU HAVE TO PUT PRESSURE ON THE KEY AS YOU TURN. NOW LIFT UP ON THE RELEASE AND PUSH DOWN ON THE PART BELOW THE RAIL AT THE SAME TIME. AFTER YOU MOVE THE CROSS PCS. TO ITS LOCATION LIFT UP ON THE BOTTOM AND PUSH DOWN ON THE TOP. DONT TRY IT WITH THE LITTLE KEY.

Aug 27, 2010 | 2005 Hyundai Santa Fe

1 Answer

How do I adjust the cross rails on my 2005 Santa


one person either side, lift up the tabs at each end and slide back/forward.

May 22, 2010 | 2005 Hyundai Santa Fe

1 Answer

I need to remove the luggage racks from my 2007 Hummer h2 SUT


I have the same vehicle and was able to remove mine with the following steps: 1) remove light behind each rear of luggage rack rail using phillips screwdriver (one screw each side). 2) remove molding underneath each light using T20 torx driver (2 screws each side). 3) Loosen cross rails nobs. 4) Side cross rails off of roof.

Nov 27, 2009 | 2007 Hummer H2 SUT

1 Answer

Can't secure the front cross rail forward for bike rack


dear friend-the roof rack on a sante fe can not be moved.should you attempt that you will have constant rattles on your roof.i can surgest.that you modify your bike rack.

Jul 19, 2009 | 2007 Hyundai Santa Fe Limited

1 Answer

2007 Xterra roof rack


i had the same problem with girlfriends delaer told me when wind test and design them there roof racks are on so i was changing the drag causing the noise. when i put the rack back on the noise stopped

May 29, 2009 | 2007 Nissan Xterra Off Road

1 Answer

2007 Hyundai Santa Fe Limited


Hey all,
I was able to get installation instructions for the cross bars from http://www.capitolhyundai.com and from http://dealerfit.com.  Thanks much to these folks for providing a pdf of these instructions free of charge!
Below is the text from the instruction set that worked best for me.  The other instruction set was nearly identical but it had an alternate Step 2 which involved using a small plastic pry bar.  I added that alternate Step below in the instruction step.  Hopefully I'm able to insert the image of each instruction set so that the Figures are visible.  Its actually not that easy getting the rear rail covers off and its pretty easy to crack them.  I'd recommend gently rocking the covers for a couple minutes in order to loosen them up.  Once you get the covers off, the rest of the install is a breeze and can be done in 2 minutes.  If you have questions, go ahead and contact me.  I also took several photos of my install and that might be helpul.  Cheers!
-LePig
-----------------------------------------------------------------------
SANTA FE 2008 PIN U8210-28000 Cross Bar Assembly Installation Procedures
Kit Contents: • (2) Cross Bar Assemblies Required Tools: • Flat Head Screwdriver
INSTALLATION INSTRUCTIONS
1. Carefully unscrew and remove radio antenna. 2. Grasp the rear rail covers with both hands. Squeeze and pull up & inwards (toward the center of the vehicle) to remove covers. Take care not to break off the tabs by lifting the rear section of the cover first (Figure 1). Be careful not to scratch, damage or dent any painted surfaces. DO NOT PRY AGAINST THE VEHICLE BODY, THIS CAN CAUSE DAMAGE TO THE VEHICLE. 2. - Alternate Method - Locate notch in rear of each cover to insert plastic pry bar.  Remove cover by prying up (with tool) and lifting rear at 45 degree angle (Fig 1). Be careful not to scratch, damage or dent any painted surfaces. DO NOT PRY AGAINST THE VEHICLE BODY, THIS CAN CAUSE DAMAGE TO THE VEHICLE. 3. Check assembly clips for damage and dislocation. Replace if necessary. 4. Open the lever on one side of front/rear cross bar. Gently set the cross bar, with the arrows facing forward, into the channel of the side rails (Figure 2). Guide both sides into the track. 5. To adjust cross bars, open lever and place cross bars in desired location. Close lever (Figure 3). Try to move bars forward/back until they lock into place. 6. Reinstall rear covers by holding cover at a 45 degree angle and inserting the front tab into the rear of the roof rack. After aligning, snap cover in place (Figure 4). Be sure that the rubber lip does not interfere with the covers, and that the covers are fully seated. 7. Reinstall the radio antenna. Note: To remove the cross bars, remove the antenna, remove the covers, open lever of cross bar and slide to end of rail. Hold down locking fingers (on both RH/LH rear rail supports) with a flat head screwdriver (Figure 5). This will allow removal of cross bars from the rails.

81e769d.jpg

Jul 02, 2008 | 2007 Hyundai Santa Fe Limited

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

180 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8195 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...