Question about 1994 Ford Bronco

1 Answer

No fire to new starter. new solenoid, fuse ok.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

Could be ignition switch. try holding the key on and slapping the steering wheel at top

Posted on Oct 04, 2010

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

roniecon
  • 6826 Answers

SOURCE: Starter not working

low voltage might causing ,this problem check battery voltage and if it is ok ,replace starter,starter most likely is the couse to burn fusable link

Posted on Jul 06, 2009

alicantecoli
  • 22095 Answers

SOURCE: 2000 audi a4 starter gremlin

your barking up the wrong gum tree witht the starter motor ,you have an electrical supply problem on the battery terminal area with more than one wire connected or a dodgy earth cable from the engine to the chassis .i would be inclined to check and fit another earth cable from a good connection on the engine -(bell housing) and run it back to battery terminal to eliminate all posibilitys .before anything else ,make you own if you have to but only use copper cable .this is my last question for tonight ,have to go pick er indoors up from work now

Posted on Aug 16, 2009

countrybo331
  • 79 Answers

SOURCE: 93 camry has power wont start, thought it was

the fuel pump relay would have nothing to do with the car turning over...did you test the starter before you put it in?and you are sure you have checked all fuses?like the battery fuse igntion fuse ect...

Posted on Mar 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I replaced the starter ,alternator ,main fuse,and new battery ...and I'm not getting any fire from the battery to crank it ....does anyone know what this problem is ??? ////98 ford explorer


Check the starter solenoid and the connections from the battery to ground, battery to fusebox, ignition key switch, neutral or park safety starting switch, solenoid, and solenoid to starter. Make sure you have ignition key switch wires connected to the solenoid - without them - the solenoid can not close to send 12V to the starter.

Nov 02, 2015 | Ford Cars & Trucks

2 Answers

Suzuki forenza wont even fire or turn over! Headlights and radio work fine just wont start and is new battery!


This procedure usually works:
·Check the battery cable connections:
Make sure the positive cable, makes a good connection at the battery and at the starter. Make sure the negative cable makes a good ground connection at the battery and (preferably) at the engine.

·Check the battery the simple way, like this:
Turn on the headlights, then try to start the car.If the headlights do not dim or go out, then the battery is likely ok.

·Check the starter and solenoid:
If the wiring looks ok, then look at the starter solenoid for a good connection, and proper voltage at the starter(10 volts minimum while cranking).
If the starter spins and no crank, the problem is most likely the Solenoid's bendix gear is stuck.
Have someone hit (not too hard) the starter while you try to start the car. This usually works by dislodging a stuck bendix gear.
·Make a simple test of the alternator:
If you can, somehow get the engine running, measure the voltage at the battery. It should be at least 13.6 volts to properly charge the battery.

Dec 12, 2014 | 2004 Suzuki Forenza

1 Answer

1999 isuzu rodeo blow ignition fuse


Check to see if you are using the proper fuse. If so, disconnect the starter solenoid and then try to start the vehicle. If the fuse does not blow, the starter solenoid (entire starter, actually) should be replaced.

Mar 25, 2014 | 1999 Isuzu Rodeo

1 Answer

Ground cable caught on fire


This is probably a grounded starter. You are lucky the fuse panels are intact and it is not melting the fusible link. You may possibly have a bad solenoid or someone put the wrong starter solenoid on the vehicle.
Starter solenoids can look the same outside and be different inside. If this is a new vehicle to you, the wrong solenoid may have been installed.

Jun 18, 2013 | Ford Bronco Cars & Trucks

1 Answer

1984 crown vic with new battery will not start. its getting fire but will not turnover.


check to see if any ignition fuses may have opened...check the starter solenoid(should be on firewall or near battery...you can take a large screwdriver and cross between the two posts on the solenoid to see if the starter turns..if not suspect the starter

Jan 08, 2011 | 1984 Ford Crown Victoria

2 Answers

Our 95 xj6 electronically dead. ignition switch dead? new battery ok. but auto won't crank... We just towed it home haven't done nothing but try to jump it.


Check the voltage at the control terminal on the starter solenoid when you turn the ignition switch to start position. If you don't get anything, it's the ignition switch, a fuse or fusible link in the ignition circuit, or an open cable from the battery to the starter. If you get low or erratic voltage readings, check the battery terminal on the solenoid to see if you have the same readings. If you do, check the battery cable for corrosion or poor connections at each end. If you have full voltage there, the solenoid is bad.

If you get full voltage at the starter motor terminal, then the motor probably has bad brushes or commutator damage.

Nov 18, 2010 | 1995 Jaguar XJ6

1 Answer

1500 Ram wont start, no crank no click nothing. Air cond and dash lights work just fine just wont start. Battery is ok tried to jump, no luck, put in different battery no luck.


First thing is to check is the ignition fuse/relay under the hood for a blown fuse or bad relay. If everything is ok then set parking brake with truck in park/netural and have someone to turn the ignition over to start and at the same time use a test light to check for fire at the starter solenoid. If no fire then the ignition switch or netural switch on transmission is causing the problem. If you do have power to the starter solenoid then the problem would be either the solenoid or the starter drive locked up on the flywheel. Be sure to remove the negative wire from the battery if you need to remove the starter. Hope this will help you.

Jun 02, 2010 | 2008 Dodge Ram 1500 2WD

1 Answer

Starter not working


low voltage might causing ,this problem check battery voltage and if it is ok ,replace starter,starter most likely is the couse to burn fusable link

Jul 05, 2009 | 1992 Chevrolet C1500

Not finding what you are looking for?
1994 Ford Bronco Logo

Related Topics:

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5471 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...