Question about 1991 Mazda MPV

1 Answer

How can I read error codes on a 91 Mazda MPV?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mazda Master
  • 8,215 Answers

Have the car scanned. Many parts stores (autozone, advance, others) offer free scan service.

Posted on Sep 10, 2010

  • peeledpeas Mar 11, 2011

    Is there no way to manually pull codes on a 91 mazda without a code reader?

  • Jeff Turcotte
    Jeff Turcotte Mar 12, 2011

    Yes, you can use the MIL light to flash the codes.

    look here: http://www.troublecodes.net/mazda/91MZDp...

    During the self-test a service code is reported by the malfunction indicator light. It will represent itself as a flash on the CHECK ENGINE or SERVICE ENGINE SOON light on the dash panel. A single digit number of 3 will be reported by 3 flashes. However, if a service code is represented by a 3-digit number such as 111, the code will appear on the MIL light as three flashes, then after a two second pause, the light will flash three times.

    Start the engine and allow it to reach normal operating temperatures.

    Turn the engine off.

    Warm up engine to normal operating temperature and turn ignition "OFF."
    Ground test connector (Green: 1-pin) with a jumper wire.
    NOTE: Test connector is located next to self-diagnostic connector.


    Turn ignition switch "ON."
    If MIL illuminates, goes off, and stays off, no codes are present.
    If MIL illuminates, goes off, and then starts flashing, codes are present.
    Start engine and check for additional codes.
    If any codes are retrieved, refer to Malfunction Code Charts under DIAGNOSTIC CHARTS. Repair as required.
    AFTER-REPAIR PROCEDURE


    Erase ECU malfunction code memory by disconnecting the negative battery cable and depressing the brake pedal for at least five seconds. Reconnect battery cable.
    (connector is by the right side wheel well in the engine compartment) and then turn the ignition switch to the ON position. Service codes will be flashed on the MIL light.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hey my problem 710 ingine code on 2000 mazda mpv


Google the code & read up (OBD PO710) if that is it
I hope you know when you get codes,
that they do not mean you need to replace
a part
Codes only point to the system with the out of
range fault
You need diagnostic manuals to diagnose &
component test,no parts get replaced until they fail
a test.

Jul 30, 2013 | 2000 Mazda MPV

1 Answer

P1627


take it to dealer

Sep 28, 2012 | 2000 Mazda MPV

1 Answer

How do i take the head bolts off of my 91 mazda mpv


would be best if you are going to do the work yourself to get a chilton or a haynes repair manual that covers the entire vehical top to bottom with illistrated pics and step by step and dos anddo nots

Jul 15, 2012 | 1991 Mazda MPV

1 Answer

My 2000 Mazda MPV stereo unit is displaying Err (error) after I got the code wrong 3 times in a row.


try unplugging battery and plugging it back up.....this should reset it

Jul 03, 2011 | 2000 Mazda MPV

1 Answer

I got three error code for my Mazda MPV P1518,P1520,P0306.


P1518- Intake manifold runner control fault- stuck open
p1520-intake manifold runner control fault
p0306-cylinder 6 misfire detected

good luck

May 11, 2011 | 2000 Mazda MPV

1 Answer

My 91 mazda mpv 4x4 van won't start. we were


than I would have the fuel pressure check and change the fuel filter

Mar 09, 2010 | 1991 Mazda MPV

1 Answer

96 mazda mpv minivan 165k mi. Ran fine until one day just died.Had towed home.3 mech.tried diagnose gave up wouldn't start-turns over-no start. Last mech.replaced timing belt&idle pulley. Still no...


I was browsing unsolved problems. If you still have the problem, I'll try to help you. But it's going to be awhile trying to communicate back and forth. First...Check the engine for spark. Take off a plug wire and stick a screw driver in the wire end and place the metal part of the screw driver next to something on the van that's metal. Have someone crank it over for just a second or two and see if a small spark jumps from the screw driver to the metal part. I'll check back for your answer.

Mar 05, 2010 | 1996 Mazda MPV

2 Answers

P2179 code from


P2179 System Too Lean Off Idle .Have read post where people have been getting this code after installing a aftermarket intake.

Jan 29, 2010 | 2005 Mazda MPV

1 Answer

2001 Mazda MPV Error code p0431 makes engine light come on


THAT CODE IS FOR THE BANK 2 OR FRONT CATALITIC CONVERTER ON THE VAN. YOU CAN HAVE THE DEALER REPLACE IT OR A MUFFLER SHOP CAN DO IT. THE CAT IS A PART OF THE FRONT EXHAUST MANIFOLD AND WILL NOT BE CHEEP TO REPLACE.

Jun 27, 2009 | 2001 Mazda MPV

1 Answer

Where is the power steering resorvoir on a mazda mpv 1999


If this is the same as my 91 (No MPVs Show for 99) the power steering is located on the passenger side behind the alternator and its a pain to get to if you dont know where it is. Make sure you have it outside in the sun and you will see the filler dipstick. That is where the resovoir is located. Its actually right at the power steering pump location if its like my 91.

If its like the 2000 (or so) its an actual seperate resovoir on the passenger side fenderwell. Its in an obvious place so it you cant find it Im guessing your engine is inline and rear wheel drive like my older MPV and youll find it behind that alternator.

Hope this helps and lf it does dont forget to rate the solution.

Mar 22, 2009 | 1999 Mazda MPV

Not finding what you are looking for?
1991 Mazda MPV Logo

Related Topics:

413 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8211 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...