Question about 2006 Pontiac G6

1 Answer

How much torque is needed on the axle nut when replacing the front wheel assembly of a 2006 pontiac g6 ?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 175 Answers

The drive-axle/hub nut is supposed to be 159 ft-lbs, but know that you are required to use a NEW nut.

Posted on Mar 23, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Axle nut torque


Front Propeller Shaft Retaining Nut
181 N·m
134 lb ft

Jan 27, 2017 | 2006 Pontiac Vibe

1 Answer

Front wheel bearing torque


Better late than never Brucy....CLICK HERE TO SEE YOUR WHEEL BEARING GUIDE. Repair Guides Front Suspension Wheel Bearings AutoZone com

Apr 02, 2014 | 2006 Pontiac Grand Prix

1 Answer

Front wheel bearing torque


The axle nut is 118 ft lbs
The other 3 bolts are a 75 ft lbs

Apr 02, 2014 | 2006 Pontiac Grand Prix

1 Answer

How do I rgerplabe how do I replace a front wheel bearing?


TO REMOVE FRONT WHEEL BEARING.YOU NEED TO SAFELY RAISE SUPPORT VECHICLE ON JACK STANDS.MAKE SURE SITTING ON LEVEL SOLID GROUND.BEFORE RAISING VECHICLE OFF GROUND YOU NEED TO LOOSEN HALF SHAFT AXLE NUT JUST A LITTLE BECAUSE WHEEL IN THE AIR HARD TO LOOSEN AXLE NUT WHEN YOU HAVE HOLD THE WHEEL WHILE LOOSEN THE AXLE NUT WHICH IS TORQUE ON ABOUT 200 FT LBS.USING A SIX POINT AXLE SOCKET SOCKET SIZE COULD BE 34 OR 35 METRIC 1/2 INCH SOCKET.YOU NEED 1/2 INCH BREAKER BAR.ONCE YOU LOOSEN AXLE NUT A LITTLE THEN RAISE VECHICLE THEN REMOVE WHEEL.THEN FINISHING REMOVING AXLE NUT AND WASHER.THEN REMOVE THE CALIPER FROM THE STEERING KNUCKLE AND SUPPORT IT ASIDE USING A PIECE OF WIRE.REMOVE BRAKE ROTOR.THEN REMOVE THE 3 HUB BEARING ASSEMBLY BOLTS. USE A SWIVEL SOCKET GOING TO BE HARD TO REACH SPOT WITH A REGULAR SOCKET. REMOVE THE HALF SHAFT FROM THE HUB BEARING ASSEMBLY.REMOVE HUB AND BEARING ASSEMBLY. PUT EVERY THING BACK VISA VERSA. TORQUE HUB BEARING BOLTS TO 70 FT LBS. TORQUE AXLE NUT 284 FT LBS IF YOUR CAR IS 1998 MODEL AND TORQUE AXLE NUT 100 FT LBS FOR THE 1999 TO 2001 MODELS.THE WHEEL HAS TO BE ON THE GROUND JUST ENOUGH TO KEEP IT FROM TURNING.DONT LET ALL THE CAR WEIGHT DOWN UNTIL YOU HAVE TORQUE WHEEL TO THE RIGHT TORQUE.LET ME KNOW IF YOU HAVE ANY PROBLEMS.

Mar 21, 2011 | 1999 Oldsmobile Alero

2 Answers

I have replaced the stabilizer links on my 2008 Pontiac G6 base model and I cant find the torque specs for the nuts.


Thanks for using FixYa.


Stabilizer Links

Removal & Installation

  1. Raise and support the vehicle.
  2. Remove the front tire and wheel assembly.
  3. Disconnect the stabilizer link from the stabilizer shaft.
  4. Disconnect the stabilizer link from the strut assembly and remove from the vehicle.

To install:
  1. Connect the stabilizer link to the strut assembly.
  2. Tighten the stabilizer link nut to 48 ft. lbs. (65 Nm).
  3. Connect the stabilizer link to the stabilizer shaft.
  4. Tighten the stabilizer link nut to 48 ft. lbs. (65 Nm).
  5. Install the front tire and wheel assembly.
  6. Lower the vehicle.

Mar 04, 2011 | Pontiac G6 Cars & Trucks

1 Answer

What is the torque spec for the front wheel bearing on a 2005 Pontiac 6


I come up with 96lbs for the three bolts that hold the bearing assy. and 118lbs on the axle nut. Use locktite on the axle nut.

Jan 23, 2011 | 2006 Pontiac G6

2 Answers

Replacing passenger side front wheel bearing on Pontiac G6 2006. Have all 3 bolts out and wheel nut off, seperated old hub assembly from strut tower, but won`t slide off splined shaft?????


use a hammer to tap on the head of the shaft to push it back out, put a small block of wood on it before hitting it so you dont mushroom the end or distort the threads.

Good luck!!

Mar 21, 2010 | 2006 Pontiac G6

1 Answer

How install halfshaft axle on a ponitac g6


Do you have them off already? If not jack car block up at FRAME put in neutral pull wheel remove tie rod nut remove axle nut remove ball joint bolt from lower knuckle seperate knock axle out from knuckle don't DAMAGE axle threads pop axle out from trans large prybar from axle to trans should pop out held in with snap ring install reverse or what you did

Oct 09, 2009 | 2006 Pontiac G6

1 Answer

How do i change the front driver wheel bearing on my 06 g6 gt. anti-lock brake system


remove wheel brahes and rotoe then remove axle nut and there are 3 bolts holding bearing to car remove these unplug wiring to bearing tap with hammer til bearing is off reinstall bearing in reverse order

Jul 21, 2009 | 2006 Pontiac G6

Not finding what you are looking for?
2006 Pontiac G6 Logo

Related Topics:

1,068 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8743 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...