Question about 1994 Honda Accord

1 Answer

My clutch pedal is extremely soft, and has started to stay on the floor. Is there something that I can do to rectify the situation until I can get it to my mechanic? Help!

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Honda uses hydrolic clutches. Pop the hood and there should be a reservoir of "clutch fluid" (clutch systems use brake fluid) next to the brake fluid reservoir. It will be marked DOT 3 just fill that up with brake fluid and you'll be good to go.

Posted on Sep 10, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Clutch pedal went to the floor no return


slave cylinder failure
replace both the clutch master cylinder and slave cylinder and bleed out properly

May 27, 2017 | Cars & Trucks

1 Answer

Manual. Clutch pedal very soft. Sometimes pedal stays down. Unable to change gears until engine stalls or is turned off. Worse in very cold weather. Fluid level OK.


the master cylinder that operates both the clutch and brakes is either bad or needs bled,or could be leak in either brakes or clutch slave cylinder

Mar 10, 2016 | 2013 Hyundai Accent

1 Answer

My vehicle will not move when I put it in gear


Are you sure that your gears are actually engaging. Do you feel resistance (however slight) when you select a gear including reverse gear. If it is a manual gearbox, then either the gears are not actually being selected and that could be something like a broken linkage or the clutch is not releasing when you let your foot off the pedal. The clutch problem could be rectified by adjusting the cable, if fitted, or the actuating mechanism is stuck in and not releasing the clutch. Does the pedal feel soft or in an unusual position.
It will be a dirty job to find and rectify the problem so may well be best left to a mechanic.

Feb 21, 2016 | Cars & Trucks

1 Answer

The clutch pedal wants to stay on the floor


Replace the clutch master cylinder and clutch slave cylinder as you have a failure in the system allowing air in and that is why the pedal goes to the floor and will not return up. May be a proper bleed of the system first may fix the problem so do that first but if the fault comes back after a few days then it will be dollars time.

Jan 10, 2014 | 1998 Chevrolet Cavalier

1 Answer

1996 nissan maxima clutch squeals pedal stuck to floor


Sound like you're going to need a whole new clutch assembly, but if the fluid level was dry you may have sucked air into the system which means that the clutch will have to be bled at the slave cylinder, just like you would brakes. The squealing sound is coming from the throw out bearing, usually when the do that it means that the bearing is frozen and cannot spin. Either way it looks like you'll be dropping the transmission to work on the clutch.

Jan 30, 2013 | 1996 Nissan Maxima

1 Answer

Clutch pedal goes to floor and half works on my b2200 1987 mazda pick-up


If the clutch is hydraulic operated, you need to bleed the clutch at the slave cylinder, down on the transmission housing. Bleed it just like you bleed brakes of air in the line-open bleeder valve, someone pushes clutch pedal slowly to floor, close valve, and repeat until fluid comes out valve in a steady stream. Make sure the clutch reservoir is full before starting. It uses regular brake fluid.
If not hydraulic, it would be cable operated. Adjust the cable until clutch pedal is right.

Dec 29, 2012 | Cars & Trucks

1 Answer

Clutch pedal straight to floor


If you put the trans in neutral and depress the clutch pedal it should still start.
The clutch is hydraulic, so there should be something connecting the pedal to the master cyl and the slave cyl to the clutch disk.

Jun 26, 2012 | 1991 Honda Accord

2 Answers

Clutch pedal went to the floor but did not come back up. Heard something 'pop' when pushing in clutch last night. Got home, then tried to start car this morning and clutch made a 'pop' sound again when...


there is a plastic clip that connects the clutch pedal to the rod that goes to the master cylinder, chances are that it let go. Bad thing is that it is only available from GM along with the rod. It is around 50

Oct 16, 2009 | 2003 Oldsmobile Alero

1 Answer

1996 nissan maxima clutch sticks to floor


yes, Briong the pedal up where it belongs, then open an fill your master cylider. Then go below and open the bleeder intil the fluid runs/drips steady and free of any bubbles. Do not pump the pedal. When only fluid comes out, tighten/close the bleeder and give it a try. Good Luck. If peal dives again, replace the master cylinder.

Jul 02, 2009 | 1996 Nissan Maxima

Not finding what you are looking for?
1994 Honda Accord Logo

368 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...