Question about 2002 Nissan Quest

Open Question

When the brakes are applied, the Emergency Brake light comes on towards the end of the braking. It doesn't happen everytime, but most. I tried reseting the Emergency brake and the fluid level is correct. The brakes are not squealing either. Thanks.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1056 Answers

SOURCE: Brake lights not working when you apply brakes

check the brake light switch.
It's usually up under the dash, and it activated by the brake pedal.

There are 2 wires going to it. To test it, jumper across the leads.
or, watch the "action" sometimes you just need to reposition the switch to get it to work.

Posted on Aug 07, 2008

  • 1 Answer

SOURCE: brake lights stay on all of the time, ABS light on when driving

You most likely need to replace your brake switch, which is a
a $8 part. If you look up along the brake peddle you will see it depressing a switch. on the end of that switch is a electrical connector that you can press on one side to remove.
Once removed your brake lights will be disconected and your ABS
light should go off. You then need to replace the switch that it pluged in to.

Posted on Apr 12, 2009

  • 383 Answers

SOURCE: Brake lights stay on when lights are on

randyref: The most common problem with the Nissan's when it came to brake lights staying on, was a little plastic stopper button
which is located up near the top of the brake pedal arm.
If you follow the brake pedal arm up, you will find the brake light switch. If you push the pedal down, feel where the brake light switch is suppose to contact the pedal frame.
You will probably discover that there is a hole there instead of something that the switch was to come in contact with so it could be compressed which in turn, opened the circuit causing the brake lights to go out.
The part is available from Nissan and usually is stocked because it is a common problem. I stock 3-4 in my shop and I'm not a dealer.
The part it self is a round semi soft clear plastic disc with a small button which you push through the hole in the pedal frame, where it snaps in place.
I'm willing to bet that this will solve your problem. Check it and get back to me.

Posted on Apr 20, 2009

  • 1 Answer

SOURCE: I have 2007 Altima Brake Light problem

I had the exact same issue, brake fluid level was a "hair" low, I added a few drops and the brake light has not come on since

Posted on Jun 07, 2009

  • 3600 Answers

SOURCE: ABS and emergency brake light on

try bleeding the system and if you went 4x4ing you may have knocked off a wheel sensor.

Posted on Jun 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Emergency brake stuck to floor will not release


Hi Barbara:
I'm guessing that when you pull the release handle it moves, but nothing happens.
Odds are that whay has happened is that the cable has come out of the release lever, Or, the cable sheath has slipped out of its retaining slot.
Either way, you have two things to do:
1) Get mobile so you can go home. To do this, put it in park or low gear with the motor off. You will need to access under the dash where the release mechanism is located. Use a pair of pliers (or whatever else will work) to pull or pry the release lever away from the firewall (towards the seat. The parking brake will release.
2) Go home (or wherever, just don't use the parking brake.
3) Repair the brake:
- Release the Cable Sheath from the retaining slot.
- connect the cable to the release lever
- Re-install the cable sheath into the slot.
Ta Da!!!!

Mar 26, 2016 | 2004 Nissan Quest

1 Answer

VW golf mk4 press brake warning light not coming on


What brake are you talking about? The emergency brake or the brake pedal. Warning lights only come on when 1, there is a leak ing the system while driving and you loose pressure, 2. upon starting the vehicle as a bulb check, 3. When you apply the emergency brake. Have the brake switch on the pedal and emergency brake checked also check the bulb. If the bulb lit upon startup, it is probably the switch. Please give more details so that we can be better able to help you.

Dec 10, 2014 | Cars & Trucks

1 Answer

Steady brake light on dash


i wonder if you mean abs light i f so loosen and re tighten .often no contact makes the abs light come on .other wise release emergency brake perhaps the peddle got pushes a couple of clicks enough to make light come on but not enough to look like it is applied.try emergency brake first push then release with handle.you wouldnt beleive how many people this happenes to .

Jan 19, 2013 | 2001 Chevrolet Silverado 2500

1 Answer

I have a 1999 Jeep Grand Cherokee, the brake light is staying on when vehicle is in park...why?


are we talking about the rear tail brake lights or the light on the dash. if dash light possible emergency brake slightly applied or low brake pressure in brake system or low brake fluid in reservoir. Rear brake lights ? check the brake switch under dash as it may have come mis adjusted for proper on/off activation

Apr 11, 2011 | Jeep Cherokee Cars & Trucks

1 Answer

My emergency brake light has come on and stays on along with the little circle that looks like there is water or something on it in the message display...they both come on at the same time when starting...


I'd probably safely raise and support the rear of vehicle, make sure rear wheels turn freely, no braking action unless brakes are applied. You could raise one wheel at a time.
Check the emergency brake release mechanism, the switch and wiring circuit?
My main concern is your not driving down the road with braking action ongoing w/o brakes being applied.
My ex drove 50 miles one time with e-brake not fully released, the brakes were smoking like crazy when she got home. Glad she got home ok. I'm glad it didn't catch fire.

May 10, 2017 | 2004 Chevrolet Venture Passanger

1 Answer

My emergency break light wont come on and i have an convertible and it wont the top come down unless emergency break light is on and e brake does come up and idk


there should be a micro-switch that works when the emergency brake is applied, it should be located by/near the brake. Hope this helped Tim

Nov 07, 2010 | 2000 Porsche Boxster

2 Answers

1997 Jeep wrangler rear emergency brake cable replaced and now brake light stays on


possible cable out of adjustment to loose.try forcing brake aplicator towards full off and see if it goes off. if so adjust switch or cable

Jun 26, 2010 | 1997 Jeep Wrangler

1 Answer

Adjusting the parking brake on 03 pontiac vibe


If you look under the van on the driver side (usually) you'll see where the two cables from the rear inter-connect with the main cord to the front. Here, you should find an adjustable bolt that you can tighten. If it is not here, it may need to be tightened from there rear tires.

If you have drum brakes in the rear, these are most likely "self-adjusting" brakes, which may interact with the emergency brake. Everytime you back up, and apply the brakes, you are activating the self adjuster (you would have seen this located at the bottom of the brake system between the two brake pads. This is the self adjuster. Try going in reverse at about 5 miles per hour, and hitting the brakes firmly (not slamming on them). Drive forward again, and firmly press the brakes. Go in reverse again, and apply brakes firmly again; (do this about 4 or 5 times to get the rear brakes adjusted). Try the emergency brake again and if still not tighter, purchase or look in your repair manual as to how to adjust the emergency brake.

Please let me know if you need further assistance.

carsandcomps,

Guru, Premium Expert @ Fixya.com

May 29, 2010 | 2003 Pontiac Vibe

2 Answers

Rear driver wheel locks up and abs light comes on


you may have a bad ABS module but you may need further diagnostics to confirm this

Apr 25, 2010 | 2000 Pontiac Montana

2 Answers

Rear brake lights do not work.


The brake light that is on the dash is for the emergency brake...When that light is on that is supposed to tell you that the emergency brake is applied if the brake is not applied then you need to service the emergency brake. And on the brake pedal there is a coupler that is hooked up to the pedal bracket that wire may be soft set try gently snapping it into place.

May 10, 2009 | 1995 Honda Civic del sol

Not finding what you are looking for?
2002 Nissan Quest Logo

Related Topics:

81 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...