Question about Hyundai Accent

1 Answer

How can i bleed the slave cylinder on my 1998 hundai accent? the clutch still works, but i have to push it all the way to the floor

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Hyundai Master
  • 8,180 Answers

If you have air in your system, the slave is probably leaking. Did you replace the slave? After replacing the slave, you can bleed it by opening and closing the bleeder port while another person holds the clutch pedal down eack time to you open the bleeder. If you have more questions, please reply.

Posted on Sep 10, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to bleed the clutch on a 2002 hyundai accent


its the same process as bleeding brakes- except you pump the clutch pedal and loosen the clutch slave cylinder located by the front motor mount instead of a brake slave cylinder.

what i do is just loosen the slave cylinder bleeder screw and let it all run dry. then disconnect the reservoir from the master cylinder and clean it out with brake cleaner because all that black junk rests in the bottom of that. theres still more in the line, so reattach the reservoir and fill it up. let it bleed all the way back down the line and proceed to pump and bleed the system. if you know how to bleed brakes it should be a piece of cake.

Aug 13, 2016 | 2002 Hyundai Accent

1 Answer

My 94 hyndai accent wagon clutch goes to the floor with no resistance. I topped off the fluid on the master cylinder, it was bone dry. Fluid is hooding but it still has the same problem with the clut


Lol, you need to bleed the master cyl. first, then remove the pipe on top of slave, and bleed it till it spits out. eventually the clutch will be restored. I suggest you fit new master and slave kit first.

Jul 20, 2014 | Hyundai Accent Cars & Trucks

1 Answer

How do i bleed the clutch on a 2001 Mitsubishi challenger


1 Press clutch pedal in fully and hold.
2 Open the bleed screw to allow fluid to escape.
3 Close bleed screw quickly.
4 Release pedal completely
5 Top off fluid in reservoir. Leave cap off of reservoir.
6 Repeat steps 1 to 4 no less than 10 times before going to 7 below. NO PUMPING!
7 Now purge the slave cylinder of any air bubbles that might be trapped inside of it.
8 Grab the clutch fork and push towards the slave cylinder pushing the rod all of the way into the slave cylinder as far as it will go AND HOLD it in.
9 open bleed valve and command helper to push the clutch down slowly purging any air that was trapped in the slave cylinder
10 As soon as the pedal hits the floor command your bleeder monkey to close the valve before you let the pedal return from the floor.
11 Repeat steps 1 to 4 one last time and proceed to the clutch reality check.

Jun 21, 2014 | 2001 Mitsubishi Montero

1 Answer

How do i bleed the clutch fulid


1. Inspect and fill clutch master cylinder reservoir with appropriate hydraulic oil. You will want to check this during the bleeding process making sure it doesn't run out or you will get air into the system again. Leave cap off of reservoir.
2. Have your friend camp in the drivers seat to push in and let out the clutch pedal when you tell him to.
3. During this procedure DO NOT allow your friend to "pump" the clutch pedal.
4. You will be opening and closing the bleed screw on the slave cylinder as instructed below. CAUTION: During this procedure protect your eyes from squirting brake fluid by using a small hose and a soda bottle. Brake fluid is nasty stuff so wear gloves.
5. (Helper) Press clutch pedal in fully and hold.
6. (You) Open the bleed screw to allow fluid to escape.
7. (You) Close bleed screw quickly.
8. (Helper) Release pedal completely
9. (You) Top off fluid in reservoir. Leave cap off of reservoir.
10. Repeat steps #6 - #9 no less than 10 times before going to #12 below. NO PUMPING!
11. Now you will want to purge the slave cylinder of any air bubbles that might be trapped inside of it.
12. Grab the clutch fork and push towards the slave cylinder pushing the rod all of the way into the slave cylinder as far as it will go AND HOLD it in.
13. (You) open bleed valve and command helper to push the clutch down slowly purging any air that was trapped in the slave cylinder
14. (Helper) As soon as the pedal hits the floor command your bleeder monkey to close the valve before you let the pedal return from the floor.
15. Repeat steps #6 - #9 one last time

Dec 03, 2013 | 2001 Chevrolet Silverado 1500

2 Answers

Clutch suddenly has no resistance and car won't shift gears. Fluids were low, have put fluid in the reservoir but still doesn't work. How do you bleed a clutch line?


on the transmission there is a slave cylinder that works like a brake cylinder, when you apply pressure to the clutch pedal a rod inside the vehicle under the dash pushes into a clutch master cylinder, (almost like a brake master cylinder without the reservoir, as the clutch master cylinder works off the brake master cylinders reservoir) the plunger in the clutch master cylinder applies fluid pressure to the slave cylinder,(located down on the trans near the clutch fork assembly) which projects a piston rod into the clutch fork dis-engaging the clutch. To bleed the clutch slave cylinder locate the bleeder screw on the slave cylinder,break loose so it loosens and tightens easily. Check fluid in brake master cylinder reservoir,fill if needed, while bleeder on the slave cyl is closed have a helper push clutch pedal to floor and back 7-8 times, (At first the clutch might stay at the floor, just pull it up by hand or foot and continue) after several pumps with no rest time push pedal to the floor and hold down with foot pressure, at this time loosen the bleeder on slave untill fluid leaks out, watch for air bubbles, close bleeder and repeat untill there is no sign of air bubbles, (make sure to check fluid in the brake master cylinder and keep fill as needed, do not let fluid get less than 1/2 empty as it might **** air and you will have to start over) If this does not bring clutch to operate then you need to check if slave cylinder is reachig its full extension of push rod or not. If it is not then you will have to replace the clutch master cyl or the clutch slave cyl or both as seals are bad and wont hold pressure. Or you need to inspect the clutch fork,the throw-out bearing, or the pressure plate fingers and clutch plate for failure or broken bent parts. I hope it turns out to be a easy fix on that clutching thing.

Jan 14, 2011 | 1995 Nissan Pickup

1 Answer

Can't get clutch to bleed on 1996 s 10 we have bleed bleed and bleed


Hi if you have done the following to bleed the clutch.
1 open bleed screw
2 push pedal to floor and keep on floor
3 do bleed screw up
4 lift pedal
5 undo bleed screw
6 push pedal to floor
7 do bleed screw up
8 lift pedal up
you need to repeat this a few times but making sure the fluid level dont drop below the lowest level else you will get air in the system.

right now if you have done the above properly and you still either get the pedal going to the floor and staying their or you have no pedal at all then this points to their being a fault with either the clutch master cylinder or clutch slave cylinder, now in most cases the one that fails is the master cylinder this is the one that is connected to the clutch pedal now its usually this one that fails and causes the pedal to go to the floor or have no clutch.

but it could also be the slave so bare this in mind, if the pedal comes back up after pushing it down then the chances are its the slave at fault and this is the one on the gearbox that operates the clutch arm.

let me know how you get on or if you need further assistance ok

plz rate this solution as i have a whole page of unrated posts, thanks

Dec 01, 2010 | Chevrolet S 10 Cars & Trucks

1 Answer

The pedal of my clutch is reaching the floor is that a big problem?


sounds like it could become a problem...
What I would do if it were my vehicle that the clutch pedel was saging to the floor ... I would check the clutch master cylinder for fluid ...
Then I would fill it back up and bleed the slave cylinder ....

Oct 06, 2010 | 1999 Hyundai Accent

3 Answers

1998 Hyundai Accent clutch pedal travel


dear friend-you can bleed the clutch.im am sure this will solve you problem

Jun 30, 2009 | Hyundai Motor 1998 Accent

1 Answer

1997 hyandai accent gt clutch problem


hi considering age of car and that you have no leaks on hydraulics? may i suggest you try bleeding the clutch to rid of old fluid a couple of pumps may be suffice ? b/fluid does absorb moisture and heat over time hence recommendation tat fluid be changed at period specified in handbooks ie 12 monthly ?

May 15, 2009 | 1994 Hyundai Excel

1 Answer

2000 cavalier clutch pedle goes to floor when pushed and stays there, clutch not working no pressure


You are going to have to replace the master and slave cylinders for the hydraulic clutch, the seals have failed in the slave, but from past experience they should always been replaced as a pair.

Oct 12, 2008 | 1998 Chevrolet Cavalier

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

125 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...