Question about 2005 Buick LaCrosse

1 Answer

Need to remove driver side window switch assembly

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 4,102 Answers

Hi, if your going on about the buttons you press to raise and lower the window then all you need to do is get a flat bladed screwdriver and get this under the edge and lever it up, its only pushed into place so it will just pull out then unclip the wires and you can then remove the clip from the car.

let me know if you have any problems ok

Posted on Sep 10, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove the driver side door panel on a 1994 Lincoln Mark VIII


Remove mirror mount cover assembly.
Remove inside door handle cup (22634).
Remove door lock control bezel.
Remove window control bezel.
Remove interior lamp lens.
Remove screw from interior lamp assembly body.
Remove screw from window control bezel opening.
Disconnect mirror, lock switches and memory seat on driver side from bezels and wire harness.
Disconnect window switches from window bezel and wire harness.
Lift front door trim panel (23942) vertically, out of weatherstrip and over lock rod.
Disconnect interior lamp (13776) from wire harness.
Remove front and rear door trim retention hooks into door inner panel.
To install, reverse Removal procedure, paying special attention when inserting inner door trim into weatherstrip. Rock inner door trim into weatherstrip and push downward until lower trim belt character ditch lines up with score mark on inner door panel.

Aug 16, 2014 | 1994 Lincoln Mark VIII

1 Answer

Remove and replace drivers side power window switch


I am assuming its the drivers door window you are speaking of....
The drivers door has the master window switch w/lockout. The entire assembly must be replaced. The individual switches on the drivers door can't be replaced by themselves. Some GM vehicles allow the panel with the switch assembly to be removed without removing the door panel. However, most require the door panel to be removed for access to the window switch assembly. The master door/window switch assembly is not cheap, by the way.
I would check/replace the window relay first. Usually located under the dash, or under one of the seats.
Might just be the window motor on the problem window.

Jul 08, 2013 | 2001 Cadillac Eldorado

1 Answer

Electric windows dont move up or down on my honda accord


If the windows don't work, any of several issues is likely to blame, including no electricity, bad switches, bad motor, damaged window regulator, or even a broken wire.

Automotive power windows use a switched motor to operate a mechanical window regulator. This regulator moves the pane of glass into the door.

To check and confirm the fault try this procedure:--

1) Open the fuse panel and check the fuses for disrupted elements. The fuse panel at the driver's side kick panel, or between the dashboard and the door. In some cars the fuses are mounted in the engine compartment, in front of the driver's side firewall. Check the fuses and replace if faulty.
2)
Test the wiring harnesses from the fuse panel to the switches and from the switches to the window regulator motor. If the circuits test fine, then proceed to the next step. If a wiring harness is shorted or damaged, it will need to be replaced.3) Remove and test the switches on the driver's side door panel. Pry them up with a screwdriver and pull them free of the panel's opening. Disconnect the switch assembly from the wiring harness by pulling the adapter plug from the assembly. Test the switches individually by touching both sides of one switch with the circuit tester. Each switch will have two terminals, and if the tester is positive on both terminals while the window is activated, then the switch is good. Replace the switch assembly if any of the switches fails the test. Most power window switches come in assembled modules and cannot be replaced individually.4) Remove and test (if possible) the power window motor. Turn the armrest bolts and interior door handle screws counterclockwise, then pull the door panel free from the pop rivets. Behind the panel are a window regulator, the window glass, and the electric driver motor. The motor is usually located in the lower right section of the door. Unplug the motor from the wiring harness and unbolt it from the window regulator by turning the bolts counterclockwise. Pull the motor straight out, away from the gears. And check out if motor is receiving exact 12 volts at the terminals. If not then either motor is faulty or there is a confirm short if motor is replaced.

5) If all the above mentioned possibilities are checked out ok then the window regulator needs to be checked. Inspect the window regulator's joints for rust or stiff movement, if the electrical system is operating correctly. These joints can corrode or break, causing the window to stop working. With the door panel off, the window regulator can be removed and replaced by sliding the glass away from the track mounts, then turning all mount bolts counterclockwise and manipulating the regulator out of the door.

Thanks. keep updated for any more query.you can rate this solution and show your appreciation.

Sep 16, 2010 | Honda Accord Cars & Trucks

1 Answer

Rear wiper and window does not work


If the windows don't work, any of several issues is likely to blame, including no electricity, bad switches, bad motor, damaged window regulator, or even a broken wire.
Automotive power windows use a switched motor to operate a mechanical window regulator. This regulator moves the pane of glass into the door.
To check and confirm the fault try this procedure:--
1) Open the fuse panel and check the fuses for disrupted elements. The fuse panel at the driver's side kick panel, or between the dashboard and the door. In some cars the fuses are mounted in the engine compartment, in front of the driver's side firewall. Check the fuses and replace if faulty.
2)
Test the wiring harnesses from the fuse panel to the switches and from the switches to the window regulator motor. If the circuits test fine, then proceed to the next step. If a wiring harness is shorted or damaged, it will need to be replaced.3) Remove and test the switches on the driver's side door panel. Pry them up with a screwdriver and pull them free of the panel's opening. Disconnect the switch assembly from the wiring harness by pulling the adapter plug from the assembly. Test the switches individually by touching both sides of one switch with the circuit tester. Each switch will have two terminals, and if the tester is positive on both terminals while the window is activated, then the switch is good. Replace the switch assembly if any of the switches fails the test. Most power window switches come in assembled modules and cannot be replaced individually.4) Remove and test (if possible) the power window motor. Turn the armrest bolts and interior door handle screws counterclockwise, then pull the door panel free from the pop rivets. Behind the panel are a window regulator, the window glass, and the electric driver motor. The motor is usually located in the lower right section of the door. Unplug the motor from the wiring harness and unbolt it from the window regulator by turning the bolts counterclockwise. Pull the motor straight out, away from the gears. And check out if motor is receiving exact 12 volts at the terminals. If not then either motor is faulty or there is a confirm short if motor is replaced.
5) If all the above mentioned possibilities are checked out ok then the window regulator needs to be checked. Inspect the window regulator's joints for rust or stiff movement, if the electrical system is operating correctly. These joints can corrode or break, causing the window to stop working. With the door panel off, the window regulator can be removed and replaced by sliding the glass away from the track mounts, then turning all mount bolts counterclockwise and manipulating the regulator out of the door.


Thanks. keep updated for any more query.you can rate this solution and show your appreciation.

Aug 16, 2010 | 2004 Toyota Sequoia

2 Answers

I have a 1997 ford explorer, and it has power seats and power windows.and the windows and seats will not move.all of the fuses have been checked and are good.


If the fuses are checked ok then there is a possibility that either driver door side main switch or the window regulator or the window motor is gone faulty.
If the windows don't work, any of several issues is likely to blame, including no electricity, bad switches, bad motor, damaged window regulator, or even a broken wire.
Automotive power windows use a switched motor to operate a mechanical window regulator. This regulator moves the pane of glass into the door.
To check and confirm the fault try this procedure:--
1) Open the fuse panel and check the fuses for disrupted elements. The fuse panel at the driver's side kick panel, or between the dashboard and the door. In some cars the fuses are mounted in the engine compartment, in front of the driver's side firewall. Check the fuses and replace if faulty.
2) 
Test the wiring harnesses from the fuse panel to the switches and from the switches to the window regulator motor. If the circuits test fine, then proceed to the next step. If a wiring harness is shorted or damaged, it will need to be replaced.3) Remove and test the switches on the driver's side door panel. Pry them up with a screwdriver and pull them free of the panel's opening. Disconnect the switch assembly from the wiring harness by pulling the adapter plug from the assembly. Test the switches individually by touching both sides of one switch with the circuit tester. Each switch will have two terminals, and if the tester is positive on both terminals while the window is activated, then the switch is good. Replace the switch assembly if any of the switches fails the test. Most power window switches come in assembled modules and cannot be replaced individually.4) Remove and test (if possible) the power window motor. Turn the armrest bolts and interior door handle screws counterclockwise, then pull the door panel free from the pop rivets. Behind the panel are a window regulator, the window glass, and the electric driver motor. The motor is usually located in the lower right section of the door. Unplug the motor from the wiring harness and unbolt it from the window regulator by turning the bolts counterclockwise. Pull the motor straight out, away from the gears. And check out if motor is receiving exact 12 volts at the terminals. If not then either motor is faulty or there is a confirm short if motor is replaced.
5) If all the above mentioned possibilities are checked out ok then the window regulator needs to be checked. Inspect the window regulator's joints for rust or stiff movement, if the electrical system is operating correctly. These joints can corrode or break, causing the window to stop working. With the door panel off, the window regulator can be removed and replaced by sliding the glass away from the track mounts, then turning all mount bolts counterclockwise and manipulating the regulator out of the door.
Thanks. keep updated for any more query.you can rate this solution and show your appreciation.

Aug 10, 2010 | Ford Explorer Cars & Trucks

1 Answer

Windows not working


If the windows don't work, any of several issues is likely to blame, including no electricity, bad switches, bad motor, damaged window regulator, or even a broken wire.
Automotive power windows use a switched motor to operate a mechanical window regulator. This regulator moves the pane of glass into the door.
To check and confirm the fault try this procedure:--
1) Open the fuse panel and check the fuses for disrupted elements. The fuse panel at the driver's side kick panel, or between the dashboard and the door. In some cars the fuses are mounted in the engine compartment, in front of the driver's side firewall. Check the fuses and replace if faulty.
2) 
Test the wiring harnesses from the fuse panel to the switches and from the switches to the window regulator motor. If the circuits test fine, then proceed to the next step. If a wiring harness is shorted or damaged, it will need to be replaced.3) Remove and test the switches on the driver's side door panel. Pry them up with a screwdriver and pull them free of the panel's opening. Disconnect the switch assembly from the wiring harness by pulling the adapter plug from the assembly. Test the switches individually by touching both sides of one switch with the circuit tester. Each switch will have two terminals, and if the tester is positive on both terminals while the window is activated, then the switch is good. Replace the switch assembly if any of the switches fails the test. Most power window switches come in assembled modules and cannot be replaced individually.4) Remove and test (if possible) the power window motor. Turn the armrest bolts and interior door handle screws counterclockwise, then pull the door panel free from the pop rivets. Behind the panel are a window regulator, the window glass, and the electric driver motor. The motor is usually located in the lower right section of the door. Unplug the motor from the wiring harness and unbolt it from the window regulator by turning the bolts counterclockwise. Pull the motor straight out, away from the gears. And check out if motor is receiving exact 12 volts at the terminals. If not then either motor is faulty or there is a confirm short if motor is replaced.
5) If all the above mentioned possibilities are checked out ok then the window regulator needs to be checked. Inspect the window regulator's joints for rust or stiff movement, if the electrical system is operating correctly. These joints can corrode or break, causing the window to stop working. With the door panel off, the window regulator can be removed and replaced by sliding the glass away from the track mounts, then turning all mount bolts counterclockwise and manipulating the regulator out of the door.
 
Thanks. keep updated for any more query.you can rate this solution and show your appreciation.

Jul 10, 2010 | 1995 Toyota Camry

2 Answers

Power window switch on driver side of cadilac 1998 deville needs to be replaced, what part of the assembly (there is a black frame and a wood grain frame around switch) must i lift in order to change the...


there may be a couple of screws that hold the door handle assembly to the door if so remove them so you can lift it up, if not it may be that you have to push back on the inside door handle assembly to remove the top of the are where the switches are located. You will have to get this loose and lifted to access the switch.

Apr 18, 2010 | 1998 Cadillac DeVille

1 Answer

The passenger side front window and driver's side rear window do not go up or down. what could be problem?


I would suspect the switched first. One window might show as a wiring fault but two, no usually.. remove the switch assembly from the door armrest and use a test probe to check the centre terminals of the front and rear window switches. The centre terminals transpose the power and earth supplies when the switch is pushed up and down. If you lose either the power or earth connections during the switching tests, replace the switch assembly.

Dec 24, 2009 | 1996 Toyota Camry

2 Answers

Passenger Window Stuck all the way Down


Try switching the power window switch from the passenger side to the drivers side. Before you do that try with the switch on the up position, wiggle it from side to side. The contacts may be worn and by wiggling it may make contact. Other then that try to park it in side or garbage bag taped to keep rain out till you get it to the shop.
Hint, take it to a Auto window repair shop to replace the switch if it's bad or if the motor is bad. They have more experience to removing the door panels and removing the power window regulator (motor) if that needs to be replaced.
Good luck and hope this helps. 

May 30, 2009 | 1999 Dodge Caravan

1 Answer

My 2003 Forester driver side window wont work.


You need power window regulator as the cable of the regulator is out its place ,

  1. Remove the gusset cover.
  2. Pull up the inner door handle cover toward you to remove the upper hook. Pull down it to remove the lower hook. Remove the inner door handle cover.
  3. Remove the power window switch assembly.
  4. Using a trim panel remover, remove the clips of the trim panel.
  5. Remove the speaker.
  6. Using a spatula, remove the door sealer.
  7. Remove the outer mirror assembly.
  8. Remove the front end of the door weatherstrip and gusset.
  9. Remove the stabilizers.
  10. Remove the rear end of the door weatherstrip (inner and outer).
  11. Operate the power windows switch so the bolts from the regular assembly are visible through the service holes. Remove the mounting nuts.
  12. Take out the door glass. CAUTIONDo not turn the regulator in closing direction after removal of the glass. Otherwise gear may be disengaged.
  13. Loosen the nuts to remove the rear sash.
  14. Disconnect the power window motor wiring harness.
  15. Loosen the four bolts and two nuts to pull out the regulator assembly.
  16. Remove the screws to remove the motor from the regulator assembly.
  17. Installation is the reverse order of removal.0759a6d.jpg23cb1e4.jpg

Good luck...

Oct 21, 2008 | 2001 Subaru Forester

Not finding what you are looking for?
2005 Buick LaCrosse Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...