Question about 2000 Mitsubishi Eclipse

1 Answer

My legnum had black smokeand it wont start anymore, so I checked and found the timing belt worn out, then I changed it to a new one, and put everypart back, when l start again, it starts but it wont operates any more. can anyone help me on this problem Mitsubishi Legnum 2.4 L year 2000 Engine model 4g64

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

  • Expert
  • 88 Answers

The timing is out

Posted on Jan 31, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2005 Mazda RX-8 wont start


Which pulley? Timing belt...

Sep 24, 2017 | 2005 Mazda RX-8

3 Answers

I was driving on hwy., car died suddenly, so I towed it to my house. I found out timing belt had jumped several teeth. I put new belt on, put it on marks, now my car starts and dies immediatley unle


If the belt keeps jumping, I would say you have a badly worn sprocket or the belt tensioner needs checking, it may need a new tensioner or your procedure for tightening it needs to be checked.
If no mark for the idler, then just put it at the 4 o'clock position, as you are facing it.

Jan 22, 2013 | 1982 Volvo 240 Series

1 Answer

Correct procedure for changing timing belt on Legnum gdi wagon '97


You do not need a little advice from an online auto repair blog, you need a SERVICE MANUAL. I would recommend purchacing a service manual for your vehicle at your local parts retailer or subscribe to online service information on a professional automotive service information provider such as alldatadiy.com

The small fee will be well worth the investment.

May 06, 2012 | Mitsubishi Galant Cars & Trucks

2 Answers

1992 mazda mpv, 6 cyls. it occurs a year ago after tune up. its luck power. during smog test, and now it cranks but wont go through when it start. changed the rotor, spurk plugs and cable


Check your gas for possible water. Just in case try a can of SEAFOAM in your gas. It will take about 10 min of running to work. Also recheck the gap on the spark plugs it should be .044 gap. One other thing to check is the firing order and make sure the wires were put back in the right place to the right spark plug

Jan 10, 2011 | 1992 Mazda MPV

3 Answers

1995 toyota coroll turns over but wont start.no spark at plugs, changed cap and rotor


sounds like you need an ignighter which controls spark and it can be found in the distributor under the cap it should have a plug (wire harness) on it.

Nov 14, 2009 | 1995 Toyota Corolla

1 Answer

Car wont start all the time


is the battery holding a good charge.....check gauge on dash, the needle should show about 13v . Also if your battery is well over three years old ...get a new one..about 600-900 cold cranking amps! your belt could be worn too if its never been changed, i would advise that you change it, it will help the alternator keep your new battery charged properly.

Oct 04, 2009 | 1985 Toyota Corolla 2 Door

1 Answer

The belt makes noises when you put in gear


Sounds like you have a worn out belt right there.. try to change the belts and you shouldn't hear the noises anymore..

Jul 11, 2009 | 1995 Isuzu Rodeo

3 Answers

Engine noise on area of pulleys and sometimes engine tries to sto


Don't know if this helps. Had squeel in belt area. Occasionally engine would stop when squeel got loud and sometimes engine would try to quit while going at various speeds. Found tensioner pulley was bad and changed it. Still squeeled and engine would stop when squeel got loud. This time while sitting in yard. Further checking found binding in power steering pump. Will be putting on new one tomorrow. Hope it works. Will update.

Nov 28, 2008 | 2004 Ford Freestar

Not finding what you are looking for?
2000 Mitsubishi Eclipse Logo

291 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8560 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...