Question about 2002 Ford F250 Super Duty SuperCab
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: cruise control won't work
Does the on light in the dash come on? If not, you may have a broken switch in the steering wheel which is a fairly cheap repair. Otherwise, the controls work through the Printed Circuit Board in your dash (your instrument cluster) and the problem could be as simple as a solder defect or faulty component. The problem is that no Ford Service Technician that I know will touch this and tell you that you need to replace it.
The instrument cluster is very easy to replace but may cost you a few more dollars than you want to spend. I would have someone with an electrical background check the cruise control switches in your steering wheel with a multimeter before going any further with this. Also check the wiring for resistance leading from the switch to the cluster.
Posted on Aug 06, 2008
I looked at the owner's manual (starting at pg 162) at the fuse block and it does not mention either of those two particular functions as they relate to a specific fuse. I would recommend you get a tester and check all the fuses to be sure. Good luck! Oh yeah, you can get a copy of the owners manual in PDF format by going to MotorCraftService.com
Posted on Dec 21, 2008
there is a control box for the cruise control behind the glove box . You can remove the cover by pushing in from both sides of the glove box door . the control box will be just inside the glove box to the top. it simply unplugs. any junk yard with an aerostar or ranger or explorer will have one of these control boxes fairly cheap. these control boxes are commonly known to just quit workingand are a very easy fix.
Posted on Feb 09, 2009
SOURCE: cruise control
ok, there are two issues. one could be a fuse that you can exchange out with a working one. secondly, this could be a sensor that is connected to the cruise control assembly under the hood. i would pop the hood to see if the cruse control assembly has became stuck or the cable may have been severed as well.
Posted on Mar 02, 2009
Did you have the recall done on it ?
recall 05S28. Description: Speed Control Deactivation Switch.
It could be a blow fuse in the recall harness, if you did have it done.
Try the self test, and see what the results are. If you do not get it into self test mode, it could be the fuse in teh recall harness that is blown. The 1st revision of the recall harness was an inline ATM fuse, not sure if the revision 2 was the same. If that fuse is blown, the switch is leaking, and should be checked.
This test is a key on engine off (KOEO) test only that is conducted in park only with emergency brake fully engaged.
1. Enter self-test diagnostics by depressing the speed control OFF switch while turning the ignition key ON, making sure the engine does not start and is not running. The speed control indicator on the instrument panel will flash once to indicate that speed control module entered the diagnostic mode. Five additional flashes at this point indicate a defective speed control servo. Release the OFF switch.
2. Press the remaining switches in this sequence: ON, RESUME, COAST and SET/ACCEL.
If the ON switch is not depressed within five seconds after entering the diagnostics mode, the module times out and the procedure must be started over.
The speed control indicator lamp will flash as each switch is depressed. Press each switch in the sequence immediately after the indicator light goes out for the previous switch.
There will be a slight delay when the last button is pressed and the lamp flashes.
3. A lamp flash with the last button (SET/ACCEL) indicates that the static test passed. If the lamp does not flash with the last button and there are no additional flashes of the lamp, the switch is defective.
If the lamp does not flash with the last button, and additional flashes occur, follow the chart below for trouble codes:
— 2 flashes - BPP defective, circuit is defective, brake applied, CPP switch or jumper (if equipped).
Posted on Feb 23, 2010
Tips for a great answer:
this case, to troubleshoot this problem, there are solved help links. Click the
link directly and refer the details to solve this problem yourself, with help
of diagrams: ------
and cruise control not working on Plymouth Grand Voyager?
Nov 28, 2012 | GMC Cars & Trucks
----------- Horn and Cruise control quit working?
Horn and cruise control not working on
Plymouth Grand Voyager?
Horn and Cruise control quit working on 2003 Jaguar S-Type? http://howtobyme.blogspot.com/2011/11/horn-and-cruise-control-quit-working-on.html
Cruise Control stops working, Excessive cranks to start the engine and RPM goes max 2500 http://whoisbyme.blogspot.in/2012/07/cruise-control-stops-workingexcessive.html
Cruise control stop working on 1994 Ford ranger? http://technoanswers.blogspot.in/2012/02/cruise-control-stop-working-on-1994.html
Cruise control not working? http://schematicsdiagram.blogspot.com/2011/12/cruise-control-not-working.html
1996 Ford Explorer: Cruise Control Wiring Diagram?
These will help.
Nov 22, 2012 | 2003 Ford Expedition
Jun 12, 2012 | 2008 Kia Optima
-----------Horn and Cruise control quit working?
Horn and cruise control not working on car?
Horn and Cruise control quit working suddenly?
Cruise control stop working ?
ford ranger cruise control not working?
My Cruise control not working?
This troubleshooting help links will help you to confirm the problem.
Feb 13, 2012 | Chevrolet 3500 Cars & Trucks
Jan 24, 2010 | 2002 Chevrolet Blazer
Nov 30, 2009 | 2005 Chevrolet Impala
Mar 06, 2009 | 1997 Oldsmobile Cutlass Supreme
Feb 09, 2009 | 1994 Ford Ranger Supercab
Oct 30, 2008 | 1993 Ford F150 SuperCab
Oct 04, 2014 | 2002 Ford F250 Super Duty SuperCab
412 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: