Question about Toyota Land Cruiser

1 Answer

Steps to replace clutch master cylinder on 97 model prado

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 313 Answers

  • remove oil line
  • undo mounting bolts for master cylinder
  • install new one
  • install lines
  • bleed master and slave if has one.

Posted on Sep 10, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replacing and bleeding of clutch slave cylinder


If it goes to the floor you have either blown out slave cylinder or master cylinder, no two ways about that.

Jan 10, 2017 | Cars & Trucks

6 Answers

SAAB manual gearbox fluid check & fill location


http://en.allexperts.com

http://www.ptdoityourself.net/tl/tl_indexmain.html

above links will help u get step by step information to solve all problems regarding almost all the cars .

feel free 4 further assistance .rate the particular experts solution as fixya that helps u understand n solve ur problem

Jun 26, 2008 | 1995 Saab 900

1 Answer

Recently replaced clutch kit flywheel hydraulic slave cylinder on a 97 Chevy s10 4.3. Once the clutch system has been bled the clutch pedal pops off clutch master cylinder when pedal is hard. Any...


Not sure if I understand your question. Sounds like the push rod from the clutch master cylinder is pushing the cylinder off the firewall. If that is the case it could be that your rod wasnt fully engage into your cylinder make the rod to long and with enough pressure is popping the clip off the fire wall

Jan 12, 2015 | Cars & Trucks

1 Answer

Location of clutch reservoir Toyota hiace 97 model


Clutch reservoir is right along side the brake master cylinder on the firewall under hood. Just like the brake, it's actuated by a rod from the pedal.

Sep 24, 2014 | Cars & Trucks

1 Answer

I have a honda accord coupe 94 the clutch stops workin after i start the car i ihe car doest accelerates


If you mean you step on the clutch, put transmission in gear and release clutch with no engagement (pedal returns to top position) there is a good chance your clutch disc or pressure plate, or both are worn out and need replacing.
If your clutch pedal is going to the floor and not returning there could be a leak in the system, a bad clutch master cylinder or a bad slave cylinder on the transmission. Check the fluid level in the clutch master cylinder. If it is low or empty you have a leak or component failure. Visually inspect clutch master, line, slave cylinder for fluid leaks. replace as needed. If hydraulics are o.k., suspect clutch disc/pressure plate.

May 09, 2014 | 1994 Honda Accord

1 Answer

How to change a master cylinder


a Master rates about a 5 out of 10 with 10 being the hardest

you may find the hardest part is the actual bench bleeding of the master
and/or
the replacement of the reservoir

These are the instructions from my service manual, but I do not remove the fluid prior to service steps 2-6

  1. Disconnect battery ground cable. Disconnect electrical connector from filler cap.
  2. Remove fluid reservoir filler cap.
  3. Raise and support vehicle.
  4. Remove front wheels.
  5. Remove dust cap and loosen bleed nipple. Connect a bleed tube to bleed nipple and into a suitable container.
  6. Pump brake pedal until all fluid is expelled. Tighten bleed nipple.
  7. Lower vehicle. Install brake fluid reservoir cap. Remove air cleaner and air cleaner outlet tube.
  8. Disconnect central electrical box electrical connector.
  9. Remove central electrical box retaining screw.
  10. Remove central electrical box and relocate to air cleaner area.
  11. Disconnect brake fluid feed tube. Disconnect brake lines.
  12. On models with anti-lock brakes, disconnect brake lines from Hydraulic Control Unit.
  13. On all models, remove brake booster vacuum hose.
  14. Extract master cylinder from vehicle.
  15. On models with manual transaxles, remove clutch hose from brake/clutch reservoir.
  16. On all models, remove master cylinder nuts and remove master cylinder.

To install, reverse removal procedure. Bleed brake system.

May 31, 2010 | 2001 Ford Focus

1 Answer

How do i replace a power brake booster on a 97 ford taurus


  1. Step 1 Mark the brake lines coming into and out of the master cylinder using masking tape and permanent marker.
  2. Step 2 Orient the tube wrench so that it grabs the end of the nut by first sliding it over the brake line.
  3. Step 3 Pull the brake lines out of the master cylinder.
  4. Step 4 Unbolt the two bolts that hold the master cylinder to the brake booster.
  5. Step 5 Slide the master cylinder off the brake booster.
  6. Step 6 Remove the bolts that hold the brake booster to the firewall.
  7. Step 7 Remove the cotter pin from the pin holding the back of the brake pedal to the master cylinder.
  8. Step 8 Slide the brake booster to brake pedal pin out of the mounting bracket.
  9. Step 9 Pull the brake booster off the firewall.
  10. Step 10 Install the new brake booster. Installation is the reverse of removal.

Apr 24, 2010 | 1997 Ford Taurus

1 Answer

How do you replace the slave cylinder


Step 1
Raise the vehicle and support with jack stand placed underneath the frame.
  • Step 2 Remove the cover from the reservoir on top of the clutch master cylinder. It will be located in the engine bay on the driver side of the firewall, near the brake master cylinder. Fill the reservoir with DOT 3 brake fluid. Do not allow the reservoir to run dry at any time during the bleeding process.
  • Step 3 Locate the clutch slave cylinder. It will be bolted to the clutch housing. Locate the small bleeder screw near where the hydraulic hose connects to the slave cylinder.
  • Step 4 Connect a length of clear plastic tube to the bleeder screw.
  • Step 5 Open the slave cylinder bleeder screw, by turning it counterclockwise. Have an assistant pump the clutch pedal until clean brake fluid seeps out of the bleeder screw. Then close the bleeder screw. Make sure the clutch master cylinder does not run dry.
  • Step 6 Have the assistant pump the clutch pedal a few times and hold it against the floor. While the pedal is held against the floor, open the bleeder screw and allow the some fluid to seep out. Close the bleeder screw before releasing the clutch pedal.
  • Step 7 Repeat the process listed in the step above and watch the fluid seeping out of the slave cylinder. The clutch is fully bled when there are no more air bubbles in the fluid seeping out of the slave cylinder. You will be able to see the bubbles in the clear plastic tubing. Do not allow the clutch master cylinder to run dry at any point.
  • Step 8 Lower the vehicle.
  • dont forgate to rate
  • Mar 02, 2010 | 1999 Isuzu Rodeo

    1 Answer

    Bled the clutch and slave cylinder on 97 suzuki sidekick sport and I still have no clutch pedal


    You may have a worn out clutch master cylinder. Check if there's fluid leak at the rear portion of the cylinder.

    Jul 08, 2009 | 1997 Suzuki Sidekick

    2 Answers

    97 chevy cavalier 2.2l 5sp clutch problem


    get the hyd clutch system assembly complete and pre-bleed from the dealer

    Sep 03, 2008 | 1997 Chevrolet Cavalier

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    118 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Toyota Experts

    yadayada
    yadayada

    Level 3 Expert

    75807 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22133 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8172 Answers

    Are you a Toyota Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...