Question about 1988 Mercury Grand Marquis
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
It's behind the back of the intake manifold in the center back, very hardto get too and even harder to see. The pressure switch is on the firewall behind the back of the engine follow the hoses ( plastic lines ) one hooks to the valve
Posted on Aug 11, 2009
well if it is the 3.8 it is on the side of the plentum its alittle black box with two hoses and a wire conector if v-8 will be on the back of motor and will be a little silver box with the 2 hoses and wire connector and the sensor is called D.P.F.E. sensor at ford
Posted on Aug 15, 2009
Jack up the passengers side of the car, get a 1 1/16" wrench break loose the fitting to the manifold, hold a 24 mm wrench on the fitting to the manifold, loosen the flare nut on the tube. Then using a 10 mm socket, about 2 inches long, loosen the two nuts under the EGR valve, then take the both out, remove the vacuum hose to the top of the EGR valve, and the sensing line from the small tube. then completely remove the flare nut from the orifice fitting on the manifold. BE CAREFUL with the tube, do not bend it or break it, you may find PB blaster useful the night before on a cold engine loosen these fittings. Once the EGR valve is out, remove the orifice out of the manifold, remove the tube from the EGR valve, again be careful, mark the tube to EGR position before pulling this off, because the top fitting to EGR needs tightened before you put it back in, it will make the lower fitting difficult if you do not line it up right, dry fitting from under the car is helpful, mark it, and then tighten the top. Clean out the tube, be careful not to bend the little tube, either inside or outside the larger tube, it sticks out inside. Clean the orifice, clean the manifold face carefully not to score it, check for blockage there too. Apply anti-seize to the orifice, put it back in the manifold, then apply anti-seize to the bolts for the EGR valve, and the flare nuts both ends. Apply some silicon to the EGR valve face, just enough to hold the gasket in place, put the new gasket on, start the bolts two turns in the gasket, it will hold them in place, then start them in the manifold, then start the lower flare fitting to orifice, tighten the top bolts, and then the flare nut, connect the vacuum line, connect the sensing line. I just recently did this process, it works, if have other EGR issues, the valve is the easiest.
Posted on Oct 13, 2009
There are eight COPs (coil-on-plugs) to remove. Using a 7mm or 9/32" socket, remove each bolt securing each COP to the intake manifold on top of the engine. Remove all eight COPs, and the spark plugs are underneath. When replacing the spark plugs, use only the proper Ford/Motorcraft plugs, even if they cost twice as much as the aftermarket ones. You will avoid further headaches this way. Hope this helps.
Posted on Mar 30, 2010
Tips for a great answer:
Nov 12, 2015 | Mercury Cars & Trucks
Sep 18, 2014 | 1995 Mercury Grand Marquis
Jun 15, 2012 | 2003 Mercury Grand Marquis
Apr 16, 2011 | 1995 Mercury Grand Marquis
Mar 14, 2011 | 1989 Mercury Grand Marquis
Nov 28, 2010 | 1994 Mercury Grand Marquis
Sep 23, 2009 | 1988 Mercury Grand Marquis
Aug 11, 2009 | 2002 Mercury Grand Marquis
129 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: