Question about 1997 Dodge Neon

2 Answers

Hi i have a 97 neon it will turn over but not start we replaced the spark plugs, ignition coil, and cam shaft sensor can you tell me what else it would be?

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 7,353 Answers

It could be the Crankshaft Position Sensor, if you want another guess.

Posted on Sep 10, 2010

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 36 Answers

The starter.

Posted on Jun 06, 2016

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2005 dodge neon that will crank but wont start. I have replaced the cam shaft sensor, crank sensor and the coil pack. Iam also not getting spark to the coil pack. Any suggestions?


Primary voltage to several systems, including the ignition coil, dark green wire with orange tracer. That voltage comes from asd relay. There is a fuse for asd relay. To check for voltage the engine has to cranking. The control side of asd relay, the computer has to ground it before it will energize. Did you check wiring circuits for cam and crank sensor connectors before replacing sensors? Are there any applicable trouble codes?
Are you ok with testing wiring circuits?

Feb 16, 2017 | 2005 Dodge Neon

2 Answers

97 oldsmobile achieva wont fire changed coil pack spark plugs cam sensor still wont start


Make sure battery has a full charge and battery connections all good.
If it cranks good but won't start, have a helper crank it while you visually check for spark at the spark plugs. If spark everywhere, use a gage and check proper fuel pressure and fuel injector pulse.
If you having a problem with more than one system, I want to check for rpm signal, that usually comes from the crank sensor. Not sure why you replaced cam sensor? I always want to check sensor wiring circuits before replacing anything. Don't replace anything unless your testing points in that direction.

Nov 04, 2016 | Oldsmobile Cars & Trucks

1 Answer

Jeep cranks but does not start


Hi, First replace your plugs. Second check ignition coil(s) one maybe bad. replace with new. If all else is good, have your mechanic check the computer codes. (code scanner) Many of todays cars and trucks have computers to run and control the engine. (management system). Good luck

Feb 04, 2015 | 2004 Jeep Liberty

1 Answer

If 3100 engine is running smooth could the cam shaft sensor be bad in a pontiac grand prix


Not CAM or Crank angle sensor.. Try check supply fuel line pressure n spark plug n ignition coil output.. the ignition coil output should be blue spark n spark jump at least half inch.. But be careful coz its hi tension..

Feb 01, 2013 | 1998 Pontiac Grand Prix

2 Answers

1990 Isuzu 2.6 L 5 spd. No start.. Fuel pressure is ok, not getting spark. Checked coil, ignition module, distributor, computer and coil wire. No power coming from the coil. Small voltage going into...


assuming you the coil, plugs, cap, rotor and wires are good. check the cam sensor, If you have 12 volts to the coil using a 12v light tester. The cam sensor responsible for sending info to the computer telling it that the cam is turning, then the computer tell the coil to dispurse the charge/sparks to the distributor as distributor distribute the sparks to each plugs from the rotor of the distributor. Replace the cam sensor, it tend to go bad over period of time.

Dec 23, 2009 | 1990 Isuzu Spacecab

2 Answers

97 dodge neon died replaced parts and still no spark HELP.


YOU NEED TO CHECK DARK GREEN/ORANGE WIRE AT IGNITION COIL WHEN CRANKING ENGINE FOR POWER..IF NO POWER,SHUTDOWN RELAY IS NOT BEING ENERGIZED..THIS ENGINE ALSO HAS CAMSHAFT POSITION SENSOR ON END OF CYLINDER HEAD..ENGINE CONTROLLER NEEDS CAM AND CRANK SIGNALS TO ENERGIZE THE SHUTDOWN RELAY..UNPLUG CRANK SENSOR AND CHECK VOLTAGE ON ORANGE WIRE..SHOULD HAVE APPROX 8V..IF NOT..UNPLUG CAM SENSOR AND SEE IF 8V SUPPLY RETURNS..IF NO POWER TRY UNPLUGGING VEHICLE SPEED SENSOR LOCATED IN TRANS HOUSING WHERE RIGHT SIDE AXLE COMES OUT OF TRANS..IF 8V RETURNS..THE SPEED SENSOR IS SHORTED INTERNALLY..THESE 3 SENSORS SHARE THE SAME 8V SUPPLY CIRCUIT..WITH SPEED SENSOR UNPLUGGED,PLUG CRANK SENSOR BACK IN AND TRY TO START ENGINE..HAVE SEEN THIS SAME PROBLEM AT WORK RECENTLY

Jul 18, 2009 | 1997 Dodge Neon

Not finding what you are looking for?
1997 Dodge Neon Logo

324 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...