Question about 2004 GMC Sierra Denali

Open Question

How to remove a center console. I have removed 4 screws at this point and it won't come out.

Posted by on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 651 Answers

SOURCE: I cannot remove the CDplayer from my 1999 TWIN CAM HYUNDAI EXCEL

try pulling it out, it should come out far enough to get at the screws. they got it in there without removing all the other stuff, so it has to come out. you may need to purchase a removel tool at a local parts store, there are several differant kinds so ask someone at the store to look at it. they should be able to tell you which one you need. they only cost a couple dollars.

Posted on Dec 29, 2008

motor1258
  • 6674 Answers

SOURCE: How to remove cupholder console on 2003 Explorer

did you try just sticking meter probe or test light probe in the hole,dead center at back for indication of power to it? Careful not to touch sides if using test light, you will blow a fuse. Steady hand.

Posted on Jan 04, 2009

  • 2 Answers

SOURCE: How to remove center console or where to get the diagram? Thanks Tony

In my 2004 Sierra the console is held in by the seat bolts. You will need a star 16 and 20 to get the seats out. There are 2 bolts that go into the dashboard also. There is a big electrical connection under the console that needs to be unplugged to get it out.

Posted on May 23, 2009

  • 2 Answers

SOURCE: how to remove jaguar center console

As in you want a diagram? Either way, I don't have one but I have managed to remove it. I don't know if this might help but I start off by forcibly removing it by holding on to both sides of the top of the console (where the ash tray resides). Upon removal, I remove the cover of the ash tray by unscrewing two screws on both sides of the cover. These require a cross screwdriver. I then take off the connectors to both of the buttons where the gear lever is. The leather surrounding the handbrake is a bit tricky to remove. Slowly unbutton it then remove the top plastic part; you might lose the little spring that holds the button if you aren't careful. Then open the arm rest. Two Torx screws are located by the pivot point of the arm rest. I'm sorry I can't remember the size (most likely an T8). That's just about it. Hope this helps

Posted on Aug 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Removing the center consel on a 2006 Pt Cruiser


REMOVAL
1. Disconnect and isolate the battery negative cable. 2. Remove the four screws located inside the storage bin. 3. Remove the two screws located under the cup holder lining. 4. Disconnect the electrical connectors. 5. Remove the center console from the vehicle.

Oct 31, 2016 | Cars & Trucks

1 Answer

How do you remove the lower center console on a 2000 Olds Intrique


Item Part Number Description 1 060024 Floor console armrest 2 06010 Floor console storage bin 3 04338D Floor console finish panel (front) 4 044D90 Floor console finish panel (center) 5 - Floor console cup holder screws (2 required) 6 13562 Floor console cup holder 7 - Floor console front screws (2 required) 8 - Floor console rear screws (3 required) 9 - Floor console nut 10 045A36 Floor console Removal and Installation
  1. Position the seats as needed to remove the console.
  1. Disconnect the battery. For additional information, refer to Section 414-01 .
  1. Remove the floor console storage bin.
    1. Remove the 3 screws and the armrest.
    1. Remove the floor console storage bin screw.
    1. Remove the pin-type retainer.
    • Disonnect the electrical connectors.
  1. Remove the floor console front finish panel.
    • Pull upward from the front of the trim panel to release the retainers.
    • Disconnect the electrical connectors.
  1. Remove the floor console center finish panel.
  1. If necessary, remove the 2 screws and the floor console cup holder.
  1. Remove the 2 floor console front screws.
  1. Remove the 3 floor console rear screws.
    • To install, tighten to 4 Nm (35 lb-in).
  1. NOTE: Lift the console from the rear and slide it rearward to release the rear seat heater ducts from the instrument panel. Remove the nut and the floor console.
    • Disconnect the electrical connector.
    • To install, tighten to 8 Nm (71 lb-in ).
  1. To install, reverse the removal procedure.

Jun 10, 2015 | 2000 Oldsmobile Intrigue

1 Answer

How to remove center console from 2008 dodge caliber


Hi Rich, hope you well today here's is the fix you need.


23 - Body/Interior/CONSOLE, Center/Removal REMOVAL [img id=LOPTableImg src="https://w05.dealerconnect.chrysler.com/service/mds2002/common/images/collapse.gif"> Click to display a list of Labor Operations associated with this procedure
248438.jpg 1. Pull back on parking brake (5) to the upright position. 2. Open console door and remove two screws (1) fastening console to rear floor bracket (3). 3. Carefully pry up until the retainers (1) disengage from the center console to front floor bracket (6). 4. Disconnect center console wire connector (2) to instrument panel connector. 5. Remove from vehicle.

Hope this help and have an awesome day Rich.

May 23, 2014 | 2008 Dodge Caliber

1 Answer

How to install a center console on a pacifica


Hi Melissa, I'm glad to help, here is the instruction below I said I'd send. Have an awesome day.


23 - Body/Interior/CONSOLE, Floor, Front/Removal REMOVAL [img id=LOPTableImg src="https://w05.dealerconnect.chrysler.com/service/mds2002/common/images/collapse.gif"> Click to display a list of Labor Operations associated with this procedure 1. Remove shift bezel. (Refer to 23 - Body/Interior/BEZEL, Shifter - Removal) .
2. Remove transmission range indicator surround bezel Figure 1.
3. Remove two screws attaching front floor console to the lower instrument panel Figure 2. 4. Open cup holder and remove two attaching screws to bottom of cup holder. 5. Open bin and remove two attaching screws to bottom of bin. 6. Remove front floor console sidewall attaching screws, three per side. 7. Raise front floor console and disconnect wiring harness. 8. Remove front floor console from vehicle.
374297.jpg Figure 1 - TRANSMISSION RANGE INDICATOR SURROUND BEZEL 1 - INSTRUMENT PANEL 2 - AUTOSTICK SHIFTER ASSEMBLY 3 - TRACTION CONTROL SWITCH 4 - TRANSMISSION RANGE INDICTOR SURROUND BEZEL 5 - KNOB SET SCREW 6 - SHIFTER KNOB 7 - FLOOR SHIFT BEZEL 8 - WIRE CONNECTOR 9 - INSTRUMENT PANEL WIRING HARNESS 10 - INSTRUMENT PANEL WIRING CLIP
374299.jpg Figure 2 - FRONT FLOOR CONSOLE 1 - FORWARD CONSOLE CLOSEOUT PANEL 2 - CLOSEOUT PANEL PUSH PIN RETAINER 3 - INSTRUMENT PANEL WIRING 4 - FLOOR CONSOLE BASE 5 - FRONT FLOOR CONSOLE ATTACHING SCREWS TO LOWER INSTRUMENT PANE AND BASE 6 - FRONT FLOOR CONSOLE WIRING CONNECTOR 7 - FRONT FLOOR CONSOLE 8 - ATTACHING L-BRACKETS

May 17, 2014 | 2006 Chrysler Pacifica

1 Answer

How to remove cd player on 1999 acura el


acura cd player is the last to be removed. first start with center console.
push the seats for and remove the 2 screw on the side of console,2 more inside the storage,remove shifter cover and 2 more waiting underneath.remove ashtray,more screws behind,remove center console 3-4in.and now the radio cover is free to be removed. 4 more screw holding the radio.pull slowly and disconnect the wires behind.install in revers order.
dont forget!!! Acura radio have security code.
good luck

Apr 04, 2014 | Cars & Trucks

1 Answer

How do ypou change out the blow fan in a mercury villager 1999


There are 3 screws holding it in. But, you have to remove lower center console (4 attachments, 2 on each side), then remove center trim above console, then remove glove box, then remove 2 ft long steel brace beow glove box, then remove blower. 2 hour job. one screw is hidden by carpet, pull carpet outward for access.

May 29, 2010 | 1999 Mercury Villager

1 Answer

Nissan Maxima'96 - remove dash console


for center console removal start furthest point from dash move seats forward and look for screws of either side of console. may also be in storage area of console. remove back section first which will reveal screws for front which should reveal screws for area that holds cig lighter and such

Apr 24, 2010 | 1996 Nissan Maxima

1 Answer

My 2004 Audi A4 Cigarette lighter socket surrounding broken


Hello, hope this info helps...(subytech1)...Cigarette Lighter In Center Console, Removing And Installing (Vehicles Up To 10.04)

Special tools, testers and auxiliary items required




  • Torque wrench V.A.G 1783



1-Cigarette lighter
  • Removal:
  • Remove center console.
  • Turn center console - 4 - around.
  • Remove two bolts - 3 - on cigarette lighter - 1 -.
  • Disconnect harness connector - 2 -.
  • Remove cigarette lighter - 1 - from recess - 5 -.
  • Installing: Installation is reverse of removal.
2-Connector3-Screws, (2x)
  • Tightening torque 2 Nm
4-Center console5-Cut-out

Aug 07, 2009 | 2004 Audi A4

1 Answer

How do I remove the radio from a 1998 Honda CR-V?


UNSNAP PUSH-PIN FASTENERS FROM BOTTOM OF CENTER CONSOLE
AND REMOVE BOTTOM PANEL.
2. EXTRACT 4 SCREWS FROM BOTTOM EDGE OF BEZEL. EXTRACT 4
SCREWS FORM INSIDE DASH BELOW POCKET. PULL CUP HOLDER/
POCKET ASSEMBLY OUT OF DASH AND REMOVE.
3. OPEN GLOVE BOX AND REMOVE STOPPERS. EXTRACT 2 SCREWS
FROM RIGHT SIDE OF CENTER DASH BEZEL..
4. FROM BELOW STEERING WHEEL EXTRACT 2 SCREWS FROM BOTTOM
EDGE OR PANEL, UNSNAP UPPER EDGE OF PANEL, UNPLUG, AND
REMOVE.
5. UNSNAP TOP EDGE OR CENTER LOWER BEZEL, UNPLUG, AND REMOVE.
6. EXTRACT 2 SCREWS FROM SIDES OF POCKET.
7. UNSNAP RADIO/AC CONTROL DASH BEZEL, UNPLUG, AND REMOVE.
8. EXTRACT 2 SCREWS FROM EACH SIDE OF THE RADIO BRACKET
ASSEMBLY TO REMOVE RADIO FROM DASH/AC BEZEL.

Apr 09, 2009 | 1998 Honda CR-V

1 Answer

To remove the stock stereo


Basically:

1: remove center console - 2 parts where the shifter is located... all of em use clips - just give it a nice pull and it'll pop off
2: remove driver side panel attached to radio console( 2 clips only)
3: remove screw found behind center pocket under a/c control
4: pop out a/c unit (4 clips - 2 on top 2 on bottom) just give it a nice pull... (was scary at first but easy and won't break anything)
5: pull entire front center panel (silver piece that covers radio/ac etc etc)
6: radio is attached via 4 screws - 2 on bottom - 2 on side
7: remove radio
8: make sure u have the AI install kit to install radio w/
9: reattach everything n you're done!

Jul 24, 2008 | 2003 Toyota 4Runner

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

92 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...