Question about 1996 Ford Crown Victoria

Open Question

Where do you put a floor jack on a 1996 crown victoria

Posted by on

6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 28 Answers

SOURCE: crown victoria window motor replacement

remove the door panel. be very careful and make sure you get all the screws out. Should be maybe 2 on the bottom half of the door, and 2 on the top half. one is right by the handle, which is the one i forgot the first time i took my door pannel off. carefully pull the panel upward, and outward at the same time. Once the panel is off, disconnect the controls, and remove the light from the panel. Remove the plastic cover very carefully, it will tear, just keeps noise, and air, and the elements out.
There will be 3 screws, they are torx bolts, once you pull those 3 out. They are located middle of the door towards the right side. The motor will drop down a little bit. disconnect the wires for the motor, and wiggle the motor off of the regulator. the crown vics have a decent size hole to get into the door panel, you can also remove the speaker if that would help you do it. other than that, it just lining up the new motor into the car, pushing it into the regulator, and putting the 3 bolts in, make sure they are snug, and not cross threaded. put everything back together, and your set.

Posted on Mar 19, 2009

  • 33 Answers

SOURCE: need wiring diagram for 2008 ford crown victoria


You can purchase the wiring diagram for $5.99 from the following site: You can also purchase a wiring diagram book from the following link:

Hope this helps,


Posted on Mar 23, 2009

  • 93 Answers

SOURCE: 2000 crown victoria serpentine belt installation

Accessory Drive Component Locationsa0011762.gif

Posted on Jun 09, 2009

  • 75 Answers

SOURCE: How do I change the fuel filter on my 1996 Crown

relieve fuel pressure green cap under hood like tire valve stem then get special fuel filter release tool and slop it over fuel line and slide it into filter the line will then just pull off
slide fuel lines onto new filter till it clicks
thats all

Posted on Jul 03, 2009

  • 17970 Answers

SOURCE: schematic diagram for a ford crown victoria 1996


Fig.: 1995-97 4.6L engine schematic

Hope this help (remember rated this post).

Posted on May 14, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

How can I tell if my motor mounts are broken

Raise car put on stands. Jack engine slightly toward one side and inspect mount. Do same for other side.

Jul 12, 2015 | 1996 Ford Crown Victoria


Where to use a Jack and Jack Stands on a Ford Crown Victoria and Mercury Grand...

Where to use a Jack and Jack Stands on a Ford Crown Victoria and Mercury Grand Marquis

on May 22, 2012 | 1998 Mercury Grand Marquis

1 Answer

My 1996 crown victoria want start

possibly the fact it was an obd1 engine and the 96 is obd2

Dec 25, 2012 | 1996 Ford Crown Victoria

1 Answer

Just need info about changing transmission oil in 1996 Ford Crown Victoria LX. I'm not familiar with type of Transmission oil to use

ford does have their own type you can get it at any parts store just tell them what it's for also at Ford

Aug 27, 2012 | 1996 Ford Crown Victoria

1 Answer

Change alternator in 1996 Crown victoria

Not sure if there is a question here or not.
People tend to not notice the "suggested" answers at the bottom of the screen are put there by the website, and some are months old.

Jun 30, 2012 | 1996 Ford Crown Victoria

1 Answer

I put a new battery and altn and it still will not hold a charge u can jump start it and it will run about four min and then shut off

hello, my name is julie and i'm having the same problem with my 1996 crown victoria and i was wondering if you got any help from anybody about this problem if so could you write me at

thanks so much

Jul 24, 2011 | 1996 Ford Crown Victoria

1 Answer

Where to put freon in 1996 crown victoria

Requires R-134a refrigerant. Look for the black cylinder located on the passenger side under the hood. If you are unsure of how to proceed with recharging the system, consult with a certified technician.

Sep 20, 2009 | 1996 Ford Crown Victoria

1 Answer

My 2004 crown victoria is dead - battery replaced

there is a loose connection on the small wire that hooks to the starter. jack up the car and tap on the wire and starter and it will crank. i had to put a new crimp connector on mine. its starting just fine now. done this to 3 1994's and 2 1993's good luck let me know how it goes. sawdust46

Aug 01, 2009 | 2004 Ford Crown Victoria

1 Answer


Yes you can replace it. It is in the fuel tank. You will need to drain the tank and remove it to gain access to the fuel pump. A floor jack will help when lowering the fuel tank. If you fo to a dealer to do this you will be looking probably around $700.00 to replace the pump.

Feb 17, 2009 | 1994 Ford Crown Victoria

Not finding what you are looking for?
1996 Ford Crown Victoria Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers


Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides