Question about 1995 Toyota T100 Xtracab

1 Answer

I have been trying to remove a timing belt from a 95 T 100 Toyota 3.4 4wd. One book says to just remove the tensioner and it should release the belt. This does not work. Need step by step guide. Please Help? Everything has been removed except for the crank shaft pulley and bottom pulley for tensioner.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 313 Answers

If you remove the tensioner than it should have relieved the tension on the belt and the belt should be free and easy to remove.

Posted on Sep 10, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

1998 Isuzu trooper 3.5 alternator replace


step one remove battery neg lug .
the above video (of book?) is wrong.
the belt tension-ing step was skipped.

remove belt steps remove alt. wiring. remove alternator (bolts) it falls free. replace it , reverse steps above belt back tension belt. battery cable back. test run. charge/BAT lamp off?
see wrench below, turn it CW.
this releases the spring tension and belt comes off
to put back, do same and put on belt and release wrench.

25186758-dk3xh54xw1fmpqbxyhqoyzal-4-0.jpg3.5L only. USA only.

Oct 05, 2014 | Isuzu Trooper Cars & Trucks

1 Answer

Replace serpentine belt



Removal & Installation

  1. Rotate the drive belt tensioner clockwise and remove the drive belt.
    WARNING Never suddenly let go of the tensioned idler pulley. The force of the spring pressure suddenly released may damage the idler pulley mechanism. Always release the spring pressure gradually.


    0996b43f80204f01.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Rotate the belt tensioner to relieve tension on the belt-4.6L engine shown, others similar


To install:
  1. Route the belt over the pulleys making sure all the grooves in the pulleys and the belt line up correctly. Refer to the accessory belt routing section of this manual.
  2. Rotate belt tensioner clockwise and slip drive belt over idler pulley on tensioner.

  1. Rotate the drive belt tensioner clockwise and remove the drive belt.
    WARNING Never suddenly let go of the tensioned idler pulley. The force of the spring pressure suddenly released may damage the idler pulley mechanism. Always release the spring pressure gradually.


    0996b43f80204f01.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Rotate the belt tensioner to relieve tension on the belt-4.6L engine shown, others similar


To install:
  1. Route the belt over the pulleys making sure all the grooves in the pulleys and the belt line up correctly. Refer to the accessory belt routing diagrams above.
  2. Rotate belt tensioner clockwise and slip drive belt over idler pulley on tensioner.
If for any reason, the tensioner is crooked, replace it!!! Also, install the belt with the writing facing you like you are trying to read a book. This WILL (a trick I learned at Mercedes) prevent even a new belt from squeeling!!

Dec 16, 2010 | 2003 Ford Explorer

1 Answer

Need diagram for installation of a serpetine belt for 2005 Toyota Tacoma P/U 4.0. Please advise. Thanks


  1. REMOVE ENGINE UNDER COVER SUB-ASSEMBLY NO.1 (4WD AND PRE RUNNER DRIVE TYPE)
    1. Remove the 4 bolts, then remove the under cover No.1.
    2. dak408_42.gif
  • REMOVE FAN AND GENERATOR V BELT
    1. While releasing the belt tension by turning the belt tensioner counterclockwise, remove the V-ribbed belt from the belt tensioner.
  1. INSPECT V-RIBBED BELT TENSIONER ASSEMBLY
    1. Check that nothing gets caught in the tensioner by turning it clockwise and counterclockwise. If a malfunction exists, replace the tensioner.
    2. dak408_43.gif
    3. INSTALL FAN AND GENERATOR V BELT
    1. While turning the belt tensioner counterclockwise, align with its holes, and then insert a bar of 6 mm (0.24 inch) into the holes to fix the belt tensioner.
    2. Install the V-ribbed belt.
    3. While turning the belt tensioner counterclockwise, remove the bar.
    4. dak408_44.gif
    1. If it is hard to install the V-ribbed belt, perform the following procedure.
(1) Put the V-ribbed belt on all parts except the P/S pump, as shown in the illustration. (2) While releasing the belt tension by turning the belt tensioner counterclockwise, put the V-ribbed belt on the P/S pump.
  1. INSTALL ENGINE UNDER COVER SUB-ASSEMBLY NO.1 (4WD AND PRE RUNNER DRIVE TYPE)
    1. Install the engine under cover with the 4 bolts. Torque: 29 Nm (296 kgf-cm, 21 ft. lbs.)

Nov 21, 2010 | 2005 Toyota Tacoma

1 Answer

Timing belt diagram


complete procedures are posted at AutoZone.com: http://www.autozone.com/autozone/repairinfo/repairguide/repairGuideContent.jsp?pageId=0900c152802619fd

Do you mean timing belt ot serpentine (accessory) belt?
Belt diagrams are below:


0900c15280261782.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Belt routings on the 1FZ-FE engine



0900c15280261783.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Belt routings on the 3RZ-FE engine



0900c15280261784.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Belt routings on the 5VZ-FE engine
2UZ-FE Engine
To remove the serpentine belt on the 2UZ-FE engine, position a suitable sized wrench or ratchet and socket over the belt tensioner bolt, rotate the tensioner counterclockwise to release the belt tension, then remove the belt. The pulley bolt for the tensioner has a left-hand thread.
When installing the belt, make sure it fits properly in the ribbed grooves and check to be sure the belt has NOT slipped out of the groove on the bottom of the pulley.



0900c15280261785.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. On the 2UZ-FE engine, rotate the belt tensioner counterclockwise to release the belt tension

Aug 25, 2010 | 2000 Toyota 4Runner

1 Answer

I am try to replace the serpintine belt for the power steering on


This answer is for a 2003 Toyota Camry listed by the Asker under the 2001 Toyota Avalon Category

Click on the following direct Link. It has the Serpentine Belt Diagram.

Standard Rules to Removal the Serpentine Belt with a Tensioner:
1. Find the Tensioner(s). (See Diagrams on Link)
2. Using a Serpentine Belt Tensioner Tool, Or Wrench OR Ratchet, Rotate/Move the Tensioner USING THE AVAILABLE NUT (on the Pulley or Arm Base) OR the OPENING (3/8ths or 1/2 inch square opening) rotating the Tensioner Pulley/Arm - moving it away from contact with the belt and towards the area where the belt is not in contact with the Tensioner Pulley. The Tensioner is spring loaded, and is hard to rotate/move.
3. Remove the loosened belt off one of the other more easily accessed Pulleys.
4. DO NOT quickly release the Tensioner, but gently allow the Tensioner to rest in its closed position.

Standard Rules for Installing the Serpentine Belt with Tensioners:
a. Pick a Pulley that is most easily accessed. This will usually be on top. This will be the last Pulley that the belt will go on.
b. Using the Diagram: Install the new Serpentine Belt on the remainder of the Pulleys....over, under, left right.
c. Using a Serpentine Belt Tensioner Tool or Wrench or Ratchet Tool: Rotate/Move the Tensioner Pulley/Arm "away" from Belt contact area on the Tensioner. This spring is pretty hard and with a new belt, it will be even harder to install. Rotate/Move this to as-close to the maximum allowed inorder to have enough slack in the belt to get it up and over the last pulley.
d. Using your other hand - Pull the Belt up and over the Last remaining Pulley.
e. Before releasing the pressure on the Tensioner, visually inspect the remainder Pulleys and the Belts' Positioning on them

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.Com!

http://www.2carpros.com/car_repair_information/year/2003/make/toyota/model/camry/2003_toyota_camry_drive_belt_routing_diagram.htm

Mar 21, 2010 | 2001 Toyota Avalon

1 Answer

How do you remove the drive belt of a 2003 Toyota


Click on the following free direct Link. It has the correct Serpentine/Drive Belt Diagrams for your 2003 Toyota Camry with either the 2.4L 4-Cylinder or 3.0L V6 Engine.

http://www.2carpros.com/car_repair_information/year/2003/make/toyota/model/camry/2003_toyota_camry_drive_belt_routing_diagram.htm

"HOW TO":
Standard Rules to Removal the Serpentine Belt with an Automatic Tensioner:
1. Find the Tensioner(s). (See Diagrams on Link)
2. Using a Serpentine Belt Tensioner Tool, Or Wrench OR Ratchet, Rotate/Move the Tensioner USING THE AVAILABLE NUT (on the Pulley or Arm Base) OR the OPENING (3/8ths or 1/2 inch square opening) rotating the Tensioner Pulley/Arm - moving it away from contact with the belt and towards the area where the belt is not in contact with the Tensioner Pulley. The Tensioner is spring loaded, and is hard to rotate/move.
3. Remove the loosened belt off one of the other more easily accessed Pulleys.
4. DO NOT quickly release the Tensioner, but gently allow the Tensioner to rest in its closed position.

Standard Rules for Installing the Serpentine Belt with an Automatic Tensioner:
a. Pick a Pulley that is most easily accessed. This will usually be on top. This will be the last Pulley that the belt will go on.
b. Using the Diagram: Install the new Serpentine Belt on the remainder of the Pulleys....over, under, left right.
c. Using a Serpentine Belt Tensioner Tool or Wrench or Ratchet Tool: Rotate/Move the Tensioner Pulley/Arm "away" from Belt contact area on the Tensioner. This spring is pretty hard and with a new belt, it will be even harder to install. Rotate/Move this to as-close to the maximum allowed inorder to have enough slack in the belt to get it up and over the last pulley.
d. Using your other hand - Pull the Belt up and over the Last remaining Pulley.
e. Before releasing the pressure on the Tensioner, visually inspect the remainder Pulleys and the Belts' Positioning on them.

Let me know if this helped, or if you have additional information questions. Feel Free to contact me at FixYa.com!

Dec 29, 2009 | 2003 Toyota Camry

1 Answer

How to change serpentine belt, 2004 Toyota Tundra


locate tensioner pulley; release tension from belt; remove belt; make sure not to forget how the belt is routed; route belt around all pulleys but tensioner; put tension on tensioner pulley; route belt over tensioner pulley

Oct 03, 2009 | 2004 Toyota Tundra

1 Answer

I want to change belt and tensioner at the same time on 05 corolla.


A 19mm wrench to release the tension

A 17mm wrench to remove the main mounting bolt

A 12mm wrench to remove the upper tensioner mount.

BE CAREFUL not to break the main mounting bolt(17mm head) it is a long bolt.

If you break it the engine will have to be removed to extract the broken bolt.

May 21, 2009 | 2005 Toyota Corolla

1 Answer

Hi, I want to remove my worn alternator belt on my Toyota Corolla 1998 1.8L Engine 7AFE (not Serpentine belt). Anyone know correct procedure or how to release the belt tension? Thanks Phil Auckland New...


i use a 1/2 inch leverage bar .there is a hole in the tension pully(usually the top pully) put the end of the bar in the slot and pull. you will have to hold the tension on it with the bar while you remove the belt.

Apr 25, 2009 | 1998 Toyota Corolla

2 Answers

Toyota camry 2005


if it is a 4 cylinder. there is a 19mm nut on a tensioner inside where the belt runs around the top motor mount. put a large bar on a 19mm socket nd pull towards the front of the car to loosen tension on the belt

Dec 30, 2008 | 2006 Toyota Camry

Not finding what you are looking for?
1995 Toyota T100 Xtracab Logo

Related Topics:

114 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...