Question about 1990 GMC C1500

1 Answer

Im having trouble getting the ignition key codes to have a key made, my grandma w/alseimers lost my keys and chevy only has back to 1992, mine is a 1990 gmc sierra sle cab

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

If you have the current registration take it to a dealer and they should be able to get the key code for you and cut a key

Posted on Sep 13, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Wife lost the keys to her 92 chevy blazer.I got a new ignition cylinder & key I had to force the old cylinder out. Put the new one in and it wont turn forward .So I tried to start it by turning it...


GM cars have a passlock system that uses a transponder and reader from the key to start the engine. Just changing the key and cylinder was not going to start the car. The cars BCM ( body control module computer) has to be programmed to match the new key and cylinder. You will have to take it to a dealer or an automobile locksmith that specializes in ignitions. Taking out the box was the worst thing you could have done. Now you have two things that need fixing. All you had to do was take the cars vin number , your registration and maybe tow it to the dealer and they would have cut you a key and programmed it for you.

Sep 24, 2017 | 1992 Chevrolet S-10 Blazer

2 Answers

Where is the location of the ignition sensor on 2004 kia optima lx 4 cyclinder 4 door sedan


the ignition module is to the left of the air filter, right against the right side of the engine. I replaced mine, just two screws and take off black plastic covering. Make sure u disconnect negative battery post first. When done hook negative back up. If engine light don"t go off for P0320 code, disconnect battery for 5 min and connect back, I let my battery stay disconnect overnight.

Jul 22, 2010 | 2004 Kia Optima

1 Answer

I broke my key off in the lock on my 95 pathfinder.... is the key code located any where in the truck...?


usualy the key code is located in your owners manual at least mine was allso coppy down your vin and call nissan im shure they have some way of looking it up

Jun 07, 2010 | 1992 Nissan Pathfinder

3 Answers

Lost keys to 91 chevy camoaro. put in new ignition switch. will not start . What do I do


the old key might be for the immoberlizer as well if it has one so you will not be turning the immoberlizer off if it is coded to the key

Mar 22, 2010 | 1991 Chevrolet Camaro

1 Answer

My 1999 Chevy Blazer has a key for the ignition and a key for the doors. I lost the only key I had for the doors. Although I can use the clicker to get in, can I get a replacement key for the doors, how...


depends on which key was original==an original key can be cut but are the doors original or ignition vin number will be used to look up key cut code or check with a certified locksmith some of them work with the dealers for key problems

Oct 23, 2009 | 2000 Chevrolet Blazer

2 Answers

Wiring diagram for 92 chevy blazer


My 1992 Chevy blazer s-10 starts and then the door locks automatically starts locking and unlocking...It wont stay running either...

Jun 11, 2009 | 1992 Chevrolet S-10 Blazer

4 Answers

Chevy tahoe shuts off when driving


replace fuel pump relay. check all fuses to ignition and pcm .make sure they are not loose. check coil wires make sure they not loose.look at battery if you have the ac delco seal battery make sure green eye still there .if its black have battery check out.

Apr 29, 2009 | 2002 Chevrolet Tahoe

1 Answer

I cannot get ignition key out of lock, will not turn off. 92 chevy p.u. 2500


Check to see if there is an ignition lock on the unit you might have to push the release, my 1992 2500 stick shift has one and when I first bought it i didn't know about it, so give that a try the unit might not be turning back all the way and in turn will not let your key go.

Oct 04, 2008 | 1992 Chevrolet C/K 2500

1 Answer

Ignition switch


You need to remove the shroud so you can see the whole lock assembly.Once this is removed you should see a little silver retainer pin. While pushing in on the pin, rotate the lock with the key in it, until you feel the pin drop in. At this point you can start to pull the lock out. You may need a torx driver to unscrew some of the bolts, but there are no special tools needed to actually remove the lock assembly , besides a working key.

Aug 22, 2008 | 1992 Chrysler Lebaron

Not finding what you are looking for?
Cars & Trucks Logo

118 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

80637 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...